Using a higher bitclk then expected doesn't always work.
Here is an example:
aplay -Dhw:0,0 -d 5 -r 48000 -f S24_LE -c 2 audio48k24b2c.wav
In this case, the required bitclk is 48000 * 24 * 2 = 2304000
but the closest bitclk that can be derived is 3072000.
Now, for format S24_LE, SAI will use slot_width = 24, but since
the clock is faster than expected, it will start to send bytes
from the next channel so the sound will be corrupted.
Thus, remove bitclk relaxation condition which was added mostly
for supporting S20_3LE format which was removed from SAI in
commit 739e6d654b5c0a ("MLK-14870: ASoC: fsl_sai: Remove support
for S20_3LE").
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
There is occasion that wm8960 reset failed in the beginning,
Especially after board reboot. The issue is found in the
imx7d-sdb board Rev.C. After retry, the reset operation is
successful.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
The input MCLK is 12.288MHz, The desired output sysclk is 11.2896MHz
the sample rate is 44100Hz, with the pllprescale=2, postscale=sysclkdiv=1,
some chip may have wrong bclk and lrclk output in master mode. then there
will be no sound.
With the pllprescale=1, postscale=2, the output clock is correct. so use
this configuration to workaround this issue.
Tested 8k/11k/16k/22k/32k/44k/48kHz case.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
After the suspend/resume, hw_params may be called in bias_level is not
BIAS_ON, then the PLL is not disable/enabled, if the sample rate is
changed, the output clock is not correct.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115041 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bitclk is derived from sysclk using bclk_divs.
Sysclk can be derived in two ways:
(1) directly from MLCK
(2) MCLK via PLL
Commit 3c01b9ee2a ("ASoC: codec: wm8960: Relax bit clock
computation")
relaxed bitclk computation when sysclk is directly derived from MCLK.
Lets do the same thing when sysclk is derived via PLL.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new PLL configuration code triggers a harmless warning:
sound/soc/codecs/wm8960.c: In function 'wm8960_configure_clocking':
sound/soc/codecs/wm8960.c:735:3: error: 'best_freq_out' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
wm8960_set_pll(codec, freq_in, best_freq_out);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/wm8960.c:699:12: note: 'best_freq_out' was declared
here
Fix this by reworking the code such that:
1) When there is no PLL freq available return -EINVAL and make
sure *bclk_idx, *dac_idx, *sysclk_idx are initialized with
invalid values.
2) When there is a PLL freq available initialize *bclk_idx,
*dac_idx and *sysclk_idx with correct values and immediately
return the freq available.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Fixes: 303e8954af ("ASoC: codec: wm8960: Stop when a matching PLL freq is found")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a matching PLL freq is found, searching continues even this is
not necessary. The problem was introduced with the following refactoring
commit 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search)
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for deriving (sysclk, lrclk, bclk)
when the clock is auto or pll.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8960 derives bit clock from sysclock using BCLKDIV[3:0] of R8
clocking register (See WM8960 datasheet, page 71).
There are use cases, like this:
aplay -Dhw:0,0 -r 48000 -c 1 -f S20_3LE -t raw audio48k20b_3LE1c.pcm
where no BCLKDIV applied to sysclock can give us the exact requested
bitclk, so driver fails to configure clocking and aplay fails to run.
Fix this by relaxing bitclk computation, so that when no exact value
can be derived from sysclk pick the closest value greater than
expected bitclk.
Suggested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for finding (sysclk, lrclk, bclk)
when the clock is auto or mclk. This makes code easier to
read and reduces the indentation level in wm8960_configure_clocking.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_codec_driver structures that are only passed to
snd_soc_register_codec or memcpy (2nd arg), for which the corresponding
parameters are declared const. Declare as const snd_soc_codec_driver
structures that have these properties.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_codec_driver i@p = { ... };
@ok@
identifier r.i;
expression e1,e2,e3;
position p;
@@
(
snd_soc_register_codec(e1,&i@p,e2,e3)
|
memcpy(e1,&i@p,e2)
)
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_codec_driver i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of WM8960_SYSCLK_AUTO mode, WM8960_SYSCLK_PLL mode was
made unusable. Ensure we're not PLL mode before trying to use MCLK.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
INBMIX1 controls LINPUTs and INBMIX2 controls RINPUTs, so fix the naming
accordingly.
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/RINPUT1 can line to Left/Right Boost Mixer through boost switch.
If boost switch is open, there will be no voice when using L/RINPUT1.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In normal operation, the left and right channel digital audio data is
converted to analogue in two separate DACs. There is a mono-mix mode
where the two audio channels are mixed together digitally and then
converted to analogue using only one DAC, while the other DAC is
switched off. The mono-mix signal can be selected to appear on both
analogue output channels. The mono mix is automatically attenuated by
6dB to prevent clipping.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the xinvert value from 0 to 1 on the "Capture Switch" control
WM8960 datasheet is shown as follows:
Bit 7 at 00h and 01h register address
1 : Enable Mute, 0 : Disable Mute
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only accept "deemph" values of zero and one, but by mistake we
accept negatives as well. It's harmless but let's clean it up anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the max register value of mic boost pga should be 3.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input PGAs have a gain range from -17.25dB to +30dB in 0.75dB steps.
The boost stage can provide additional gain. For line inputs, -12dB to
+6dB gain is available on the boost mixer. For micphone inputs, it can
provide up to +29dB additional gain from the microphone PGA.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min gain is the corresponding gain value when the register value is 0
instead of 1, just correct it.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sysclk auto mode. When it's sysclk auto mode, if the MCLK is
available for clock configure, using MCLK to provide sysclk directly,
otherwise, search a available pll out frequcncy and set pll.
Configure clock in hw_params may cause problems when using bypass style
paths without hw_params in machine driver getting called. So add configure
clock to set_bias_level.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
the enum of "DAC Polarity" should be wm8960_enum[1].
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and replace all
other manual access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to referance manual, right justify mode can't
support 32 bit word length.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec driver missing configure its bit clock and frame clock for codec
master mode, so add support for it. It will calculate a appropriate frequency
dividing ratio according to the system clock, bit clock and frame clock, then
set the corresponding registers.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It should be "RINPUT3" instead of "LINPUT3" route to "Right Input
Mixer".
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
When we want to use wm8960 codec, we should enable its MCLK in machine driver.
It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition
away from ON. In this case, disable the codec mclk. When current bias_level
is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case,
enable the codec mclk.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Daniel Baluta