Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb0799 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).
This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.
This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds more information for reset DFX. Also, adds some
cleanups to reset info, move reset_fail_cnt into struct
hclge_rst_stats, and modifies some print formats.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pfc_en and pfc_map need to be displayed in hexadecimal notation,
printing dma address should use %pad, and the end of printed string
needs to be add "\n".
This patch modifies them.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the selftest and reset are performed at the same time, the loopback
setting may be still in the enable state after the reset. As a result,
packets cannot be sent out.
This patch fixes this issue by disabling loopback in hclge_mac_init.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unnecessary.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclge_get_reset_level may return HNAE3_NONE_RESET,
so hdev->reset_level can not be assigned with the return
value in the hclge_reset(), otherwise, it will cause
the use of hdev->reset_level in hclge_reset_event get
into error.
Fixes: 012fcb52f6 ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the VF index used incorrectly in function
hclge_set_vlan_rx_offload_cfg() and hclge_set_vlan_rx_offload_cfg().
When VF id is greater than 8, for example 9, it will set the
same bit with VF id 1.
This patch fixes it by using vport->vport_id % HCLGE_VF_NUM_PER_CMD /
HCLGE_VF_NUM_PER_BYTE as the array index, instead of vport->vport_id /
HCLGE_VF_NUM_PER_CMD.
Fixes: 052ece6dc1 ("net: hns3: add ethtool related offload command")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 70a214903d ("net: hns3: reduce the parameters of some functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.
Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.
Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.
This patch also uses a macro to replace 0x1F.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.
Fixes: 72e2fb0799 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the loopback test supports only mac selftest and serdes
selftest. This patch adds phy selftest.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware or IMP get specified error it may need the client
to take some special operations.
This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the waiting time for TQP reset.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]
The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC TNL interrupt is used to collect statistic info about
link status changing suddenly when netdev is running.
But when stopping netdev, the enabled MAC TNL interrupt is
unnecessary, and may add some noises to the statistic info.
So this patch disables it before stopping MAC.
Fixes: a63457878b ("net: hns3: Add handling of MAC tunnel interruption")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer type parameter should be declare as const for preventing
from its pointed value being unexpected modified.
The uninitialized variable can not be return directly. The default
return value is 0 if no abnormal result.
This patch fixes the preceding two errors, deletes redundant
declaration of a function and align one parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To explain some code, this patch adds some comments, and modifies or
merges some comments to make them more neat.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:3190:5:
warning: symbol 'hclge_func_reset_sync_vf' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Before PF asserting function reset, it should make sure
that all its VFs have been ready, otherwise, it will cause
some hardware errors.
So this patch adds function hclge_func_reset_sync_vf() to
synchronize VF before asserting PF function reset. For new
firmware which supports command HCLGE_OPC_QUERY_VF_RST_RDY,
we will try to query VFs' ready status within 30 seconds.
And keep the old implementation for compatible with firmware
which does not support this command.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines the interface for querying MAC pause
statistics, and adds structure hns3_mac_stats to keep the
count of TX & RX.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can use ethtool -d command to dump some registers. However,
these registers information is not enough to find out where the problem is.
This patch adds DFX registers information after original registers
when use ethtool -d commmand to dump registers. Also, using macro
replaces some related magic number.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the pause options of HNS3 shown like this:
"RX/TX" is always the same with "RX negotiated/TX negotiated".
Because of the driver covered the value of "RX/TX" with the value
of "RX negotiated/TX negotiated" after adjust link.
This patch records the pause configurations of the user, and never
covered them in adjust link.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling hclge_reset_event() within HCLGE_RESET_INTERVAL,
it returns directly now. If no one call it again, then the
error which needs a reset to fix it can not be fixed.
So this patch activates the reset timer for this case, and
adds checking in the end of the reset procedure to make this
error fixed earlier.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the reset interrupt is cleared in the reset task, which
is too late. Since, when the hardware finish the previous reset,
it can begin to do a new global/IMP reset, if this new coming reset
type is same as the previous one, the driver will clear them together,
then driver can not get that there is another reset, but the hardware
still wait for the driver to deal with the second one.
So this patch clears PF's reset interrupt status in the
hclge_irq_handle(), the hardware waits for handshaking from
driver before doing reset, so the driver and hardware deal with reset
one by one.
BTW, when VF doing global/IMP reset, it reads PF's reset interrupt
register to get that whether PF driver's re-initialization is done,
since VF's re-initialization should be done after PF's. So we add
a new command and a register bit to do that. When VF receive reset
interrupt, it sets up this bit, and PF finishes re-initialization
send command to clear this bit, then VF do re-initialization.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver sets handshake status to tell the hardware
that the driver have downed the netdev and it can continue with
reset process. The driver will clear the handshake status when
re-initializing the CMDQ, and does not recover this status
when reset fail, which may cause the hardware to wait for
the handshake status to be set and not being able to continue
with reset process.
So this patch delays clearing handshake status just before UP,
and recovers this status when reset fail.
BTW, this patch adds a new function hclge(vf)_reset_handshake() to
deal with the reset handshake issue, and renames
HCLGE(VF)_NIC_CMQ_ENABLE to HCLGE(VF)_NIC_SW_RST_RDY which
represents this register bit more accurately.
Fixes: ada13ee3db ("net: hns3: add handshake with hardware while doing reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable return_status in hclge_get_mac_val_cmd_status()
is useless. So this patch returns the error code directly, instead of
using this variable. Also, replace some '%d' with '%u' in
hclge_get_mac_val_cmd_status().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_info() is more appropriate for printing messages when driver
initialization done, so switch to dev_info().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.
This patch sets the above three subtask's affinity using the
misc interrupt' affinity.
Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use delayed work instead of using timers to trigger the
hclge_serive.
Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating memory, the GFP_KERNEL cannot be used during the
spin_lock period. This is because it may cause scheduling when holding
spin_lock. This patch changes GFP flag to GFP_ATOMIC in this case.
Fixes: dd74f815dd ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: lipeng 00277521 <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, hclge_reset_err_handle() will assert a global reset
when the failing count is smaller than MAX_RESET_FAIL_CNT, which
will affect other running functions.
So this patch removes this upgrading, and uses re-scheduling reset
task to do it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds default value for tc_size and tc_offset, or it may
get random value and used later.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver queries the media port information, and
updates the port capability periodically. But it sets an error
mac->speed_type value, which stops update port capability.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control autoneg is unsupported for fibre port. It takes no
effect for flow control when restart autoneg. This patch fixes
it, return -EOPNOTSUPP when user tries to enable flow control
autoneg.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some MSI-X interrupt's status may be cleared by hardware,
so when the driver receives the interrupt, reading
HCLGE_VECTOR0_PF_OTHER_INT_STS_REG register will get an empty
unknown interrupt. For this case, the irq handler should enable
vector0 interrupt. This patch also use dev_info() instead of
dev_dbg() in the hclge_check_event_cause(), since this information
will be useful for normal usage.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local device and link partner config auto-negotiation on both,
local device config pause frame use as: rx on/tx off,
link partner config pause frame use as: rx off/tx on.
We except the result is:
Local device:
Autonegotiate: on
RX: on
TX: off
RX negotiated: on
TX negotiated: off
Link partner:
Autonegotiate: on
RX: off
TX: on
RX negotiated: off
TX negotiated: on
But actually, the result of Local device and link partner is both:
Autonegotiate: on
RX: off
TX: off
RX negotiated: off
TX negotiated: off
The root cause is that the supported flag is has only Pause,
reference to the function genphy_config_advert():
static int genphy_config_advert(struct phy_device *phydev)
{
...
linkmode_and(phydev->advertising, phydev->advertising,
phydev->supported);
...
}
The pause frame use of link partner is rx off/tx on, so its
advertising only set the bit Asym_Pause, and the supported is
only set the bit Pause, so the result of linkmode_and(), is
rx off/tx off.
This patch adds Asym_Pause to the supported flag to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting -Wformat=2, there is a compiler warning like this:
hclge_main.c:xxx:x: warning: format not a string literal and no
format arguments [-Wformat-nonliteral]
strs[i].desc);
^~~~
This patch adds missing format parameter "%s" to snprintf() to
fix it.
Fixes: 46a3df9f97 ("Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is share buffer in the SSU(storage
switching unit), the low waterline for RX private buffer is
too low to keep the hardware running. Hardware may have
processed all the packet stored in the private buffer of the
low waterline before the new packet comes, because hardware
only tell the peer send packet again when the private buffer
is under the low waterline.
So this patch only allocate RX private buffer if there is
enough buffer according to hardware user manual.
This patch also reserve some buffer for reusing when TC num
is less than or equal to 2, and change PAUSE_TRANS_GAP &
HCLGE_NON_DCB_ADDITIONAL_BUF according to hardware user
manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to enable NIC HW error interrupts during client
initialization in some cases, we should do exception handling to clear
flags and free the resources.
Fixes: 00ea6e5fda ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ROCE HW errors should only be enabled when initializing ROCE's
client, the current code enable it no matter initializing NIC or
ROCE client.
So this patch fixes it.
Fixes: 00ea6e5fda ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing global reset, the MAC autoneg state of fibre
port is set to default, which may cause user configuration
lost. This patch fixes it by restore the MAC autoneg state
after reset.
Fixes: 22f48e24a2 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.
This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.
Fixes: 44e626f720 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VF VLAN filter is disabled when VF VLAN table is full, then the
new VLAN ID won't be added into VF VLAN table, it will always print
fail log when remove these VLAN IDs. If user has added too many
VLANs, it will cause massive verbose print logs.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan