The ->command field is no longer used, remove it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
SPI mem drivers should use spi_mem_set_drvdata() not spi_set_drvdata()
to store their private data. Using spi_set_drvdata() will mess the
spi -> spi-mem link up and cause a kernel panic at shutdown or
device removal time.
Fixes: 4120f8d158 ("mtd: spi-nor: Use the spi_mem_xx() API")
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com> on R8A7791 Porter
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem_xxx() API has been introduced to replace the
spi_flash_read() one. Make use of it so we can get rid of
spi_flash_read().
Note that using spi_mem_xx() also simplifies the code because this API
takes care of using the regular spi_sync() interface when the optimized
->mem_ops interface is not implemented by the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Restore the status to be compatible with legacy devices.
Take Freescale eSPI boot for example, it copies (in 3 Byte
addressing mode) the RCW and bootloader images from SPI flash
without firing a reset signal previously, so the reboot command
will fail without resetting the addressing mode of SPI flash.
This patch implements .shutdown function to restore the status
in reboot process, and add the same operation to the .remove
function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Add Everspin mr25h128 16KB MRAM to the list of supported chips.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Before this patch, m25p80_read() supported few SPI protocols:
- regular SPI 1-1-1
- SPI Dual Output 1-1-2
- SPI Quad Output 1-1-4
On the other hand, m25p80_write() only supported SPI 1-1-1.
This patch updates both m25p80_read() and m25p80_write() functions to let
them support SPI 1-2-2 and SPI 1-4-4 protocols for Fast Read and Page
Program SPI commands.
It adopts a conservative approach to avoid regressions. Hence the new
implementations try to be as close as possible to the old implementations,
so the main differences are:
- the tx_nbits values now being set properly for the spi_transfer
structures carrying the (op code + address/dummy) bytes
- and the spi_transfer structure being split into 2 spi_transfer
structures when the numbers of I/O lines are different for op code and
for address/dummy byte transfers on the SPI bus.
Besides, the current spi-nor framework supports neither the SPI 2-2-2 nor
the SPI 4-4-4 protocols. So, for now, we don't need to update the
m25p80_{read|write}_reg() functions as SPI 1-1-1 is the only one possible
protocol.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
The MR25 family doesn't support JEDEC, so they need explicit mentioning
in the list of supported spi IDs. This makes it possible to add these
using for example:
compatible = "everspin,mr25h40";
There was already an entry for mr25h256. Move that one out of the "keep
for compatibility" section and put in a new group for Everspin MRAMs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Consider a message size limit when calculating the maximum amount
of data that can be read.
The message size limit has been introduced with 4.9, so cc it
to stable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Take into account transfer size limitation of SPI master.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Do not pass retlen to hardware driver read/write functions. Update it in
spi-nor generic driver instead.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Add checking of SPI transfer errors and return them from read/write
functions. Also return the amount of data transferred.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Change the return value of spi-nor device read and write methods to
allow returning amount of data transferred and errors as
read(2)/write(2) does.
Also, start handling positive returns in spi_nor_read(), since we want
to convert drivers to start returning the read-length both via *retlen
and the return code. (We don't need to do the same transition process
for spi_nor_write(), since ->write() didn't used to have a return code
at all.)
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Certain SPI controllers may provide accelerated hardware interface to
read from m25p80 type flash devices in order to provide better read
performance. SPI core supports such devices with spi_flash_read() API.
Call spi_flash_read(), if supported, to make use of such interface.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[Brian: add memset()]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I overlooked a few comments in commit 8947e396a8 ("Documentation: dt:
mtd: replace "nor-jedec" binding with "jedec, spi-nor""). Fix these up
now.
Suggested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Commit 4316302292 ("mtd: m25p80: allow arbitrary OF matching for
"jedec,spi-nor"") moved the "jedec,spi-nor" handling from the
spi_device_id table to the of_match_table, to better handle matching
complex device tree compatible strings. With that patch, device tree
support works as expected when m25p80.c is built into the kernel.
However, that commit ignored the fact that:
(1) (non-DT) platform devices might want to use the "spi-nor" string
for matching with this driver, rather than picking an arbitrary one
like "m25p80"
(2) the core SPI uevent/modalias code doesn't yet support kernel module
autoloading via of_match_table strings; so for DT-based devices, it
will only report (part of) the first compatible string used
Problem (1) has been reported previously, and I forgot to patch it up
afterward.
Problem (2) was noticed recently here:
http://lists.infradead.org/pipermail/linux-mtd/2015-October/062369.htmlhttps://lkml.org/lkml/2015/11/12/574
Specifically, this patch fixes m25p80.ko module autoloading for cases
like this:
flash@xxx {
compatible = "jedec,spi-nor";
...
};
because modalias of "spi:spi-nor" (the only module loading info provided
by the SPI core for this device) will now be listed as an alias in
m25p80.ko.
Notably, it does *not* help cases like this:
flash@xxx {
compatible = "vendor,shiny-new-device", "jedec,spi-nor";
...
};
unless we also list "shiny-new-device" in m25p_ids[]. There has been
discussion on future work for this issue here:
https://lkml.org/lkml/2015/11/12/574
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Now that the SPI-NOR/MTD framework pass the 'flash_node' through to the
partition parsing code, we don't have to do it ourselves.
Also convert to mtd_device_register(), since we don't need the 2nd and
3rd parameters anymore.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Used semantic patch with 'make coccicheck MODE=patch COCCI=script.cocci':
---8<----
virtual patch
@@
struct spi_nor b;
struct spi_nor *c;
expression d;
@@
(
-(b).flash_node = (d)
+spi_nor_set_flash_node(&b, d)
|
-(c)->flash_node = (d)
+spi_nor_set_flash_node(c, d)
)
---8<----
And a manual conversion for the one use of spi_nor_get_flash_node().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Core
* WARN (in some cases) when a struct mtd_info is registered multiple times;
in the past this was "supported", but it's still error prone for future
development. There's only one ugly case of this left in the tree (that
we're aware of) and the owners are aware of the problems there.
* fix potential deadlock in the blkdev removal path
NOTE: the (potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
* ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user space
vs. 64-bit kernel space
* Set MTD parent device correctly throughout the tree, so the tree structure
appears correctly in sysfs; many drivers were missing this (soft)
requirement
* Move device tree partitions (ofpart) into a dedicated 'partitions' subnode;
this helps to disambiguate whether a node is a partition or some other
auxiliary data
* Improve error handling for partitioning failures
NAND
* General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
* Fix OF-based autoloading of several NAND drivers when built as modules
* pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
* brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND chips)
* sunxi_nand: refactoring and a few bug fixes
* vf610: new NAND driver
* FSMC: add SW BCH support; support common NAND DT bindings
* lpc32xx_slc: refactor and improve timing calculations logic
* denali: support for rev 5.1
SPI NOR
* Layering improvements
* Added Winbond lock/unlock support
* Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
* Increase full-chip-erase timeout linearly with flash size
* fsl-quadspi: fix compile for non-ARM architectures
* New flash support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UzSW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Core:
- WARN (in some cases) when a struct mtd_info is registered multiple
times; in the past this was "supported", but it's still error prone
for future development. There's only one ugly case of this left in
the tree (that we're aware of) and the owners are aware of the
problems there.
- fix potential deadlock in the blkdev removal path NOTE: the
(potential) deadlock was introduced in a for-stable patch. This
one is also marked for -stable.
- ioctl(BLKPG) compat_ioctl support; resolves issues with 32-bit user
space vs 64-bit kernel space
- Set MTD parent device correctly throughout the tree, so the tree
structure appears correctly in sysfs; many drivers were missing
this (soft) requirement
- Move device tree partitions (ofpart) into a dedicated 'partitions'
subnode; this helps to disambiguate whether a node is a partition
or some other auxiliary data
- Improve error handling for partitioning failures
NAND:
- General: Increase timeout period, for corner-case systems with
less-than-accurate jiffies
- Fix OF-based autoloading of several NAND drivers when built as
modules
- pxa3xx_nand:
- Rework timing configuration to be more dynamic
- Refactor PM support
- brcmnand: prepare for NorthStar 2 support (ARM64, 16-bit NAND
chips)
- sunxi_nand: refactoring and a few bug fixes
- vf610: new NAND driver
- FSMC: add SW BCH support; support common NAND DT bindings
- lpc32xx_slc: refactor and improve timing calculations logic
- denali: support for rev 5.1
SPI NOR:
- Layering improvements
- Added Winbond lock/unlock support
- Added mtd_is_locked() (i.e., ioctl(MEMISLOCKED)) support
- Increase full-chip-erase timeout linearly with flash size
- fsl-quadspi: fix compile for non-ARM architectures
- New flash support"
* tag 'for-linus-20151106' of git://git.infradead.org/linux-mtd: (169 commits)
mtd: don't WARN about overloaded users of mtd->reboot_notifier.notifier_call
mtd: nand: sunxi: avoid retrieving data before ECC pass
mtd: nand: sunxi: fix sunxi_nfc_hw_ecc_read/write_chunk()
mtd: blkdevs: fix potential deadlock + lockdep warnings
mtd: ofpart: move ofpart partitions to a dedicated dt node
doc: dt: mtd: support partitions in a special 'partitions' subnode
mtd: brcmnand: Force 8bit mode before doing nand_scan_ident()
mtd: brcmnand: factor out CFG and CFG_EXT bitfields
mtd: mtdpart: Do not fail mtd probe when parsing partitions fails
mtd: fsl-quadspi: fix macro collision problems with READ/WRITE
mtd: warn when registering the same master many times
mtd: fixup corner case error handling in mtd_device_parse_register()
mtd: tests: Replace timeval with ktime_t
mtd: fsmc_nand: Add BCH4 SW ECC support for SPEAr600
mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper
mtd: nand: increase ready wait timeout and report timeouts
mtd: docg3: off by one in doc_register_sysfs()
mtd: pxa3xx_nand: clean up the pxa3xx timings
mtd: pxa3xx_nand: rework flash detection and timing setup
mtd: pxa3xx_nand: add helpers to setup the timings
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'write_enable' argument is unused and unneeded, so remove it from
the API.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Han Xu <han.xu@freescale.com>
[Brian: fixed for nxp-spifi.c]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The problem this patch is trying to address is such, that SPI NOR flash
devices attached to a dedicated SPI NOR controller cannot read their
properties from the associated struct device_node.
A couple of facts first:
1) Each SPI NOR flash has a struct spi_nor associated with it.
2) Each SPI NOR flash has certain device properties associated
with it, for example the OF property 'm25p,fast-read' is a
good pick. These properties are used by the SPI NOR core to
select which opcodes are sent to such SPI NOR flash. These
properties are coming from spi_nor .dev->of_node .
The problem is, that for SPI NOR controllers, the struct spi_nor .dev
element points to the struct device of the SPI NOR controller, not the
SPI NOR flash. Therefore, the associated dev->of_node also is the
one of the controller and therefore the SPI NOR core code is trying to
parse the SPI NOR controller's properties, not the properties of the
SPI NOR flash.
Note: The m25p80 driver is not affected, because the controller and
the flash are the same device, so the associated device_node
of the controller and the flash are the same.
This patch adjusts the SPI NOR core such that the device_node is not
picked from spi_nor .dev directly, but from a new separate spi_nor
.flash_node element. This let's the SPI NOR controller drivers set up
a different spi_nor .flash_node element for each SPI NOR flash.
This patch also fixes the controller drivers to be compatible with
this modification and correctly set the spi_nor .flash_node element.
This patch is inspired by 5844feeaa4
mtd: nand: add common DT init code
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This reflects the proper layering, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Layering suggests that the SPI NOR layer (not the hardware driver)
should be initializing the MTD layer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:
// Option (a), modalias = "spi-nor"
compatible = "jedec,spi-nor";
// Option (b), modalias = "spi-nor"
compatible = "idontknowwhatimdoing,spi-nor";
But the following would not:
// Option (c), modalias = "shinynewdevice"
compatible = "myvendor,shinynewdevice", "jedec,spi-nor";
So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).
To do this, we
(1) always (for devices without specific platform data) pass the
modalias to the spi-nor library;
(2) rework the spi-nor library to not reject "bad" names, and
instead just fall back to autodetection; and
(3) add the .of_match_table to properly catch all "jedec,spi-nor".
This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding"), we added a generic "nor-jedec" binding to catch all
mostly-compatible SPI NOR flash which can be detected via the READ ID
opcode (0x9F). This was discussed and reviewed at the time, however
objections have come up since then as part of this discussion:
http://lkml.kernel.org/g/20150511224646.GJ32500@ld-irv-0074
It seems the parties involved agree that "jedec,spi-nor" does a better
job of capturing the fact that this is SPI-specific, not just any NOR
flash.
This binding was only merged for v4.1-rc1, so it's still OK to change
the naming.
At the same time, let's move the documentation to a better name.
Next up: stop referring to code (drivers/mtd/devices/m25p80.c) from the
documentation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
We had many entries that were recently added just to allow selecting
some flashes directly but were never used. They weren't providing any
special flash handling, we just needed them due to the lack of some
generic binding string.
With the introduction of "nor-jedec" (in 1103b85) they won't be needed
unless we discover some faulty flash requiring workarounds.
As explained in m25p80 DT documentation we require specifying
"nor-jedec" now as less specific compatible entry.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the new 'nor-jedec' binding to provide automatic detection of flash
that use the 0x9F READ ID opcode. This can help for use cases where
platforms just specify compatibility with "m25p80", and then see
messages like this:
m25p80 spi32766.0: found s25fl256s1, expected m25p80
Instead, they can just specify the generic string and see this:
m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)
Also, update the language about m25p_ids[] to straighten out the
expectations here. We should no longer need to continuously grow the
m25p_ids[] table, and in fact, we might want to start removing entries
which are not used in device trees so far, so we can just default to
auto-detection as much as possible in the future.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
write_enable() was being duplicated to both m25p80.c and fsl-quadspi.c.
But this should be handled within the spi-nor abstraction layer.
At the same time, let's add write_disable() after erasing, so we don't
leave the flash in a write-enabled state afterward.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
As stated in a5b7616c5, "mtd: m25p80,spi-nor: Fix module aliases for
m25p80", m25p_ids[] in m25p80.c needs to be kept in sync with
spi_nor_ids[] in spi-nor.c. The change here corrects a misalignment.
(We were missing m25px80 and we had a duplicate w25q128.)
Signed-off-by: Alison Chaiken <alison_chaiken@mentor.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.
This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c8352f: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812a1: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510af: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This "type" seems to be an extra hint for m25p80 about the flash. Some
archs register flash_platform_data with "name" set to "m25p80" and then
with a real flash name set in "type". It seems to be a trick specific
to the m25p80 so let's move it out of spi-nor.
Btw switch to the spi_nor_match_id instead of iterating spi_nor_ids.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 03e296f613 ("mtd: m25p80: use the SPI
nor framework") accidentally removed support for Dual SPI read transfers.
Add it back.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Use the new SPI nor framework, and rewrite the m25p80:
(0) remove all the NOR comands.
(1) change the m25p->command to an array.
(2) implement the necessary hooks, such as m25p80_read/m25p80_write.
Tested with the m25p32.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Spansion s25fl256s1 and s25fl512s support Dual SPI transfers, hence set the
M25P80_DUAL_READ flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.
While an earlier version of commit 3487a63955
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris Brezillon