Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(struct opa_port_status_rsp) + num_vls * sizeof(struct _vls_pctrs)
with:
struct_size(rsp, vls, num_vls)
and so on...
Also, notice that variable size is unnecessary, hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce a 'flags' field to create address handle callback and add a flag
that marks whether the callback is executed in an atomic context or not.
This will allow drivers to wait for completion instead of polling for it
when it is allowed.
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If a MAD packet has incorrect header information, the logic uses the reply
path to report the error. The reply path expects *resp_len to be set
prior to return. Unfortunately, *resp_len is set to 0 for this path.
This causes an incorrect response packet.
Fix by ensuring that the *resp_len is defaulted to the incoming packet
size (wc->bytes_len - sizeof(GRH)).
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
For errorinfo MAD requests, the response has a 0 port number left over
from a memset. Instead we should always set the port number in the
response.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For lid routed packets 'hop_cnt' is zero, therefore current
test is incomplete. Fix it by using local mad check for
both lid routed and direct routed MADs.
Reviewed-by: Mike Mariciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HFI's counters SendWaitCnt and SendWaitVlCnt are in units
of TXE cycle time (at 805MHz). OPA counters PortXmitWait and
PortVLXmtWait are in units of flit times.
Convert the counter values to flit units using following
conversion formula:
PortXmitWait =
SendWaitCnt * 2 * (4 /link_width) * (25 Gbps /link_speed)
PortVLXmitWait =
SendWaitVLCnt * 2 * (4 /link_width) * (25 Gbps /link_speed)
At link up or downgrade events, the link width can change. To ensure
accurate counter calculations, sample the counters after the events,
during counter requests, and then aggregate the OPA counters.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Change the slid arg to ingress_pkey_table_fail() to a full
32Bits and do not convert to 16Bits in caller. This is so we
can keep everything 32bit in the kernel and only change to
16bit at the uapi boundary.
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When the driver is loaded it sets the default CCTI value to be 0. When the FM
starts and CCA is disabled the driver sets the max value to 65535 due the driver
subtracting 1 from 0 and the fact that the CCTI value is a u16.
Special case the subtraction to find the index for a 0 value.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is invalid to change Link state from Init to Armed if
IsSmConfigurationStarted bit is not set in Attribute modifier
for Set subnet management method in case of PortInfo
and PortStateInfo attribute.
Set response MAD status field bits accordingly to react correctly
in such situations and avoid changing Link state.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Grzegorz Morys <grzegorz.morys@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The "2 * UINT_MAX" statement:
if ((u64)(ts - cce->timestamp) > 2 * UINT_MAX) {
is equivalent to:
if ((u64)(ts - cce->timestamp) > UINT_MAX - 1) {
This results in a premature timeout of the cong log entry.
Fix by using unsigned 64 bit integers, removing casts, and using
an algebraic equivalent test to avoid the "2 * UINT_MAX" issue.
Also make use of kernel API to get nanoseconds instead of
open coding.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These are the use-cases where the pkey needs to be tested to see
if a packet needs to be dropped.
a) Check if pkey is not FULL_MGMT_P_KEY or LIM_MGMT_P_KEY,
drop the packet as it's not part of the management partition.
Self-originated packets are an exception.
b) If pkey index points to FULL_MGMT_P_KEY and LIM_MGMT_P_KEY is
in the table, the packet is coming from a management node,
and the receiving node is also a management node, so it is safe
for the packet to go through.
c) If pkey index points to FULL_MGMT_P_KEY and LIM_MGMT_P_KEY is
NOT in the table, drop the packet as LIM_MGMT_P_KEY should
always be in the pkey table. It could be a misconfiguration.
d) If pkey index points to LIM_MGMT_P_KEY and FULL_MGMT_P_KEY is
NOT in the table, it is safe for the packet to go through
since a non-management node is talking to another non-managment
node.
e) If pkey index points to LIM_MGMT_P_KEY and FULL_MGMT_P_KEY is in
the table, drop the packet because a non-management node is
talking to a management node, and it could be an attack.
For the implementation, these rules can be simplied to only checking
for (a) and (e). There's no need to check for rule (b) as
the packet doesn't need to be dropped. Rule (c) is not possible in
the driver as LIM_MGMT_P_KEY is always in the pkey table.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/hw/cxgb4/cm.c
drivers/infiniband/hw/qib/qib_driver.c
drivers/infiniband/hw/qib/qib_mad.c
There were minor fixups needed in these files. Just minor context diffs
due to patches from independent sources touching the same basic area.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Do not track physical state separately from host_link_state.
Deduce physical state from host_link_state when required.
Change cache_physical_state to log_physical_state to make
sure host_link_state reflects hardwares physical state properly.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The macro size is valid. This change makes it less ambiguous.
Bounds check trap type for better security.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Trivial fix to spelling mistake in pr_warn_ratelimited warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Increase lid used in hfi1 driver to 32 bits. qib continues
to use 16 bit lids.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add 16B bypass packet support for UD traffic types.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rvt_check_ah() delegates lid verification to underlying
driver. Underlying driver uses different conditions to
check for dlid depending on whether the device supports
extended LIDs
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Do not track logical state separately from host_link_state. Deduce
logical state from host_link_state when required. Transitions in
set_link_state and goto_offline already make sure host_link_state
reflects hardware's logical state properly.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch series primarily increases sizes of variables that hold
lid values from 16 to 32 bits. Additionally, it adds a check in
the IB mad stack to verify a properly formatted MAD when OPA
extended LIDs are used.
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Both add new code
include/rdma/ib_verbs.h - Both add new code
Signed-off-by: Doug Ledford <dledford@redhat.com>
slid field in struct ib_wc is increased to 32 bits.
This enables core components to use larger LIDs if needed.
The user ABI is unchanged and return 16 bit values when queried.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A trap should be sent to the FM until the FM sends a repress message.
This is in line with the IBTA 13.4.9.
Add the ability to resend traps until a repress message is received.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael N. Henry <michael.n.henry@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
According to IBTA spec a QKey violation should not result in a bad qkey
trap being triggered for UD queue pairs. Also since it is a silent error
we do not increment the q_key violation or the dropped packet counters.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure states returned to the Fabric Manager are consistent with
the OPA specification by caching the physical state along with the
logical state.
Reviewed-by: Stuart Summers <john.s.summers@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrzej Kotlowski <andrzej.kotlowski@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Improve safety of code by checking the size of the data buffer and
prevent buffer overrun
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Neel Desai <neel.desai@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Provide the ability for IB clients to modify the OPA specific
capability mask and include this mask in the subsequent trap data.
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Michael N. Henry <michael.n.henry@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify core and driver components to use accessor functions
introduced to access individual fields of rdma_ah_attr
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Both opa_vnic and the hfi driver use the same opa_classport_info
definition. We will also have ib_sa capable of querying opa class
port info and would need this definition. Move it to ib_mad.h
for everyone to use.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ingress and egress port P_Key checking should always be performed for
HFIs. This patch will enable ingress and egress P_Key checking when
the port is initialized and will ignore the P_Key information sent by
the FM in the port info structure which is meant to be used only by the
switch.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Neel Desai <neel.desai@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
VL15 in the SC2VL table is used to indicate an invalid SC
for the FM, however, internally the driver remaps SCs from
VL15 to ILLEGAL_VL to prevent error counts. This mapping
confuses the FM when performing a sweep, making it return
a table mismatch error. Have SMA convert ILLEGAL_VL
to VL15 entries for the SC2VL table queries.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FM uses the values of MulticastMask and CollectiveMask to
determine the number of bits for net masks. The current values of
0 and 0 are incorrect. The values should be 4 and 1. Updated the
necessary code to reflect the specified values.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
HFI1 HW specific support for VNIC functionality.
Dynamically allocate a set of contexts for VNIC when the first vnic
port is instantiated. Allocate VNIC contexts from user contexts pool
and return them back to the same pool while freeing up. Set aside
enough MSI-X interrupts for VNIC contexts and assign them when the
contexts are allocated. On the receive side, use an RSM rule to
spread TCP/UDP streams among VNIC contexts.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Prepare for removal of ib_device.dma_device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
and rename class version define to indicate SM rather than SMP or SMI
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch consolidates the node GUIDs and the port GUID handling
and unifies access to these items. The knowledge of hfi1 GUIDs'
design and their location are kept in accessors to centralize access.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FM should have full control to set the pkeys in the
driver pkey table. Remove filtering done by the driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All calls to tune_serdes and start_link are paired. Move
tune_serdes inside start_link.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(u64)' which is 8.
It is likely that the number of bits of 'port_mask' was expected here.
Use sizeof() * 8 to get the correct number.
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In all other places in this file where 'find_first_bit' is called,
port_num is defined as a 'u8' and no casting is done.
Do the same here in order to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver does not check if the CableInfo query is supported for the
port type. Return early if CableInfo is not supported for the port type,
making compliance with the specification explicit and preventing lower
level code from potentially doing the wrong thing if the query is not
supported for the hardware implementation.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fixes the following warnings with PROVE_LOCKING and PROVE_RCU
enabled in the kernel:
case (1):
[ INFO: suspicious RCU usage. ]
drivers/infiniband/hw/hfi1/init.c:532
suspicious rcu_dereference_check() usage!
case (2):
[ INFO: suspicious RCU usage. ]
drivers/infiniband/hw/hfi1/hfi.h:1624
suspicious rcu_dereference_check() usage!
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny