If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-14-git-send-email-imre.deak@intel.com
The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-11-git-send-email-imre.deak@intel.com
For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-4-git-send-email-imre.deak@intel.com
Bspec is confused w.r.t. the HSW/BDW FDI disable sequence. It lists
FDI RX disable both as step 13 and step 18 in the sequence. But I dug
up an old BUN mail from Art that moved the FDI RX disable to happen
before DDI_BUF_CTL disable. That BUN did not renumber the steps and just
added a note:
"Workaround: Disable PCH FDI Receiver before disabling DDI_BUF_CTL."
The BUN described the symptoms of the fixed issue as:
"PCH display underflow and a black screen on the analog CRT port that
happened after a FDI re-train"
I suppose later someone tried to renumber the steps to match, but forgot
to remove the FDI RX disable from its old position in the sequence.
They also forgot to update the note describing what should be done in
case of an FDI training failure. Currently it says:
"To retry FDI training, follow the Disable Sequence steps to Disable FDI,
but skip the steps related to clocks and PLLs (16, 19, and 20), ..."
It should really say "17, 20, and 21" with the current sequence because
those are the steps that deal with PLLs and whatnot, after step 13 became
FDI RX disable. And had the step 18 FDI RX disable been removed, as I
suspect it should have, the note should actually say "17, 19, and 20".
So, let's move the FDI RX disable to happen before DDI_BUF_CTL disable,
as that would appear to be the correct order based on the BUN.
Note that Art has since unconfused the spec, and so this patch should
now match the steps listed in the spec.
v2: Add a note that the spec is now correct
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456841783-4779-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
According to the BSpec update, bit 7 of PORT_CL1CM_DW0 register needs to be
checked to ensure that the register is in accessible state.
Also, based on a BSpec update, changing the timeout value to
check iphypwrgood, from 10ms to wait for up to 100us.
v2: [Ville] use wait_for_us instead of the atomic call.
v3: [Jani/Imre] read register only once
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reported-by: Philippe Lecluse <Philippe.Lecluse@intel.com>
Cc: Deak, Imre <imre.deak@intel.com>
Cc: Nikula, Jani <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459446354-19012-1-git-send-email-vandana.kannan@intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Include DPLL0 in the managed dplls for SKL/KBL. While it has to be kept
enabled because of it driving CDCLK, it is better to special case that
inside the DPLL code than in the higher level.
v2: Use INTEL_DPLL_ALWAYS_ON flag. (Ander)
v3: Remove extremely paranoid WARN_ONs. (Maarten)
Handle DPLL0 in skylake_get_ddi_pll() properly. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-14-git-send-email-ander.conselvan.de.oliveira@intel.com
Manage the LCPLLs used with DisplayPort, so that all the HSW/BDW DPLLs
are managed by the shared dpll code.
v2: Introduce INTEL_DPLL_ALWAYS_ON flag to please state checker. (Ander)
v3: Initialize pll->flags in intel_shared_dpll_init(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Move the code for selecting and configuring HSW/BDW DDI PLLs into the
shared dpll infrastructure. With this most of the PLL selection logic
for those platforms is in one place. DisplayPort is handled separately,
but that should be fixed on a follow up patch. It also allows a small
clean up of the SPLL logic.
v2: Rebase.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-10-git-send-email-ander.conselvan.de.oliveira@intel.com
Change the type of intel_crtc_state->shared_dpll to be a pointer to a
shared dpll. With this there is no need to first convert the id stored
in the crtc state to a pointer in order to use it. It does introduce a
bit of hassle on doing the opposite.
The long term objective is to hide details about dpll ids behind the
shared dpll interface.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-5-git-send-email-ander.conselvan.de.oliveira@intel.com
The recent commit [0bdf5a0564: drm/i915: Add reverse mapping between
port and intel_encoder] introduced a reverse mapping to retrieve
intel_dig_port object from the port number. The code assumed that the
port vs intel_dig_port are 1:1 mapping. But in reality, this was a
too naive assumption.
As Martin reported about the missing HDMI audio on his SNB machine,
pre-HSW chips may have multiple intel_dig_port objects corresponding
to the same port. Since we assign the mapping statically at the init
time and the multiple objects override the map, it may not match with
the actually enabled output.
This patch tries to address the regression above. The reverse mapping
is provided basically only for the audio callbacks, so now we set /
clear the mapping dynamically at enabling and disabling HDMI/DP audio,
so that we can always track the latest and correct object
corresponding to the given port.
Fixes: 0bdf5a0564 ('drm/i915: Add reverse mapping between port and intel_encoder')
Reported-and-tested-by: Martin Kepplinger <martink@posteo.de>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456324522-21591-1-git-send-email-tiwai@suse.de
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com
In commit bfb9faab8 we added a workaround for some BXT BIOS that fail to
properly initialize the DDI_A_4_LANES bit of the control register (4
lanes is the only valid configuration on BXT since there is no DDI E to
share with). A recent patch added some additional checks on this
register bit before the workaround gets applied; this breaks eDP on BXT
in some settings. Some minor code shuffling is all we need to restore
the workaround.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 7cd87cb80 ("drm/i915: Check max number of lanes when registering DDI ports")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454022577-834-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Pull in Dave's drm-next pull request to have a clean base for 4.6.
Also, we need the various atomic state extensions Maarten recently
created.
Conflicts are just adjacent changes that all resolve to nothing in git
diff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
commit 10afa0b65f ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL")
added sanity checks to make sure we don't end up with too many ddi translation
values for eDP ports, but it actually failed to check if the port is eDP.
We still look up the edp translations for non-eDP ports, but don't use
them, so we shouldn't be complaining about them either.
Fixes: 10afa0b65f ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452612496-9201-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the ddi buffer programming code a bit more neat by passing
around dev_priv instead of dev.
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
skl_get_buf_trans_edp() effectively contains another copy of
skl_get_buf_trans_dp(). Remove the duplication and just call
skl_get_buf_trans_dp() from skl_get_buf_trans_edp().
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
skl_get_buf_trans_*() don't need the 'ddi_translations' local variable
since all they with is assign and return. Just return the right thing
directly and get rid of the local variable.
v2: Resolve conflicts due to KBL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Rather than having open coded checks for the DDI A/E configuration,
just store the max supported lane count in intel_digital_port.
We had an open coded check for DDI A, but not for DDI E. So we may
have been vilating the DDI E max lane count.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
That state the obvious and just duplicate the place we
need to change whenever the table is updated. So let's clean it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452021535-22641-1-git-send-email-rodrigo.vivi@intel.com
When debuging an intermittent corrupted screen I suspected on DDI
translation table and checked we are out of date with the spec.
I'm not sure this will fix my bug yet, but it is always good to follow
the spec.
v2: Ville caught a switched i-boost value. Thanks!
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452021087-21673-1-git-send-email-rodrigo.vivi@intel.com
- fix atomic watermark recomputation logic (Maarten)
- modeset sequence fixes for LPT (Ville)
- more kbl enabling&prep work (Rodrigo, Wayne)
- first bits for mst audio
- page dirty tracking fixes from Dave Gordon
- new get_eld hook from Takashi, also included in the sound tree
- fixup cursor handling when placed at address 0 (Ville)
- refactor VBT parsing code (Jani)
- rpm wakelock debug infrastructure ( Imre)
- fbdev is pinned again (Chris)
- tune the busywait logic to avoid wasting cpu cycles (Chris)
* tag 'drm-intel-next-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20151218
drm/i915/skl: Default to noncoherent access up to F0
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: don't enable autosuspend on platforms without RPM support
drm/i915/backlight: prefer dev_priv over dev pointer
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Pin the ifbdev for the info->system_base GGTT mmapping
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: mdelay(10) considered harmful
drm/i915: check that we are in an RPM atomic section in GGTT PTE updaters
drm/i915: add support for checking RPM atomic sections
drm/i915: check that we hold an RPM wakelock ref before we put it
drm/i915: add support for checking if we hold an RPM reference
drm/i915: use assert_rpm_wakelock_held instead of opencoding it
drm/i915: add assert_rpm_wakelock_held helper
drm/i915: remove HAS_RUNTIME_PM check from RPM get/put/assert helpers
drm/i915: get a permanent RPM reference on platforms w/o RPM support
drm/i915: refactor RPM disabling due to RC6 being disabled
...
This is the "fix igt basic test set issues" edition.
- more PSR fixes from Rodrigo, getting closer
- tons of fifo underrun fixes from Ville
- runtime pm fixes from Imre, Daniel Stone
- fix SDE interrupt handling properly (Jani Nikula)
- hsw/bdw fdi modeset sequence fixes (Ville)
- "don't register bad VGA connectors and fall over" fixes (Ville)
- more fbc fixes from Paulo
- and a grand total of exactly one feature item: Implement dma-buf/fence based
cross-driver sync in the i915 pageflip path (Alex Goins)
* tag 'drm-intel-next-2015-12-04-1' of git://anongit.freedesktop.org/drm-intel: (70 commits)
drm/i915: Update DRIVER_DATE to 20151204
drm/i915/skl: Add SKL GT4 PCI IDs
Revert "drm/i915: Extend LRC pinning to cover GPU context writeback"
drm/i915: Correct the Ref clock value for BXT
drm/i915: Restore skl_gt3 device info
drm/i915: Fix RPS pointer passed from wait_ioctl to i915_wait_request
Revert "drm/i915: Remove superfluous NULL check"
drm/i915: Clean up device info structure definitions
drm/i915: Remove superfluous NULL check
drm/i915: Handle cdclk limits on broadwell.
i915: wait for fence in prepare_plane_fb
i915: wait for fence in mmio_flip_work_func
drm/i915: Extend LRC pinning to cover GPU context writeback
drm/i915/guc: Clean up locks in GuC
drm/i915: only recompress FBC after flushing a drawing operation
drm/i915: get rid of FBC {,de}activation messages
drm/i915: kill fbc.uncompressed_size
drm/i915: use a single intel_fbc_work struct
drm/i915: check for FBC planes in the same place as the pipes
drm/i915: alloc/free the FBC CFB during enable/disable
...
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' of tiwai/sound into drm-intel-next-queued
Add get_eld audio component for i915/HD-audio
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
This patch adds a reverse mapping from a digital port number to
intel_encoder object containing the corresponding intel_digital_port.
It simplifies the query of the encoder a lot.
Note that, even if it's a valid digital port, the dig_port_map[] might
point still to NULL -- usually it implies a DP MST port. Due to this
fact, the NULL check in each place has no WARN_ON() and just skips the
port. Once when the situation changes in future, we might introduce
WARN_ON() for a more strict check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
Let's introduce ULT and ULX Kabylake definitions and start
using it for a propper DDI buffer translation.
v2: Remove extra white space. (Paulo)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Currently we disable some parts of FDI setup after a failed link
training. But despite that we continue with the modeset as if everything
is fine. This results in tons of noise from the state checker, and
it means we're not following the proper modeset sequence for the rest of
crtc enabling, nor for crtc disabling.
Ideally we should abort the modeset and follow the proper disable
sequence to shut off everything we enabled so far, but that would
require a big rework of the modeset code. So instead just leave FDI
up and running in its untrained state, and log an error. This is
what we do on older platforms too.
v2: Fix a typo in the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260570-14670-1-git-send-email-ville.syrjala@linux.intel.com
The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.
I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.
While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
