Another version of Elgato EyeTV Sat USB DVB-S2 adapter needs just
a USB ID addition.
Signed-off-by: Christian Knippel <namerp@gmail.com>
Reported-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, dw2102 assumes that the USB IDs will be either at
an external header or defined internally. That doesn't sound
right.
So, let's move the definitions to just one place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The test for the return code was mistakenly inverted. This caused DVB
devices with CA module to fail on modprobe.
Tested with TechnoTrend CT2-4650 CI USB tuner.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change dvb frontend to check if tuner is free when device opened in RW
mode.
Call to enable_source handler either returns with an active pipeline to
tuner or error if tuner is busy.
Tuner is released when frontend is released calling the disable_source
handler.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GET_FRONTEND and G_PROPERTY can be called anytime, even when the
tuner/demod is not fully locked. However, several parameters
returned by those calls are available only after the demod get
VITERBI lock.
While several drivers do the right thing by checking the status before
returning the parameter, some drivers simply blindly update the
DTV properties cache without checking if the registers at the
hardware contain valid values.
Due to that, programs that call G_PROPERTY (or GET_FRONTEND)
before having a tuner lock may interfere at the zigzag logic,
as the DVB kthread calls the set_frontend() callback several
times, to fine tune the frequency and to identify if the signal
is inverted or not.
While the drivers should be fixed to report the right status,
we should prevent that such bugs would actually interfere at the
device operation.
So, let's use a separate var for userspace calls to get frontend.
As we copy the content of the cache, this should not cause any
troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using the DTV properties cache directly, pass the get
frontend data as an argument. For now, everything should remain
the same, but the next patch will prevent get_frontend to
affect the global cache.
This is needed because several drivers don't care enough to only
change the properties if locked. Due to that, calling
G_PROPERTY before locking on those drivers will make them to
never lock. Ok, those drivers are crap and should never be
merged like that, but the core should not rely that the drivers
would be doing the right thing.
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of implicitly using the DTV cache properties at
dtv_get_frontend(), pass it as an additional argument.
This patch prepares to use a separate cache for G_PROPERTY,
in order to avoid it to mangle with the DVB thread
zigzag logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When debugging troubles with DTV properties get/set, it is
important to be able to see not only the properties from get, but
also the ones from set. So, improve the dumps to allow reporting
both.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from ktime_get_real is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
[mchehab@osg.samsung.com: fix trivial merge conflicts]
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The space is missing after ',', and this will be introduce much
noise when checking new patch around them.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since the number of elements equals to 1, so just use kzalloc to
simplify the code and make it more readable.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The parentheses are not required after return, and just remove it.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new product id to dvb-usb-dvbsky for new version of TechnoTrend CT2-4650 CI
Signed-off-by: Torbjörn Jansson <torbjorn.jansson@mbox200.swipnet.se>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The output of a tuner is not only IF frequencies. They may also
output audio on some of its pins, and may even be a zero-IF tuner,
with outputs a baseband. So, rename the PAD name to make it
clearer and add a proper documentation about that at tuner.h.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MyGica/Geniatech S2870 is very similar to the S870 but with dual tuner. The card is recognised as Geniatech STK8096-PVR.
[mchehab@osg.samsung.com: Fix some checkpatch.pl issues]
Signed-off-by: Nicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While mxl111sf may have multiple frontends, it has just one
tuner. Reflect that on the media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices like mxl111sf-based WinTV Aero-m have multiple
frontends, all linked on the same demod. Currently, the
dvb_create_graph() function is not smart enough to create
multiple links. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several pure digital TV devices have a frontend with the tuner
integrated on it. Add the RF connector when dvb_create_media_graph()
is called on such devices.
Tested with siano and dvb_usb_mxl111sf drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those functions are used only if CONFIG_MEDIA_CONTROLLER_DVB.
Without that, if !CONFIG_MEDIA_CONTROLLER_DVB, it would produce
two warnings:
drivers/media/dvb-core/dvbdev.c:219:12: warning: 'dvb_create_tsout_entity' defined but not used [-Wunused-function]
static int dvb_create_tsout_entity(struct dvb_device *dvbdev,
^
drivers/media/dvb-core/dvbdev.c:264:12: warning: 'dvb_create_media_entity' defined but not used [-Wunused-function]
static int dvb_create_media_entity(struct dvb_device *dvbdev,
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller next gen patchset added several new fields
to be used with it. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not be creating device nodes at IRQ contexts. So,
the only flags we'll be using will be GFP_KERNEL. Let's
remove the gfp_flags, in order to make the interface simpler.
If we ever need it, it would be easy to revert those changes.
While here, remove an extra blank line.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Indirect links are those whose interface indirectly controls
other functions.
There are two interfaces that have indirect controls at the DVB
side:
- the network interface, which also controls the demux;
- the DVR interface which also controls the demux.
One could argue that the frontend control to the tuner is indirect.
Well, that's debatable. There's no way to create subdev interfaces
for tuner and demod, as those devices are tightly coupled. So, it
was decided that just one interface is the best to control both
entities, and there's no plan (or easy way) to decouple both. So,
the DVB frontend interface should link to both entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cleanup the code a little bit by moving the routine that creates
links between DVR and demux to the I/O entitis into a separate
function.
While here, fix the code to use strncmp() instead of strcmp().
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media controller is enabled and mdev is filled, it should
ensure that the media graph will be properly initialized.
Enforce that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, if something gets wrong at dvb_create_media_entity()
or at dvb_create_media_graph(), the device will still be
registered.
Change the logic to properly handle it and free all media graph
objects if something goes wrong at dvb_register_device().
Also, change the logic at dvb_create_media_graph() to return
an error code if something goes wrong. It is up to the
caller to implement the right logic and to call
dvb_unregister_device() to unregister the already-created
objects.
While here, add a missing logic to unregister the created
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links are normally enabled, meaning that the interfaces are
bound to the entities. So, any ioctl sent to the interface are reflected
at the entities managed by the interface.
However, when a device is in use, other interfaces for the same hardware
could be decoupled from the entities linked to them, because the
hardware may have some parts busy.
That's for example, what happens when an hybrid TV device is in use.
If it is streaming analog TV or capturing signals from S-Video/Composite
connectors, typically the digital part of the hardware can't be used and
vice-versa.
This is generally due to some internal hardware or firmware limitation,
that it is not easily mapped via data pipelines.
What the Kernel drivers do internally is that they decouple the hardware
from the interface. So, all changes, if allowed, are done only at some
interface cache, but not physically changed at the hardware.
The usage is similar to the usage of the MEDIA_LNK_FL_ENABLED on data
links. So, let's use the same flag to indicate if either the interface
to entity link is bound/enabled or not.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners actually have at least one connector on its input.
Add a PAD to connect it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like we do with entities, use a similar macro for the
interfaces loop.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller New Generation redefines the types for both
interfaces and entities to be used on DVB. Make the needed
changes at the DVB core for all interfaces, entities and
data and interface links to appear in the graph.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces got created, we need to fix the entity
namespace.
So, let's create a consistent new namespace and add backward
compatibility macros to keep the old namespace preserved.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some interfaces indirectly control multiple entities.
Add support for those.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the infrastruct for that is set, add support for
interfaces.
Please notice that we're missing two links:
DVB FE intf -> tuner
DVB demux intf -> dvr
Those should be added latter, after having the entire graph
set. With the current infrastructure, those should be added
at dvb_create_media_graph(), but it would also require some
extra core changes, to allow the function to enumerate the
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entire logic that represent graph links were developed on a
time where there were no needs to dynamic remove links. So,
although links are created/removed one by one via some
functions, they're stored as an array inside the entity struct.
As the array may grow, there's a logic inside the code that
checks if the amount of space is not enough to store
the needed links. If it isn't the core uses krealloc()
to change the size of the link, with is bad, as it
leaves the memory fragmented.
So, convert links into a list.
Also, currently, both source and sink entities need the link
at the graph traversal logic inside media_entity. So there's
a logic duplicating all links. That makes it to spend
twice the memory needed. This is not a big deal for today's
usage, where the number of links are not big.
Yet, if during the MC workshop discussions, it was said that
IIO graphs could have up to 4,000 entities. So, we may
want to remove the duplication on some future. The problem
is that it would require a separate linked list to store
the backlinks inside the entity, or to use a more complex
algorithm to do graph backlink traversal, with is something
that the current graph traversal inside the core can't cope
with. So, let's postpone a such change if/when it is actually
needed.
It should also be noticed that the media_link structure uses
44 bytes on 32-bit architectures and 84 bytes on 64-bit
architecture. It will thus be allocated out of the 64-bytes and
96-bytes pools respectively. That's a 12.5% memory waste on
64-bit architectures and 31.25% on 32-bit architecture.
A linked list is less efficient than an array in this case, but
this could later be optimized if we can get rid of the reverse
links (with would reduce memory allocation by 50%).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by Laurent Navet:
"Calling ktime_add_us() seems useless as is only useful
for it's return value which is ignored."
That's reported by coverity CID 1309761.
Laurent proposed to just remove ktime_add_us, but the fact is that
the logic of this function is broken. Instead, we need to use the
value of the timeout, and ensure that it will work on the loops
to emulate the legacy DiSEqC ioctl (FE_DISHNETWORK_SEND_LEGACY_CMD).
Please notice that the logic was also broken if, for any reason,
msleep() would sleep a little less than what it was expected, as
newdelta would be smaller than delta, and udelay() would not be called.
It should also be noticed that nobody noticed that trouble before
likely because the FE_DISHNETWORK_SEND_LEGACY_CMD is not used
anymore by modern DVB applications.
Reported-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the DVB-T/C/T2 usb stick WinTV-soloHD from
Hauppauge. It adds the usb ID 2040:0264 Hauppauge to the cards of the
driver em28xx.
I successfully tested DVB-T/C and the IR remote control with the
firmware dvb-demod-si2168-b40-01.fw.
Signed-off-by: Arno Bauernoeppel <arno@aziraphale.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.
With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.
However, when in FE_TUNE_MODE_ONESHOT this is not true.
So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improve the comments at the header, removing kernel-doc
tag from where it doesn't belong, grouping the legacy tuner
functions, and improving the text.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The get_state()/set_state and the corresponding data types
(struct tuner_state and enum tuner_param) are old DVB interfaces
that came from the DVBv3 time.
Nowadays, set_params() provide a better way to set the tuner
and demod parameters. So, no need to keep those legacy stuff,
as all drivers that were using it got converted.
With this patch, all kABI elements at dvb_frontend.h are now
documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As SEC tone and voltage could have changed during
suspend(), restore them to their previous values at
resume().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DocBook description of this header has two issues:
- It calls the Kernel ABI as API, instead of kABI;
- It mentions that the DVB frontend kABI is not described
within the document. As this will actually generate a
single DocBook, this is actually not true, now that
the documentation for the frontend was added.
So, fix both issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This header file provides the kABI functions used by the
Digital TV Frontend core support. Add a description for
this kABI, to add at the device_drivers Kernel DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Documents the most used functions at the Digital TV
kABI: dvb_frontend_register(), dvb_frontend_unregister()
and dvb_frontend_detach().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb_frontend_reinitialise() function is a special case
used by just one frontend. Document it, for completeness.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function is used mainly at the DVB core, in order to provide
emulation for a legacy ioctl. The only current exception is
the stv0299 driver, with takes more than 8ms to switch voltage,
breaking the emulation for FE_DISHNETWORK_SEND_LEGACY_CMD.
Document that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Classify the functions at the DVB core per API. That makes easier
to understand how they're related to the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is better to keep the documentation overview at the header file,
as this makes easier for developers to remember to fix when needed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While we can't document #defines, documenting enums are
well supported by kernel-doc. So, convert the bitmap defines
into an enum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The usage of #define at the kABI is fine, but it doesn't
allow adding a proper description. As those defines deserve
a proper documentation, let's convert them into an enum and
document them at device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb/kdapi.tmpl has already an extensive documentation about
this callback. Now that we've added function typedefs at kernel-doc,
add such documentation at demux.h, for it to appear at device-drivers
DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb/kdapi.tmpl has already an extensive documentation about
this callback. Now that we've added function typedefs at kernel-doc,
add such documentation at demux.h, for it to appear at device-drivers
DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are lots of CodingStyle violations here. Now that we're
touching a log on this header files, adding the documentation
here, make sure that this will follow the Kernel CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB core has a provision for other frontend sources, but no
drivers use it. The kdapi.xml contains provision for some other
frontend source types, but it is not in sync with the code.
So, remove the unused types and sync both files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This enum is not actually used anymore. The only value used from
the enum is DMX_OK, passed as a parameter on two callbacks.
Yet, this value is not used anywhere. So, just remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two callbacks still not documented:
.//drivers/media/dvb-core/demux.h:422: warning: No description found for parameter 'get_pes_pids'
.//drivers/media/dvb-core/demux.h:422: warning: No description found for parameter 'get_stc'
The purpose of first one is clear. The second one is used only
on the obsolete av7110 driver, and its purpose is not clear,
as it just returns a 64-bit word from the firmware to userspace.
Let's document get_pes_pids and mark get_stc as private, adding
a comment to not use it, while this is not documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two DVB demux callbacks and ioctls that aren't documented
and aren't used at all by the DVB core or by any DVB driver upstream.
Let's comment out the code for those two ioctls and remove on some
future version.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are a few inconsistencies between the old documentation
that got imported into the header and the current status.
Update them, and use the proper doc-nano nomenclature for
struct artuments "@", instead of foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DocBook/media/dvb/kdapi.xml contains the description of
the kABI for DVB. The problem is that, by being maintained
on a separate file and not being updated for years, it got
outdated. So, for example, some callback parameters were
changed, but the DocBook were still using the old stuff.
As a first step to fix it, let's move the documentation of
struct dmx_demux into demux.h and fix the parameters used
there.
For now, don't document any other field nor touch the
descriptions that got moved, letting this job to other
patches. That makes easier to review the patch.
PS.: Please notice that an additional patch will be needed
in order to fix the return values (some uses non-existent
return codes) and to the functions and callbacks mentioned at
the descriptions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several CodingStyle violations at the DVB code. While
we won't be fixing them as a hole, let's fix at least the
headers, as we're touching on them already in order to properly
document them.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This struct is already documented at the header file, but it is
not using Kernel doc-nano format. Convert to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds Terratec H7 Rev. 4 with USB id 0ccd:10a5 to DVBSky driver.
Signed-off-by: Erik Andresen <erik@vontaene.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two came from dvb_register_adapter cut-and-paste:
.//drivers/media/dvb-core/dvbdev.h:199: warning: Excess function parameter 'device' description in 'dvb_register_device'
.//drivers/media/dvb-core/dvbdev.h:199: warning: Excess function parameter 'adapter_nums' description in 'dvb_register_device'
Remove them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the most relevant functions and data structs for
developers that are working with the DVB subsystem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct is used on every DVB Front End driver, as it
contains what's needed to register/use a frontend at the
Kernel.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Most of the parameters here are already well defined at
the userspace documentation. Yet, it is good to add some
documentation, for the developers to be sure that they
are the same as the ones at userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This is one of the most important functions of the DVB
frontend, containing the logic needed to set the parameters
at the demux and to send commands via SEC.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The dvb_frontend.c core defines a FE_ALGO_HW symbol that it is
never used. Also, both cx24123 returns 1 to get_algo() callback
instead of using DVBFE_ALGO_HW.
Probably, those are some left overs from some code cleanup.
Let's stop returning magic numbers and use the proper macro
value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The struct dvb_tuner_ops contains lots of callbacks used
by tuners. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct inside dvb-frontend.h stores some parameters
from V4L2 API (videodev2.h), in order to be used by the
hybrid analog/digital TV tuners.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This enum is not used anymore, as drivers use the
modulation definitions from the public API. It is probably
a left over from some DVB core cleanup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Despite being used everywhere at DVB frontends, the
struct dvb_tuner_info were never documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_ringbuffer.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
While here, put multi-line comments on the right format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_math.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_frontend.h that are ready
for DocBook, although not properly formatted.
Convert them, and add this file to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some tags at dvb_ca_en50221.h, but using a
different format. Convert them, fix a few entries and add
to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are lots of docbook marks at the media subsystem, but
those aren't used.
Add the core headers/code in order to start generating docs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@eth_zero_addr@
expression e;
@@
-memset(e,0x00,ETH_ALEN);
+eth_zero_addr(e);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Quite a few of the ->diseqc_send_master_cmd() implementations don't
check cmd->msg_len so it can lead to memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct timeval uses a 32-bit seconds representation which will
overflow in the year 2038 and beyond. This patch replaces
the usage of struct timeval with ktime_t which is a 64-bit
timestamp and is year 2038 safe.
This patch is part of a larger attempt to remove all instances
of 32-bit timekeeping variables (timeval, timespec, time_t)
which are not year 2038 safe, from the kernel.
[mchehab@osg.samsung.com: add a missing parenthesis, breaking compilation]
Suggested-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.
So, let's do it.
This patch was generated by this shell script:
for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done
While here, make CodingStyle fixes on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*
Frontend bandwidth calculation overflows on very high DVB-S/S2
symbol rates. Use mult_frac() macro in order to keep calculation
correct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
Add Leadtek WinFast DTV2000DS Plus device based on Realtek RTL2832U.
I have not tested the remote, but it is the Y04G0051 model.
Signed-off-by: Christian Dale <kernel@techmunk.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ID 1b80:d3a4 Afatech
Simply added the PID (0xd3a4) of this DVB-T USB device to the list of rtl2832u-supported devices. VID (0x1b80) is same as KWORLD2.
Tested and verified to work in amd64 with kernels 3.13.0 and 3.16.0.
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions "dvb_unregister_device" and "kfree" could still be called
by the dvb_ca_en50221_init() function in the case that a previous resource
allocation failed.
* Corresponding details could be improved by adjustments for jump targets.
* Let us delete also an unnecessary check for the variable "ca" there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TechnoTrend TT-connect S2-4600 is a USB2.0 DVB-S/S2 tuner using the popular
Montage M88DS3103/M88TS2022 demod/tuner.
The demodulator needs a firmware. Antti posted a firmware when releasing
support for PCTV 461e, available here:
http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really a simple function, but using it avoids to have
if's inside the drivers.
Also, the kABI becomes a little more clearer.
This shouldn't generate any overhead, and the type check
will happen when compiling with MC DVB enabled.
So, let's do it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using media_dev argument for dvb_create_media_graph(),
use the adapter.
That allows to create a stub for this function, if compiled
without DVB support, avoiding to add extra if's at the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prefix all DVB media controller entities with "dvb-" and use dash
instead of underline at the names.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if CONFIG_MEDIA_CONTROLLER_DVB is not selected, it is now
producing this warning:
drivers/media/dvb-core/dvb_frontend.c: In function ‘dvb_frontend_thread’:
drivers/media/dvb-core/dvb_frontend.c:695:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic there tries to start the media entity even if it
doesn't exist, causing this bug:
[ 314.356162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 314.356202] IP: [<ffffffffa02ef74c>] media_entity_pipeline_start+0x1c/0x390 [media]
Reported-by: Gert-Jan van der Stroom <gjstroom@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While the DVB thread is running, the media pipeline should be
streaming. This should prevent any attempt of using the analog
TV while digital TV is working, and vice-versa.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the dvb frontend thread starts, the tuner should be switched
to the frontend. Add a code that ensures that this will happen,
using the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For now, let's keep the DVB-specific media controller links enabled
by default. On most devices, this is fixed anyway, so no big issue.
Ok, the demux actually have dynamic links based on the filters, but
we don't represent them yet, as the media controller currently lacks
the capability of dynamically create/delete entities.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to create a DVB graph, linking the several DVB devnodes.
Add such function. Please notice that this helper function
doesn't take into account devices with multiple DVB adapters
and frontends.
For devices with multiple adapters, they should either create two
different media controller instances or to improve this function
to take the adapter ID into account.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While on some devices the tuner is bound inside the frontend,
other devices use a separate subdevice for it.
So, in order to be more generic, better to map it with two
pads.
That will allows to use the media controller to lock the tuner
between the DVB and the V4L2 sub-drivers, on hybrid devices.
While here, change the logic to use pad 0 as sink for devices
with both sink and source pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We want to represent the links between the several DVB devnodes,
so let's create PADs for them.
The DVB net devnode is a different matter, as it is not related
to the media stream, but with network. So, at least for now, let's
not add any pad for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core network support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core CA support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the dvb core demux support aware of the media controller and
register the corresponding devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the dvb core is capable of registering devices via the
media controller, add support for the DVB frontend devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a way to register media controller device nodes
at the DVB core.
Please notice that the dvbdev callers also require changes
for the devices to be registered via the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the generic facility instead of a home-grown one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert dprintk to netdev_dbg where appropriate.
Remove dvb_net_debug module_param.
Remove __func__ from output as that can be added by dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need for more macros, so remove them and use the kernel extension.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
It's better to use TS_SC instead of magic number 0xC0.
[m.chehab@samsung.com: patch rebased and message rewritten, as this
patch conflicted with an already applied patch]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for IT930x USB bridge and IT9303 reference design.
It is a DVB-T/T2/C tuner with the following components:
- IT9303 USB bridge
- Si2168-B40 demodulator
- Si2147-A30 tuner
The IT9303 requires firmware that can be downloaded here:
http://trsqr.net/olli/linux/firmwares/it930x/
The Si2168-B40 requires firmware, but the one that is used by PCTV 292e can be used.
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/
The Si2147-A30 tuner does not require firmware loading.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Sparse is complaining about ngene's bad usage of a __user ptr:
>> drivers/media/pci/ngene/ngene-dvb.c:62:48: sparse: incorrect type in argument 2 (different address spaces)
drivers/media/pci/ngene/ngene-dvb.c:62:48: expected unsigned char const [usertype] *buf
drivers/media/pci/ngene/ngene-dvb.c:62:48: got char const [noderef] <asn:1>*buf
As this is intercepting a .write() file ops, we can't just memcpy. We need to use
copy_from_user.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by smatch:
drivers/media/dvb-core/dmxdev.c:1091 dvb_demux_poll() warn: variable dereferenced before check 'dmxdevfilter' (see line 1088)
This was introduced by changeset d102cac809.
We need to test before using it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TechnoTrend TT-connect CT2-4650 CI (0b48:3012) is an USB DVB-T2/C tuner with
the following components:
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-A20
Tuner: Silicon Labs Si2158-A20
CI chip: CIMaX SP2HF
The firmware for the tuner is the same as for TechnoTrend TT-TVStick CT2-4400.
See https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
The demodulator needs a firmware that can be extracted from the Windows drivers.
File ttConnect4650_64.sys should be extracted from
http://www.tt-downloads.de/bda-treiber_4.1.0.4.zip (MD5 sum below).
3464bfc37a47b4032568718bacba23fb ttConnect4650_64.sys
Then the firmware can be extracted:
dd if=ttConnect4650_64.sys ibs=1 skip=273376 count=6424 of=dvb-demod-si2168-a20-01.fw
The SP2 CI module requires a definition of a function cxusb_tt_ct2_4650_ci_ctrl
that is passed on to the SP2 driver and called back for CAM operations.
[crope@iki.fi: meld USB ID define patch to this]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
when usb-type tuner is pulled out, user applications did not close device's FD,
and go on polling the device, we should return POLLERR directly.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Data type of return value is unsigned int, but in function of dvb_demux_poll,
when the pointer of dmxdevfilter equals NULL, it will return -EINVAL, which
is invalid.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The needed bandwidth can be estimated using the symbol rate and
the rolloff factor. This could be useful for the frontend drivers,
as they don't need to calculate it themselves.
Reported-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While several tuners have some sort of suspend/resume
implementation, this is currently mangled with an optional
.sleep callback that it is also used to put the device on
low power mode.
Not all drivers implement it, as returning the driver from
low power may require to re-load the firmware, with takes
some time. Also, some drivers may delay it.
So, the more coherent is to add two new optional callbacks
that will let the tuners to directy implement suspend and
resume callbacks if they need.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Some fe drivers will have to do additional initialization
in their fe ops.init interfaces when called during resume.
Without the additional initialization, fe and tuner driver
resume fails. A new fe exit flag value DVB_FE_DEVICE_RESUME
is necessary to detect resume case. This patch adds a new
define and changes dvb_frontend_resume() to set it prior to
calling fe init and tuner init calls and resets it back to
DVB_FE_NO_EXIT once fe and tuner init is done.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some fe drivers attempt to access the device for power control from
their release routines. When release routines are called after device
is disconnected, the attempts fail. fe drivers should avoid accessing
the device, from their release interfaces when called from disconnect
path. dvb-frontend maintains exit flag to keep track when fe device is
disconnected in its private data structures. Export the flag in fe to
enable drivers to check the device status from their release interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added Sveon STV21 device based on Realtek RTL2832U and FC0013 tuner
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
USB ID 0b48:3014.
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-30
Tuner: Silicon Labs Si2158-20
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dvb_attach() was unbalanced, as there was no dvb_dettach. Ok,
on current cases, the dettach is done by dvbdev, but that are some
future corner cases where we may need to do this before registering
the frontend.
So, add a dvb_detach() and use it at dvb_frontend.c.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is another clone of AZ6027. This patch adds the relevant PID.
Signed-off-by: Manuel Schönlaub <manuel.schoenlaub@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Check if index is within bounds _before_ accessing the value.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If an attempt to set LNA fails, restore the cache to LNA_AUTO,
in order to make it to reflect the current LNA status.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I've got the following DAB USB stick that also works fine with the
DVB_USB_RTL28XXU driver after I added its USB ID:
Bus 001 Device 009: ID 0ccd:00b4 TerraTec Electronic GmbH
[crope@iki.fi: apply patch partly manually]
Signed-off-by: Till Dörges <till@doerges.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
This is similar to the Terratec H7. It works with the same az6007 firmware as
the former, however the drx-k firmware of the H7 will NOT work. Hence use
a different firmware name. The firmware does not need to exist as the one in
the eeprom is just fine as long as the h7 one doesn't get loaded, but maybe
some day someone wants to load it (the one from the h5 would work too).
Also since the config entry is now different anyway disable support for rc.
AFAIK the Technisat remote (TS35) is RC5 and the code (which a code comment
claims doesn't work anyway) only would handle NEC hence it's pointless creating
a device and polling it if we already know it can't work.
CI is untested.
Originally based on idea found on
http://www.linuxtv.org/wiki/index.php/TechniSat_CableStar_Combo_HD_CI claiming
only id needs to be added (but failed to mention it only worked because the
driver couldn't find the h7 drx-k firmware...).
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
removes trailing whitespace and rebalance line length in comment block
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dmx_section_feed_release_filter() locks dvbdmx->mutex and
if the feed is still filtering, it calls feed->stop_filtering(feed).
stop_filtering() is implemented by dmx_section_feed_stop_filtering()
that first of all try to lock the same mutex: dvbdmx->mutex.
That leads to a deadlock.
It does not happen often in practice because all callers of
release_filter() stop filtering by themselves.
So the problem can happen in case of race condition only.
The patch releases dvbdmx->mutex before call to feed->stop_filtering(feed)
and reacquires the mutex after that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
nobody else will see that struct file after return from ->release()
anyway; just leave ->f_op as is and let __fput() do that fops_put().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
These functions may be called inside URB->complete(), so use
spin_lock_irqsave().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In dvb_ringbuffer lock-less synchronizationof reader and writer threads is done
with separateread and write pointers. Sincedvb_ringbuffer_flush() modifies the
read pointer, this function must not be called from the writer thread.
This patch removes the dvb_ringbuffer_flush() calls in the dmxdev ringbuffer
write functions, this fixes Oopses "Unable to handle kernel paging request"
I could observe for the call chaindvb_demux_read ->dvb_dmxdev_buffer_read ->
dvb_ringbuffer_read_user -> __copy_to_user (the reader side of the ringbuffer).
The flush calls at the write side are not necessary anyway since ringbuffer_flush
is also called in dvb_dmxdev_buffer_read() when an error condition is set in the
ringbuffer.
This patch should also be applied to stable kernels.
Signed-off-by: Soeren Moch <smoch@web.de>
CC: <stable@vger.kernel.org>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
The intend of this patch is to remove the support for the dib7090E. The
DiB7090E-package has never left prototype state and never made it to
mass-prod-state.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_rf_strength op in tuner-simple is valid only for the radio mode.
But due to the way get_signal in analog_demod_ops was designed it would
overwrite the signal value with a bogus value when in TV mode.
Pass a pointer to the signal value instead, and when not in radio mode
leave it alone in the tuner-simple.
This broke in commit 030755bde4
(tuner-core: call has_signal for both TV and radio) in kernel 3.6. Before
that this was working correctly. That commit did the right thing, but what
wasn't realized at the time was that tuner-simple should have been updated
as well to restrict setting the signal strength to the radio mode only.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_afc op in tda9887 is valid only for the radio mode.
But due to the way get_afc in analog_demod_ops was designed it would
overwrite the afc value with a bogus value when in TV mode.
Pass a pointer to the afc value instead, and when not in radio mode
leave it alone in the tda9887.
This broke a long time ago in 2.6.19 when the get_afc op was introduced.
Before that the afc was only set for radio mode in the tda9887.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"enum dmx_ts_pes" and "typedef enum dmx_pes_type_t" are just the
same enum declared twice, since Kernel (2.6.12). There's no reason
to duplicate it there, and sparse complains about that:
drivers/media/dvb-core/dmxdev.c:600:55: warning: mixing different enum types
So, remove the internal define, keeping just the external one.
Internally, use only "enum dmx_ts_pes", as it is too late to drop
dmx_pes_type_t from the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids incrementing continuity counter
demux->cnt_storage[pid] for TS packets without payload in accordance
with ISO /IEC 13818-1.
[mchehab@redhat.com: unmangle whitespacing and fix CodingStyle.
Also checked ISO/IEC spec: patch is according with it]
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: John Smith <johns90812@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current logic was broken and too complex; while it works
fine for DVB-S2/DVB-S, it is broken for ISDB-T.
Make the logic simpler, fixes it for ISDB-T and make it clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is complex, and has different workflows, one for
DVBv3 calls, and another one for DVBv5 calls. Break it into 3
functions, in order to make easier to understand what each
block does.
No functional changes so far. A few comments got improved.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the AGC settings present on a newer device.
The initial settings were taken from one of the first devices with
mb86a20s, and there are several reports that this is not working
properly on some places.
So, instead of keeping using it, get the parameters taken from a
newer device. Tests are welcomed.
Tested also with cx231xx PixelView SBTVD Hybrid with no regressions
noticed so far.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
As reported by Klaus Schmidinger:
"In VDR I use an ioctl() call with FE_READ_UNCORRECTED_BLOCKS on a
device (using stb0899). After this call I check 'errno' for
EOPNOTSUPP to determine whether this device supports this call. This
used to work just fine, until a few months ago I noticed that my
devices using stb0899 didn't display their signal quality in VDR's OSD
any more. After further investigation I found that
ioctl(FE_READ_UNCORRECTED_BLOCKS) no longer returns EOPNOTSUPP, but
rather ENOTTY. And since I stop getting the signal quality in case
any unknown errno value appears, this broke my signal quality query
function."
While the changes reflect what is there at:
http://comments.gmane.org/gmane.linux.kernel/1235728
it does cause regression on userspace. So, revert it to stop the
damage.
This reverts commit 177ffe506c ("[media] dvb_frontend: return -ENOTTY
for unimplement IOCTL").
Reported-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "Technisat SkyStar USB plus" is a TT-connect S-2400 clone, which the
V4L-DVB drivers already support. However, some of these devices (like
mine) come with a different USB PID 0x3009 instead of 0x3006.
There have already been patches simply overwriting the USB PID in
dvb-usb-ids.h. Of course these patches were rejected because they would
have disabled the 0x3006 PID.
This new patch adds the 0x3009 PID to dvb-usb-ids.h, and adds references
to it within the ttusb2.c driver. PID 0x3006 devices will continue to work.
The only difference between the two hardware models seems to be the
EEPROM chip. In fact, Windows BDA driver names the 0x3009 device with a
"(8 kB EEPROM)" suffix. In spite of that, the 0x3009 device works
absolutely flawlessly using the existing ttusb2 driver.
Signed-off-by: Christoph Nuscheler <christoph.nuscheler@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If userspace calls a property that doesn't exist, it currently
just returns -EINVAL. However, this is more likely a problem at
the userspace application, calling it with a non-existing property.
So, add a debug message to help tracking it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the logic to poll, reset counters and report the QoS stats
to the end user.
The idea is that the core will periodically poll the frontend for
the stats. The frontend may return -EBUSY, if the previous collect
didn't finish, or it may fill the cached data.
The value returned to the end user is always the cached data.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We recently pushed the locking down into this function, but there was
an error path where the unlock was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since most dvb ioctls wrap their real work with dvb_usercopy, the static mutex
used in dvb_usercopy effectively is a global lock for dvb ioctls.
Unfortunately, frontend ioctls can be blocked by the frontend thread for
several seconds; this leads to unacceptable lock contention. Mitigate that by
pushing the mutex from dvb_usercopy down to the individual, device specific
ioctls.
There are 10 such ioctl functions using dvb_usercopy, either calling it
directly, or via the trivial wrapper dvb_generic_ioctl. The following already
employ their own locking and look safe:
• dvb_demux_ioctl (as per dvb_demux_do_ioctl)
• dvb_dvr_ioctl (as per dvb_dvr_do_ioctl)
• dvb_osd_ioctl (as per single non-trivial callee)
• fdtv_ca_ioctl (as per callees)
• dvb_frontend_ioctl
The following functions do not, and are thus changed to use a device specific
mutex:
• dvb_net_ioctl (as per dvb_net_do_ioctl)
• dvb_ca_en50221_io_ioctl (as per dvb_ca_en50221_io_do_ioctl)
• dvb_video_ioctl
• dvb_audio_ioctl
• dvb_ca_ioctl
Signed-off-by: Nikolaus Schulz <schulz@macnetix.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That likely fixes this MythTV ticket:
http://code.mythtv.org/trac/ticket/10830
(which btw affects all usb tuners I tested as well, pctv452e,
dib0700, af9015) pctv452e is still possibly broken with MythTV
even after this fix; it does work with VDR here tho despite I2C
errors.
Reduced testcase:
http://people.freebsd.org/~nox/tmp/ioctltst.c
Thanx to devinheitmueller and crope from #linuxtv for helping with
this fix! :)
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This just adds the usbid to the rtl28xxu driver, that's all that's
needed to make the stick work for DVB.
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for this header is to make sure that include
linux/time.h were added before uapi/*/dmx.h. Just push down the
time.h header on the few places where this is used, and drop
this new header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
* use dvb property cache
* implement get (thus API minor++)
* PCTV 290e: 1=LNA ON, all the other values LNA OFF
Also fix PCTV 290e LNA comment, it is disabled by default
Hans and Mauro proposed use of cache implementation of get as they
were planning to extend LNA usage for analog side too.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
[mchehab@redhat.com: some hunks got bitroted; applied only the
ones that succeeds]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[crope@iki.fi: For my drivers a8293, af9013, af9015, af9035]
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Demodulator cannot perform statistic IOCTLs when it is not tuned.
Return -EAGAIN in such case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unify multistream support at the DVBAPI: several delivery systems
allow it. Yet, each one had its own name. So, instead of adding
a third version of this field, remove the per-standard naming,
unifying it into a common name.
The legacy code number can still be used by old applications.
Version increased to 5.8.
[mchehab@redhat.com: joined the va1j5jf007s patch, in order to
avoid compilation breakage]
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It needs the e4000 tuner driver.
Signed-off-by: Philipp Dreimann <philipp@dreimann.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move initial suspend / resume support from dvb_usb_v2 to dvb_frontend
as it is dvb general feature that could be used all dvb devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
just like the V4L2 core, move the DVB core to drivers/media, as the
intention is to get rid of both "video" and "dvb" directories.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>