[ Upstream commit 4076a007bd ]
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the rk3328-roc-cc ethernet is enabled using "snps,force_thresh_dma_mode".
While this works, the performance leaves a lot to be desired.
A previous attempt to improve performance used "snps,txpbl = <0x4>".
This also allowed networking to function, but performance varied between boards.
This patch takes that one step further.
Set txpbl and rxpbl to 0x4.
This can also be accomplished with "snps,pbl =<0x4>" which affects both.
Also set "snps,aal" which forces address aligned DMA mode.
Fixes: 4bc4d6013b (arm64: dts: rockchip: fix rk3328-roc-cc gmac2io stability issues)
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable necessary nodes to get output on the hdmi port of the board.
This is a port of Heiko's patch for the rock64.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The eMMC 5.x that Libre Computer provide for their boards supports HS200 mode.
The support is already included in the dts for their newest board:
La Frite (AML-S805X-AC)
dts: arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
That same eMMC is supported in the ROC-RK3328-CC:
https://www.loverpi.com/products/libre-computer-board-emmc-5-x-module
This increases the speed of the eMMC significantly.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
[added supplies as suggested by Leonidas]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In line with the rock64 dts, specify the cpu-supply
for the other cpus as well
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Assign the LEDs to heartbeat and sdcard io, as in other RK boards.
f1affad5c7
Suggested-by: Juan Cano <j3cano@outlook.com>
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3328-roc-cc board exhibits tx stability issues with large packets,
as does the rock64 board, which was fixed with this patch
https://patchwork.kernel.org/patch/10178969/
A similar patch was merged for the rk3328-roc-cc here
https://patchwork.kernel.org/patch/10804863/
but it doesn't include the tx/rx_delay tweaks, and I find that they
help with an issue where large transfers would bring the ethernet
link down, causing a link reset regularly.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch is a port of the fix from
commit 73e42e1866 ("arm64: dts: rockchip: fix rock64 gmac2io stability
issues")
As per that patch, enabling thresh dma mode force disables checksuming.
This is necessary as tx checksuming does not work with packets larger
than 1498.
The rk3328-roc-cc board exhibits tx stability issues with large packets
similar to rock64's issues. This patch resolves that issue.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by the
vcc_sdio regulator, which is a mux between 1.8V and 3.3V, controlled by
a special output only gpio pin labeled "gpiomut_pmuio_iout",
corresponding bit 1 of the syscon GRF_SOC_CON10.
This special pin can now be reference as <&grf_gpio 0>, thanks to the
gpio-syscon driver, which makes writing regulator-gpio possible.
If the signal voltage changes, the io domain needs to change
correspondingly.
To use this feature, the following options are required in kernel config:
- CONFIG_GPIO_SYSCON=y
- CONFIG_POWER_AVS=y
- CONFIG_ROCKCHIP_IODOMAIN=y
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It is necessary for the io domain setting of the SoC to match the voltage
supplied by the regulators.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The roc-rk3328-cc is a credit card size single board computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 2GB 2133MHz LPDDR4 memory. It provides eMMC module socket, MicroSD
Card slot, USB 2.0/3.0, Gigabit Ethernet, HDMI/CVBS, Infrared Receiver,
SPDIF/I2S, and SPI/I2C/UART/PWM interfaces.
The devicetree currently supports basic peripherals.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Chen-Yu Tsai