The DTS is for i.MX8MP DSP offload audio playback. DSP only use OCRAM
and OCRAM_A when audio playback, so DRAM can enter retention mode to
save Power. As the size limitation of OCRAM and OCRAM_A and the size
audio decoder library, the LPA playback only can support MP3 and AAC.
OCRAM address is 0x900000-0x990000. ATF will use 0x960000-0x980000.
DSP LPA will use ocram(0x900000-0x960000) and ocram_e(0x980000-
0x990000)
Signed-off-by: Bing Song <bing.song@nxp.com>
Update the clock modes of iMX8MP PCIe PHY in binding DOC.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
commit b5265c813c upstream.
In some rare cases, for input data over 32 KB, lzo-rle could encode two
different inputs to the same compressed representation, so that
decompression is then ambiguous (i.e. data may be corrupted - although
zram is not affected because it operates over 4 KB pages).
This modifies the compressor without changing the decompressor or the
bitstream format, such that:
- there is no change to how data produced by the old compressor is
decompressed
- an old decompressor will correctly decode data from the updated
compressor
- performance and compression ratio are not affected
- we avoid introducing a new bitstream format
In testing over 12.8M real-world files totalling 903 GB, three files
were affected by this bug. I also constructed 37M semi-random 64 KB
files totalling 2.27 TB, and saw no affected files. Finally I tested
over files constructed to contain each of the ~1024 possible bad input
sequences; for all of these cases, updated lzo-rle worked correctly.
There is no significant impact to performance or compression ratio.
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Rodgman <dave.rodgman@arm.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Chao Yu <yuchao0@huawei.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200507100203.29785-1-dave.rodgman@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3798cc4d10 upstream
Make the docs match the code.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e5b3c267d upstream
SRBDS is an MDS-like speculative side channel that can leak bits from the
random number generator (RNG) across cores and threads. New microcode
serializes the processor access during the execution of RDRAND and
RDSEED. This ensures that the shared buffer is overwritten before it is
released for reuse.
While it is present on all affected CPU models, the microcode mitigation
is not needed on models that enumerate ARCH_CAPABILITIES[MDS_NO] in the
cases where TSX is not supported or has been disabled with TSX_CTRL.
The mitigation is activated by default on affected processors and it
increases latency for RDRAND and RDSEED instructions. Among other
effects this will reduce throughput from /dev/urandom.
* Enable administrator to configure the mitigation off when desired using
either mitigations=off or srbds=off.
* Export vulnerability status via sysfs
* Rename file-scoped macros to apply for non-whitelist table initializations.
[ bp: Massage,
- s/VULNBL_INTEL_STEPPING/VULNBL_INTEL_STEPPINGS/g,
- do not read arch cap MSR a second time in tsx_fused_off() - just pass it in,
- flip check in cpu_set_bug_bits() to save an indentation level,
- reflow comments.
jpoimboe: s/Mitigated/Mitigation/ in user-visible strings
tglx: Dropped the fused off magic for now
]
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "fsl,spi-only-use-cs1-sel" to fit i.MX8DXL-EVK.
Spi common code does not support use of CS signals discontinuously.
It only uses CS1 without using CS0. So, add this property to re-config
chipselect value.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
This is an adapter card made for the 4.3", 800x480, LCD panel Seiko
43WVFIG. The LCD panel is a 24bit DPI bus, while the adapter card has
two ports: 18-bit and 24-bit data input. For the 18-bit data input, the
adapter card is demuxing some of the data lines, in order to feed all of
the 24 lines needed by the LCD.
This driver handles both this use-cases.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
commit 3155f4f408 upstream.
Commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05460849c3 ]
Cores affected by Neoverse-N1 #1542419 could execute a stale instruction
when a branch is updated to point to freshly generated instructions.
To workaround this issue we need user-space to issue unnecessary
icache maintenance that we can trap. Start by hiding CTR_EL0.DIC.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fb2511247d upstream.
cmdlinepart.c has been moved to drivers/mtd/parsers/.
Fixes: a3f12a35c9 ("mtd: parsers: Move CMDLINE parser")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9f711efd4 ]
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The V2X MU requires that the the sender changes the byte indication
the type of the message in its header. The value required changes
for each MU.
This patch adds the documentation of this functionality adding
explanations for fsl,cmd_tag and fsl,rsp_tag.
Signed-off-by: Stéphane Dion <stephane.dion_1@nxp.com>
commit f36938aa74 upstream.
patch_realtek.c has historically failed to properly configure the PC
Beep Hidden Register for the ALC256 codec (among others). Depending on
your kernel version, symptoms of this misconfiguration can range from
chassis noise, picked up by a poorly-shielded PCBEEP trace, getting
amplified and played on your internal speaker and/or headphones to loud
feedback, which responds to the "Headphone Mic Boost" ALSA control,
getting played through your headphones. For details of the problem, see
the patch in this series titled "ALSA: hda/realtek - Set principled PC
Beep configuration for ALC256", which fixes the configuration.
These symptoms have been most noticed on the Dell XPS 13 9350 and 9360,
popular laptops that use the ALC256. As a result, several model-specific
fixups have been introduced to try and fix the problem, the most
egregious of which locks the "Headphone Mic Boost" control as a hack to
minimize noise from a feedback loop that shouldn't have been there in
the first place.
Now that the underlying issue has been fixed, remove all these fixups.
Remaining fixups needed by the XPS 13 are all picked up by existing pin
quirks.
This change should, for the XPS 13 9350/9360
- Significantly increase volume and audio quality on headphones
- Eliminate headphone popping on suspend/resume
- Allow "Headphone Mic Boost" to be set again, making the headphone
jack fully usable as a microphone jack too.
Fixes: 8c69729b44 ("ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3")
Fixes: 423cd78561 ("ALSA: hda - Fix headphone noise on Dell XPS 13 9360")
Fixes: e4c9fd10eb ("ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant")
Fixes: 1099f48457 ("ALSA: hda/realtek: Reduce the Headphone static noise on XPS 9350/9360")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/b649a00edfde150cf6eebbb4390e15e0c2deb39a.1585584498.git.tommyhebb@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f128090491 upstream.
This codec (among others) has a hidden set of audio routes, apparently
designed to allow PC Beep output without a mixer widget on the output
path, which are controlled by an undocumented Realtek vendor register.
The default configuration of these routes means that certain inputs
aren't accessible, necessitating driver control of the register.
However, Realtek has provided no documentation of the register, instead
opting to fix issues by providing magic numbers, most of which have been
at least somewhat erroneous. These magic numbers then get copied by
others into model-specific fixups, leading to a fragmented and buggy set
of configurations.
To get out of this situation, I've reverse engineered the register by
flipping bits and observing how the codec's behavior changes. This
commit documents my findings. It does not change any code.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/bd69dfdeaf40ff31c4b7b797c829bb320031739c.1585584498.git.tommyhebb@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DPU found in i.MX8qxp SoC may drive a parallel display through
pixel link to LCDIF mux. This patch adds the device tree binding
documentation for LCDIF mux display.
Reviewed-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Support i.MX8/8M/7ULP:
- Introduce early-booted property for M4 booted before Linux
- Introduce mboxes for rpmsg/virtio to communicate with M4
- Introduce mub-partition for hardware partition supported by i.MX8
- Introduce rsrc-table which hold the resource table
- Introduce rsrc-da
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert the i.MX remoteproc binding to DT schema format
using json-schema
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[ Upstream commit 26d5bb9e4c ]
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
For dwc3-imx8mp, the clock for its power domain hsiomix has
to be handled by user, so add the hsio root clock to dwc3 imx8mp
binding doc.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Some power domain need to be runtime always on to keep
the peripherals's weekup ability, for such power domain,
add the 'GENPD_FLAG_RPM_ALWAYS_ON' flag.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
commit 5190044c29 upstream.
In order to preserve backwards compatability with kmod tools, we have to
move the namespace field in Module.symvers last, as the depmod -e -E
option looks at the first three fields in Module.symvers to check symbol
versions (and it's expected they stay in the original order of crc,
symbol, module).
In addition, update an ancient comment above read_dump() in modpost that
suggested that the export type field in Module.symvers was optional. I
suspect that there were historical reasons behind that comment that are
no longer accurate. We have been unconditionally printing the export
type since 2.6.18 (commit bd5cbcedf4), which is over a decade ago now.
Fix up read_dump() to treat each field as non-optional. I suspect the
original read_dump() code treated the export field as optional in order
to support pre <= 2.6.18 Module.symvers (which did not have the export
type field). Note that although symbol namespaces are optional, the
field will not be omitted from Module.symvers if a symbol does not have
a namespace. In this case, the field will simply be empty and the next
delimiter or end of line will follow.
Cc: stable@vger.kernel.org
Fixes: cb9b55d21f ("modpost: add support for symbol namespaces")
Tested-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f9e12e0df ]
In case the WDAT interface is broken, give the user an option to
ignore it to let a native driver bind to the watchdog device instead.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The phy registers are accessible after APB clock is enabled.
So, add the relevant clock properties in device tree doc.
Reviewed-by: Sandor Yu <Sandor.yu@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
commit d9a9f4849f upstream.
several iterations of ->atomic_open() calling conventions ago, we
used to need fput() if ->atomic_open() failed at some point after
successful finish_open(). Now (since 2016) it's not needed -
struct file carries enough state to make fput() work regardless
of the point in struct file lifecycle and discarding it on
failure exits in open() got unified. Unfortunately, I'd missed
the fact that we had an instance of ->atomic_open() (cifs one)
that used to need that fput(), as well as the stale comment in
finish_open() demanding such late failure handling. Trivially
fixed...
Fixes: fe9ec8291f "do_last(): take fput() on error after opening to out:"
Cc: stable@kernel.org # v4.7+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the active wakeup flag if a power domain has such requirement.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
i.MX8/8X SECO MU is dedicated for communication between kernel
and SECO. To use SECO MU more effectivly, add "fsl,imx8-seco-mu"
compatible to support fast IPC.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
commit 78e06cf430 upstream.
In the flowtable documentation there is a missing semicolon, the command
as is would give this error:
nftables.conf:5:27-33: Error: syntax error, unexpected devices, expecting newline or semicolon
hook ingress priority 0 devices = { br0, pppoe-data };
^^^^^^^
nftables.conf:4:12-13: Error: invalid hook (null)
flowtable ft {
^^
Fixes: 19b351f16f ("netfilter: add flowtable documentation")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcbb8461fd upstream.
There are both positive and negative options about this feature.
At first, I thought it was a good idea, but actually Linus stated a
negative opinion (https://lkml.org/lkml/2019/9/29/227). I admit it
is ugly and annoying.
The baseline I'd like to keep is the compile-test of uapi headers.
(Otherwise, kernel developers have no way to ensure the correctness
of the exported headers.)
I will maintain a small build rule in usr/include/Makefile.
Remove the other header test functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ added to 5.4.y due to start of build warnings from backported patches
because of this feature - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver support for i.MX8DXL DB Perf, which supports AXI ID PORT
CHANNEL filter.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Add driver support for i.MX8DXL DDR Perf, which supports AXI ID PORT
CHANNEL filter.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
commit dcde237319 upstream.
Currently the arm64 kernel ignores the top address byte passed to brk(),
mmap() and mremap(). When the user is not aware of the 56-bit address
limit or relies on the kernel to return an error, untagging such
pointers has the potential to create address aliases in user-space.
Passing a tagged address to munmap(), madvise() is permitted since the
tagged pointer is expected to be inside an existing mapping.
The current behaviour breaks the existing glibc malloc() implementation
which relies on brk() with an address beyond 56-bit to be rejected by
the kernel.
Remove untagging in the above functions by partially reverting commit
ce18d171cb ("mm: untag user pointers in mmap/munmap/mremap/brk"). In
addition, update the arm64 tagged-address-abi.rst document accordingly.
Link: https://bugzilla.redhat.com/1797052
Fixes: ce18d171cb ("mm: untag user pointers in mmap/munmap/mremap/brk")
Cc: <stable@vger.kernel.org> # 5.4.x-
Cc: Florian Weimer <fweimer@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Victor Stinner <vstinner@redhat.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for a new clock 'phy_parent'. This clock is optional
and is used to re-parent the PHY related clocks (phy_ref, tx_esc and
rx_esc) to a valid parent. This clock is needed, in order to make the
re-parenting in driver, since the default re-parenting in dts node
(using assigned-clock-parents) may break the LVDS block, which has it's
PHY shared with MIPI-DSI.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
(cherry picked from commit 7ed3b8738e3103396a5f3a9268c66f11f78cab03)
Some MAC PCS blocks are unable to provide interrupts when their status
changes. As we already have support in phylink for polling status, use
this to provide a hook for MACs to enable polling mode.
The patch idea was picked up from Russell King's suggestion on the macb
phylink patch thread here [0] but the implementation was changed.
Instead of introducing a new phylink_start_poll() function, which would
make the implementation cumbersome for common PHYLINK implementations
for multiple types of devices, like DSA, just add a boolean property to
the phylink_config structure, which is just as backwards-compatible.
https://lkml.org/lkml/2019/12/16/603
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Conflicts:
drivers/net/phy/phylink.c
with upstream commit 24cf0e693b ("net: phylink: split link_an_mode
configured and current settings") submitted for net-next and merged
during v5.5-rc1.
(cherry picked from commit ac7420c5ede06ebe049c6bce8ba9e9d7d3a51d11)
QORIQ LS1028A soc used fsl,vf610-edma, but it has a little bit different
from others, so add new compatible to distinguish them.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20191212033714.4090-3-peng.ma@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
(cherry picked from commit f8dd1f395d1fbba049900ed48c09d76df49be712)
[ Upstream commit fd933c00eb ]
Three shall be the number thou shalt count, and the number of the
counting shall be three. Four shalt thou not count...
One! Two! Five!
Fixes: efb985f6b2 ("[PATCH] fbcon: Console Rotation - Add framebuffer console documentation")
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827110854.12574-2-peda@axentia.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add "mem" clock that is required for imx8dxl platform.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Add information for i.MX8MP DDRC which reports the single bit errors
that are corrected and the double bit errors that are detected.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Add two parameters which are used to tune USB signal for imx picophy,
picophy is used at imx7d and imx8mm.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
commit a6c4f77cb3 upstream.
This patch set the correct value for oversampling maxItems. In the
original example, appears 3 items for oversampling while the maxItems
is set to 1, this patch fixes those issues.
Fixes: 416f882c3b ("dt-bindings: iio: adc: Migrate AD7606 documentation to yaml")
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bing Song