This adds the URAM block on SH7722 as a separate node.
Sparsemem is required for this, or it can simply be disabled
by explicitly selecting a flatmem model.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic support for multiple nodes on SH machines.
This is primarily useful for boards with many different
memory blocks that are otherwise unused (SH7722/SH7785 URAM
and so forth).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements basic sparsemem support for SH. Presently this only
uses static sparsemem, and we still permit explicit selection of
flatmem. Those boards that want sparsemem can select it as usual.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that select no longer works for selecting the "closest" CPU,
we have to explicitly reference the precise sub-type in the few
places where it actually matters (presently only setup code and
some legacy sh-sci cruft).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was a big mess, rework the logic a bit so that we constrain
to a particular subtype and figure out the board support based
on that. This makes building subtype specific kernels supporting
multiple boards possible again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Most SH platforms aren't going to need more than a single active
region, ones that need more can pad this out as necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves SH over to the generic quicklists. As per x86_64,
we have special mappings for the PGDs, so these go on their
own list..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks some of the node 0 bootmem initialization in
preparation for discontigmem and sparsemem support.
ARCH_POPULATES_NODE_MAP is switched to as a result of this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the lazy dcache handling to the model described in
Documentation/cachetlb.txt and drops the ptep_get_and_clear() hacks
used for the aliasing dcaches on SH-4 and SH7705 in 32kB mode. As a
bonus, this slightly cuts down on the cache flushing frequency.
With that and the PTEA handling out of the way, the update_mmu_cache()
implementations can be consolidated, and we no longer have to worry
about which configuration the cache is in for the SH7705 case.
And finally, explicitly disable the lazy writeback on SMP (SH-4A).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up shmin (and SH7706/SH7708) IPR support for some of the
recent API changes.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle simple TLB miss faults which can be resolved completely
from the page table in assembler.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some preliminary support for the SH-X2 MMU, used by
newer SH-4A parts (particularly SH7785).
This MMU implements a 'compat' mode with SH-X MMUs and an
'extended' mode for SH-X2 extended features. Extended features
include additional page sizes (8kB, 4MB, 64MB), as well as the
addition of page execute permissions.
The extended mode attributes are placed in a second data array,
which requires us to switch to 64-bit PTEs when in X2 mode.
With the addition of the exec perms, we also overhaul the mmap
prots somewhat, now that it's possible to handle them more
intelligently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the vsyscall page on SH.
At the moment we leave it configurable due to having nommu
to support from the same code base. We hook it up for the
signal trampoline return at present, with more to be added
later, once uClibc catches up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the aforementioned CPU subtypes, and cleans
up some build issues encountered as a result.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
nommu needs to be able to shift PAGE_OFFSET, so we switch it to a
non-user-visible CONFIG_PAGE_OFFSET and use that in the few places
where it matters.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently the CPU subtype options are cluttering up arch/sh/Kconfig somewhat.
Given that, this moves all of that in to its own arch/sh/mm/Kconfig. Things
like cache configuration are also moved to this new location.
This also adds support for strict CPU tuning on newer cores, which requires
the addition of as-option.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mundt