fix for error that is introduced by
| x86: Use find_e820() instead of hard coded trampoline address
it should end with PAGE_SIZE + PAGE_SIZE
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-2-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Due to recent changes wakeup and mptable, we run out of early
reservations on 32-bit NUMA. Thus, adjust the available number.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B22D754.2020706@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jens found the following crash/regression:
[ 0.000000] found SMP MP-table at [ffff8800000fdd80] fdd80
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 0-fff BIOS data page
and
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 6000-7fff TRAMPOLINE
and bisected it to b24c2a9 ("x86: Move find_smp_config()
earlier and avoid bootmem usage").
It turns out the BIOS is using the first 64k for mptable,
without reserving it.
So try to find good range for the real-mode trampoline instead of
hard coding it, in case some bios tries to use that range for sth.
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4B21630A.6000308@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=13940
on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them. It then apparently hits some undocumented resource conflict,
resulting in non-working devices.
Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since alloc_bootmem() will never return inaccessible (via virtual
addressing) memory anyway, using the ..._low() variant only makes sense
when the physical address range of the allocated memory must fulfill
further constraints, espacially since on 64-bits (or more generally in all
cases where the pools the two variants allocate from are than the full
available range.
Probably the use in alloc_tce_table() could also be eliminated (based on
code inspection of pci-calgary_64.c), but that seems too risky given I
know nothing about that hardware and have no way to test it.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
memory_setup is overridden by x86_quirks and by paravirts with weak
functions and quirks. Unify the whole mess and make it an
unconditional x86_init_ops function which defaults to the standard
function and can be overridden by the early platform code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix hang with HIGHMEM_64G and 32bit resource. According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.
Analyzed by hpa
Reported-and-tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the e820 code explicitly reserves 'potentially dangerous'
free physical memory address space to protect ACPI stolen RAM,
there's no need for the rounding quirk in the PCI allocator anymore.
Also, this quirk was open-ended iteration that could end up reserving
a lot of free space and potentially breaking drivers - such as the one
reported by Yannick Roehlly <yannick.roehlly@free.fr> where there's
a PCI device with a large memory resource.
So remove it.
[ Impact: make more of the PCI hole available for assigning pci devices ]
Reported-by: Yannick Roehlly <yannick.roehlly@free.fr>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01A7C8.5090701@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The point is to take all RAM resources we have, and
_after_ we've added all the resources we've seen in
the E820 tree, we then _also_ try to add fake reserved
entries for any "round up to X" at the end of the RAM
resources.
[ Impact: improve PCI mem-resource allocation robustness, protect "stolen RAM" ]
Reported-by: Yannick Roehlly <yannick.roehlly@free.fr>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: yannick.roehlly@free.fr
LKML-Reference: <4A01A784.2050407@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the first non-reserved (sub-)range doesn't fit the size requested,
an endless loop will be entered. If a range returned from
find_e820_area_size() turns out insufficient in size, the range must
be skipped before calling the function again.
[ Impact: fixes boot hang on some platforms ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
This fixed various signedness issues in setup.c and e820.c:
arch/x86/kernel/setup.c:455:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:455:53: expected int *pnr_map
arch/x86/kernel/setup.c:455:53: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:639:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:639:53: expected int *pnr_map
arch/x86/kernel/setup.c:639:53: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/setup.c:820:54: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/setup.c:820:54: expected int *pnr_map
arch/x86/kernel/setup.c:820:54: got unsigned int extern [toplevel] *<noident>
arch/x86/kernel/e820.c:670:53: warning: incorrect type in argument 3 (different signedness)
arch/x86/kernel/e820.c:670:53: expected int *pnr_map
arch/x86/kernel/e820.c:670:53: got unsigned int [toplevel] *<noident>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Impact: help debug e820 bugs
Try to print out more info, to catch wrong call parameters.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BCB557.3030000@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: enhance e820 code to handle more cases
Try to handle new range which could be covered by one entry.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: jbeulich@novell.com
LKML-Reference: <49B9F0C1.10402@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix left range size on head
| commit 5c0e6f035d
| x86: fix code paths used by update_mptable
| Impact: fix crashes under Xen due to unrobust e820 code
fixes one e820 bug, but introduces another bug.
Need to update size for left range at first in case it is header.
also add __e820_add_region take more parameter.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: jbeulich@novell.com
LKML-Reference: <49B9E286.502@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix crashes under Xen due to unrobust e820 code
find_e820_area_size() must return a properly distinguishable and
out-of-bounds value when it fails, and -1UL does not meet that
criteria on i386/PAE. Additionally, callers of the function must
check against that value.
early_reserve_e820() should be prepared for the region found to be
outside of the addressable range on 32-bits.
e820_update_range_map() should not blindly update e820, but should do
all it work on the map it got a pointer passed for (which in 50% of the
cases is &e820_saved). It must also not call e820_add_region(), as that
again acts on e820 unconditionally.
The issues were found when trying to make this option work in our Xen
kernel (i.e. where some of the silent assumptions made in the code
would not hold).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49B9171B.76E4.0078.0@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce new initcall for marking the ACPI NVS memory at startup, so
that it can be saved/restored during hibernation/resume.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: fix trampoline sizing bug, save space
While debugging a suspend-to-RAM related issue it occured to me that
if the trampoline code had grown past 4 KB, we would have been
allocating too little memory for it, since the 4 KB size of the
trampoline is hardcoded into arch/x86/kernel/e820.c . Change that
by making the kernel compute the trampoline size and allocate as much
memory as necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.
This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions. It also
makes for a simpler and more accurate resource tree.
Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.
With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:
e0000000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
where only the pre-allocated special regions (IOAPIC and HPET) were kept
around.
With 2.6.28-rc2, which uses 'reserve_region_with_split()', Jonathan's
resource tree looked like this:
e0000000-fe7fffff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe800000-fe8fffff : reserved
fe900000-fe9d9aff : reserved
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9b00-fe9d9bff : reserved
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : reserved
fe9da000-fe9dafff : 0000:00:03.3
fe9da000-fe9dafff : reserved
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : reserved
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : reserved
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : reserved
fea00000-fea7ffff : 0000:00:02.0
fea00000-fea7ffff : reserved
fea80000-feafffff : 0000:00:02.1
fea80000-feafffff : reserved
feb00000-febfffff : 0000:00:02.0
feb00000-febfffff : reserved
fec00000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:
e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]
with this patch, the resource tree instead becomes
e0000000-fed003ff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : ehci_hcd
fe9da000-fe9dafff : 0000:00:03.3
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : e1000e
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : ICH HD audio
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : e1000e
fea00000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.1
feb00000-febfffff : 0000:00:02.0
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: Jonathan Corbet <corbet@lwn.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no good reason why a resource_size_t shouldn't just be a
physical address, so simply redefine it in terms of phys_addr_t.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
try to insert_resource second time, by expanding the resource...
for case: e820 reserved entry is partially overlapped with bar res...
hope it will never happen
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this one replaces:
| commit a2bd7274b4
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Mon Aug 25 00:56:08 2008 -0700
|
| x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
v2: insert e820 reserve resources before pnp_system_init
v3: fix merging problem in tip/x86/core
v4: address Linus's review about comments and condition in _late()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could let BAR res register at first, or even pnp.
v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for the E820_UNUSABLE memory type, which is defined in
Revision 3.0b (Oct. 10, 2006) of the ACPI Specification on p. 394 Table
14-1:
AddressRangeUnusuable This range of address contains memory in which
errors have been detected. This range must not be used by the OSPM.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce x86_quirks array of boot-time quirk methods.
No change in functionality intended.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
end_user_pfn used to modify the meaning of the e820 maps.
Now that all e820 operations are cleaned up, unified, tightened up,
the e820 map always get updated to reality, we don't need to keep
this secondary mechanism anymore.
If you hit this commit in bisection it means something slipped through.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also let mem= to print out modified e820 map too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add early quirks support.
In preparation of enabling the generic architecture to boot on a VISWS.
This will allow us to remove the VISWS subarch and all its complications.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
even on 64bit systems with less than 4G RAM, we can now use fixmap
to handle acpi SIT near end of ram.
change e820_end to e820_end_of_ram again?
or e820_ram_pfn?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
to avoid warning from find_low_pfn_range for high pages size etc
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When system have 4g less ram installed, and acpi table sit
near end of ram, make max_pfn cover them too,
so 64bit kernel don't need to mess up fixmap.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "Suresh Siddha" <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so when it is called after early_param, e820_saved get updated too.
esp for mpc update.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so other path that will override memory_setup or
machine_specific_memory_setup could have e820_saved too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch uses the /sys/firmware/memmap interface provided in the last patch
on the x86 architecture when E820 is used. The patch copies the E820
memory map very early, and registers the E820 map afterwards via
firmware_map_add_early().
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so it has a more meaningful name.
also change it to static.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
e820_search_gap also take a end_addr parameter to limit search from
start_addr to end_addr.
Signed-off-by: AloK N Kataria <akataria@vmware.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "lenb@kernel.org" <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
