Compared to the other supported chips, the m41t62 uses a different
register to set the square wave frequency.
Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The v3020 RTC can be connected to GPIOs as well as to memory-like
interface. Add ability to use GPIO bit-bang for v3020 read-write access.
[akpm@linux-foundation.org: fix off-by-one in error path]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
initramfs uses printk without a linefeed, then does some work, then uses
printk to finish the message off. However if some other code does a
printk in between, then the messages get mixed together. Better for each
message to be an independent line...
Example of problem that this fixes:
checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
it is
Signed-off-by: Simon Kitching <skitching@apache.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Define new setup() hook to export the accessor
- Implement accessor methods
Moves some error checking out of the sysfs interface code into the layer
below it, which is now shared by both sysfs and memory access code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the case of at24, the platform code registers a 'setup' callback with
the at24_platform_data. When the at24 driver detects an EEPROM, it fills
out the read and write functions of the memory_accessor and calls the
setup callback passing the memory_accessor struct. The platform code can
then use the read/write functions in the memory_accessor struct for
reading and writing the EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an interface by which other kernel code can read/write persistent
memory such as I2C or SPI EEPROMs, or devices which provide NVRAM. Use
cases include storage of board-specific configuration data like Ethernet
addresses and sensor calibrations.
Original idea, review and improvement suggestions by David Brownell.
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warnings:
arch/um/kernel/syscall.c: In function 'kernel_execve':
arch/um/kernel/syscall.c:130: warning: passing argument 1 of 'um_execve' discards qualifiers from pointer target type
arch/um/kernel/syscall.c:130: warning: passing argument 2 of 'um_execve' discards qualifiers from pointer target type
arch/um/kernel/syscall.c:130: warning: passing argument 3 of 'um_execve' discards qualifiers from pointer target type
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following link error:
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x11c): undefined reference to `ptregs_fork'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x140): undefined reference to `ptregs_execve'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x2cc): undefined reference to `ptregs_iopl'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x2d8): undefined reference to `ptregs_vm86old'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x2f0): undefined reference to `ptregs_sigreturn'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x2f4): undefined reference to `ptregs_clone'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x3ac): undefined reference to `ptregs_vm86'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x3c8): undefined reference to `ptregs_rt_sigreturn'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x3fc): undefined reference to `ptregs_sigaltstack'
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x40c): undefined reference to `ptregs_vfork'
This was introduced by commit 253f29a4, "x86: pass in pt_regs pointer
for syscalls that need it"
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following compile error:
arch/um/drivers/net_kern.c: In function 'uml_inetaddr_event':
arch/um/drivers/net_kern.c:760: error: 'struct net_device' has no member named 'open'
This was introduced by commit 8bb95b39, "uml: convert network device
to netdevice ops".
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The missing device table means that the floppy module is not auto-loaded,
even when the appropriate PNP device (0700) is found.
We don't actually use the table in the module, since the device doesn't
have a struct pnp_driver, but it's sufficient to cause an alias in the
module that udev/modprobe will use.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Philippe De Muyter <phdm@macqel.be>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check bh->b_blocknr only if BH_Mapped is set.
akpm: I doubt if b_blocknr is ever uninitialised here, but it could
conceivably cause a problem if we're doing a lookup for block zero.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A new "address_space flag"--AS_MM_ALL_LOCKS--was defined to use the next
available AS flag while the Unevictable LRU was under development. The
Unevictable LRU was using the same flag and "no one" noticed. Current
mainline, since 2.6.28, has same value for two symbolic flag names.
So, define a unique flag value for AS_UNEVICTABLE--up close to the other
flags, [at the cost of an additional #ifdef] so we'll notice next time.
Note that #ifdef is not actually required, if we don't mind having the
unused flag value defined.
Replace #defines with an enum.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include fiemap.h in header-y; it defines the interface for the
FS_IOC_FIEMAP file mapping ioctl.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The calculation of the value nr in do_xip_mapping_read is incorrect. If
the copy required more than one iteration in the do while loop the copies
variable will be non-zero. The maximum length that may be passed to the
call to copy_to_user(buf+copied, xip_mem+offset, nr) is len-copied but the
check only compares against (nr > len).
This bug is the cause for the heap corruption Carsten has been chasing
for so long:
*** glibc detected *** /bin/bash: free(): invalid next size (normal): 0x00000000800e39f0 ***
======= Backtrace: =========
/lib64/libc.so.6[0x200000b9b44]
/lib64/libc.so.6(cfree+0x8e)[0x200000bdade]
/bin/bash(free_buffered_stream+0x32)[0x80050e4e]
/bin/bash(close_buffered_stream+0x1c)[0x80050ea4]
/bin/bash(unset_bash_input+0x2a)[0x8001c366]
/bin/bash(make_child+0x1d4)[0x8004115c]
/bin/bash[0x8002fc3c]
/bin/bash(execute_command_internal+0x656)[0x8003048e]
/bin/bash(execute_command+0x5e)[0x80031e1e]
/bin/bash(execute_command_internal+0x79a)[0x800305d2]
/bin/bash(execute_command+0x5e)[0x80031e1e]
/bin/bash(reader_loop+0x270)[0x8001efe0]
/bin/bash(main+0x1328)[0x8001e960]
/lib64/libc.so.6(__libc_start_main+0x100)[0x200000592a8]
/bin/bash(clearerr+0x5e)[0x8001c092]
With this bug fix the commit 0e4a9b5928
"ext2/xip: refuse to change xip flag during remount with busy inodes" can
be removed again.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align rekey_work. Even though it's infrequent, we may as well line it up.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though vmstat_work is marked deferrable, there are still benefits to
aligning it. For certain applications we want to keep OS jitter as low as
possible and aligning timers and work so they occur together can reduce
their overall impact.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dirtied_when value on an inode is supposed to represent the first time
that an inode has one of its pages dirtied. This value is in units of
jiffies. It's used in several places in the writeback code to determine
when to write out an inode.
The problem is that these checks assume that dirtied_when is updated
periodically. If an inode is continuously being used for I/O it can be
persistently marked as dirty and will continue to age. Once the time
compared to is greater than or equal to half the maximum of the jiffies
type, the logic of the time_*() macros inverts and the opposite of what is
needed is returned. On 32-bit architectures that's just under 25 days
(assuming HZ == 1000).
As the least-recently dirtied inode, it'll end up being the first one that
pdflush will try to write out. sync_sb_inodes does this check:
/* Was this inode dirtied after sync_sb_inodes was called? */
if (time_after(inode->dirtied_when, start))
break;
...but now dirtied_when appears to be in the future. sync_sb_inodes bails
out without attempting to write any dirty inodes. When this occurs,
pdflush will stop writing out inodes for this superblock. Nothing can
unwedge it until jiffies moves out of the problematic window.
This patch fixes this problem by changing the checks against dirtied_when
to also check whether it appears to be in the future. If it does, then we
consider the value to be far in the past.
This should shrink the problematic window of time to such a small period
(30s) as not to matter.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Ian Kent <raven@themaw.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
filp->f_flags is unsigned, so use that type for the local copy.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clear_inode() will switch inode state from I_FREEING to I_CLEAR, and do so
_outside_ of inode_lock. So any I_FREEING testing is incomplete without a
coupled testing of I_CLEAR.
So add I_CLEAR tests to drop_pagecache_sb(), generic_sync_sb_inodes() and
add_dquot_ref().
Masayoshi MIZUMA discovered the bug in drop_pagecache_sb() and Jan Kara
reminds fixing the other two cases.
Masayoshi MIZUMA has a nice panic flow:
=====================================================================
[process A] | [process B]
| |
| prune_icache() | drop_pagecache()
| spin_lock(&inode_lock) | drop_pagecache_sb()
| inode->i_state |= I_FREEING; | |
| spin_unlock(&inode_lock) | V
| | | spin_lock(&inode_lock)
| V | |
| dispose_list() | |
| list_del() | |
| clear_inode() | |
| inode->i_state = I_CLEAR | |
| | | V
| | | if (inode->i_state & (I_FREEING|I_WILL_FREE))
| | | continue; <==== NOT MATCH
| | |
| | | (DANGER from here on! Accessing disposing inode!)
| | |
| | | __iget()
| | | list_move() <===== PANIC on poisoned list !!
V V |
(time)
=====================================================================
Reported-by: Masayoshi MIZUMA <m.mizuma@jp.fujitsu.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a number of issues with the per-MM VMA patch:
(1) Make mmap_pages_allocated an atomic_long_t, just in case this is used on
a NOMMU system with more than 2G pages. Makes no difference on a 32-bit
system.
(2) Report vma->vm_pgoff * PAGE_SIZE as a 64-bit value, not a 32-bit value,
lest it overflow.
(3) Move the allocation of the vm_area_struct slab back for fork.c.
(4) Use KMEM_CACHE() for both vm_area_struct and vm_region slabs.
(5) Use BUG_ON() rather than if () BUG().
(6) Make the default validate_nommu_regions() a static inline rather than a
#define.
(7) Make free_page_series()'s objection to pages with a refcount != 1 more
informative.
(8) Adjust the __put_nommu_region() banner comment to indicate that the
semaphore must be held for writing.
(9) Limit the number of warnings about munmaps of non-mmapped regions.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build failure with generic debug pagealloc:
mm/debug-pagealloc.c: In function 'set_page_poison':
mm/debug-pagealloc.c:8: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'clear_page_poison':
mm/debug-pagealloc.c:13: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'page_poison':
mm/debug-pagealloc.c:18: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: At top level:
mm/debug-pagealloc.c:120: error: redefinition of 'kernel_map_pages'
include/linux/mm.h:1278: error: previous definition of 'kernel_map_pages' was here
mm/debug-pagealloc.c: In function 'kernel_map_pages':
mm/debug-pagealloc.c:122: error: 'debug_pagealloc_enabled' undeclared (first use in this function)
by fixing
- debug_flags should be in struct page
- define DEBUG_PAGEALLOC config option for all architectures
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy/paste error. The RV670 microcode should work ok, so it's
not a show stopper.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove unused #include <version.h> in drivers/net/qlge/qlge_ethtool.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused #include <version.h> in drivers/net/dnet.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that trivial reset of pcount to one was not sufficient
in tcp_retransmit_skb. Multiple counters experience a positive
miscount when skb's pcount gets lowered without the necessary
adjustments (depending on skb's sacked bits which exactly), at
worst a packets_out miscount can crash at RTO if the write queue
is empty!
Triggering this requires mss change, so bidir tcp or mtu probe or
like.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need full-scale adjustment to fix a TCP miscount in the next
patch, so just move it into a helper and call for that from the
other places.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices cannot send very short usb transfers. To get around this the
firmware adds a known pattern and flags the driver that it should check for
this pattern on short transfers. This flag was not taken into account by
the driver.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the order in which things are freed. This fixes an oops when
unplugging the device while network traffic is ongoing.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EDIDs should be backward compatible, so don't bail if we see a version
of 3 (which is out there now) and print a message if we see something
newer, but allow it to be parsed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether the INTERLACE/DBLSCAN is supported by output device. If
not, the mode containing the flag of INTERLACE/DBLSCAN will be marked
as unsupported.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Should be,
edid_vendor[2] = (edid->mfg_id[1] & 0x1f) + '@';
Since vendor ID has only two bytes only, I am somewhat surprised why gcc
doesn't complain this.
Reported-by: Guo, Chaohong <chaohong.guo@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an include that isn't actually needed to prevent needless
rebuilds.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The readq/writeq really need to be static inline on the arches which
don't provide them.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, the PAGE_CACHE_WC would end up getting us a UC-only mapping, and
the write performance of GTT maps dropped 10x.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: cleaned up unused var]
Signed-off-by: Eric Anholt <eric@anholt.net>
Add EXPORT_SYMBOL_GPL(fsl_pq_mdio_bus_name) for module builds
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1577ecef76 ("netdev: Merge UCC
and gianfar MDIO bus drivers") introduced a regression so that UCC
MDIO buses no longer work.
This is because fsl_pq_mdio driver wrongly masks all non-TBI PHYs
for !fsl,gianfar-mdio buses, while it should do that only for
fsl,gianfar-tbi buses.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver should pass a device that actually specifies internal DMA
ops, but currently it passes netdev's device, which is wrong and that
causes following oops:
Kernel BUG at c01c4df8 [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c01c4df8] get_new_skb+0x7c/0xf8
LR [c01c4da4] get_new_skb+0x28/0xf8
Call Trace:
[ef82be00] [c01c4da4] get_new_skb+0x28/0xf8 (unreliable)
[ef82be20] [c01c4eb8] rx_bd_buffer_set+0x44/0x98
[ef82be40] [c01c62bc] ucc_geth_startup+0x11b0/0x147c
[ef82be80] [c01c6674] ucc_geth_open+0xec/0x2a4
[ef82bea0] [c02288a4] dev_open+0xc0/0x11c
[...]
Fix this by passing of_device's device that specifies DMA ops in its
archdata.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix to get cs89x0 network driver working on i.MX31ADS
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver contains experimental NAPI code disabled by default.
The commit bea3348ee ("[NET]: Make NAPI polling independent of struct
net_device objects.") converted the NAPI path of this driver but that
conversion was not complete. This patch fixes a build error
introduced by the commit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Vendor/Product ID's for new devices.
Removed duplicate product ID 0x7361.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver is exclusively an of_platform driver we no longer
use the structs and #defines in fsl_devices.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver is exclusively an of_platform driver we no longer
use the structs and #defines in fsl_devices.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO assumes that there is a one-to-one relationship between NAPI
structure and network device. Some devices like sky2 share multiple
devices on a single interrupt so only have one NAPI handler. Rather than
split GRO from NAPI, just have GRO assume if device changes that
it is a different flow.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
