The TFP410 supports 24 bit, single-edge and 12 bit, dual-edge modes.
Depending on how many wires are used (24/12) the driver can set the correct
bus_format.
If the information is not available in DT then assume 24 bit, single-edge
setup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401124143.17179-3-peter.ujfalusi@ti.com
In case either the HPD gpio is not specified or when the HPD gpio can not
be used as interrupt we should tell the core that the HPD needs to be
polled for detecting hotplug.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401123342.15767-1-peter.ujfalusi@ti.com
The TFP410 supports configurable pixel clock sampling edge and data
de-skew adjustments. The configuration can be set through I2C or
dedicated chip pins.
Report the configuration through the drm_bridge timings. As the
ti-tftp410 driver doesn't support configuring the chip through I2C, we
simply use the default configuration in that case. When the chip is
configured through dedicated pins, we parse the configuration from DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TFP410 has a powerdown pin that can be connected to a GPIO to
control power saving. The DT bindings define a corresponding property,
but the driver doesn't implement support for it. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TI TFP410 is a DVI encoder, not a full HDMI encoder. Its output can
be routed to a DVI-D connector, even if in many cases embedded systems
will use an HDMI connector to carry the DVI signals.
Instead of hardcoding the connector type to HDMI, retrieve the connector
type from its DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM bus flags convey additional information on pixel data on
the bus. All current available bus flags might be of interest for
a bridge. Remove the sampling_edge field and use bus_flags.
In the case at hand a dumb VGA bridge needs a specific data enable
polarity (DRM_BUS_FLAG_DE_LOW).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM_BUS_FLAG_PIXDATA_(POS|NEG)EDGE and
DRM_BUS_FLAG_SYNC_(POS|NEG)EDGE flags are deprecated in favour of the
new DRM_BUS_FLAG_PIXDATA_(DRIVE|SAMPLE)_(POS|NEG)EDGE and
new DRM_BUS_FLAG_SYNC_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags. Replace them
through the code.
This effectively changes the value of the .sampling_edge bridge timings
field in the dumb-vga-dac driver. This is safe to do as no driver
consumes these values yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----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=GlRQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for the 5.1 merge window.
The big changes I'd highlight are:
- nouveau has HMM support now, there is finally an in-tree user so we
can quieten down the rip it out people.
- i915 now enables fastboot by default on Skylake+
- Displayport Multistream support has been refactored and should
hopefully be more reliable.
Core:
- header cleanups aiming towards removing drmP.h
- dma-buf fence seqnos to 64-bits
- common helper for DP mst hotplug for radeon,i915,amdgpu + new
refcounting scheme
- MST i2c improvements
- drm_syncobj_cb removal
- ARM FB compression fourcc
- P010 + P016 fourcc
- allwinner tiled format modifier
- i2c over aux I2C_M_STOP support
- DRM_AUTH handling fixes
TTM:
- ref/unref renaming
New driver:
- ARM komeda display driver
scheduler:
- refactor mirror list handling
- rework hw fence processing
- 0 run queue entity fix
bridge:
- TI DS90C185 LVDS bridge
- thc631lvdm83d bridge improvements
- cadence + allwinner DSI ported to generic phy
panels:
- Sitronix ST7701 panel
- Kingdisplay KD097D04
- LeMaker BL035-RGB-002
- PDA 91-00156-A0
- Innolux EE101IA-01D
i915:
- Enable fastboot by default on SKL+/VLV/CHV
- Export RPCS configuration for ICL media driver
- Coffelake PCI ID
- CNL clocks setup fixes
- ACPI/PMIC support for MIPI/DSI
- Per-engine WA init for all engines
- Shrinker locking fixes
- Kerneldoc updates
- Lots of ring improvements and reset fixes
- Coffeelake GVT Support
- VFIO GVT EDID Region support
- runtime PM wakeref tracking
- ILK->IVB primary plane enable delays
- userptr mutex locking fixes
- DSI fixes
- LVDS/TV cleanups
- HW readout fixes
- LUT robustness fixes
- ICL display and watermark fixes
- gem mmap race fix
amdgpu:
- add scheduled dependencies interface
- DCC on scanout surfaces
- vega10/20 BACO support
- Multiple IH rings on soc15
- XGMI locking fixes
- DC i2c/aux cleanups
- runtime SMU debug interface
- Kexec improvmeents
- SR-IOV fixes
- DC freesync + ABM fixes
- GDS fixes
- GPUVM fixes
- vega20 PCIE DPM switching fixes
- Context priority handling fixes
radeon:
- fix missing break in evergreen parser
nouveau:
- SVM support via HMM
msm:
- QCOM Compressed modifier support
exynos:
- s5pv210 rotator support
imx:
- zpos property support
- pending update fixes
v3d:
- cache flush improvments
vc4:
- reflection support
- HDMI overscan support
tegra:
- CEC refactoring
- HDMI audio fixes
- Tegra186 prep work
- SOR crossbar device tree fixes
sun4i:
- implicit fencing support
- YUV and scalar support improvements
- A23 support
- tiling fixes
atmel-hlcdc:
- clipping and rotation property fixes
qxl:
- BO and PRIME improvements
- generic fbdev emulation
dw-hdmi:
- HDMI 2.0 2160p
- YUV420 ouput
rockchip:
- implicit fencing support
- reflection proerties
virtio-gpu:
- use generic fbdev emulation
tilcdc:
- cpufreq vs crtc init fix
rcar-du:
- R8A774C0 support
- D3/E3 RGB output routing fixes and DPAD0 support
- RA87744 LVDS support
bochs:
- atomic and generic fbdev emulation
- ID mismatch error on bochs load
meson:
- remove firmware fbs"
* tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits)
drm/amd/display: Use vrr friendly pageflip throttling in DC.
drm/imx: only send commit done event when all state has been applied
drm/imx: allow building under COMPILE_TEST
drm/imx: imx-tve: depend on COMMON_CLK
drm/imx: ipuv3-plane: add zpos property
drm/imx: ipuv3-plane: add function to query atomic update status
gpu: ipu-v3: prg: add function to get channel configure status
gpu: ipu-v3: pre: add double buffer status readback
drm/amdgpu: Bump amdgpu version for context priority override.
drm/amdgpu/powerplay: fix typo in BACO header guards
drm/amdgpu/powerplay: fix return codes in BACO code
drm/amdgpu: add missing license on baco files
drm/bochs: Fix the ID mismatch error
drm/nouveau/dmem: use dma addresses during migration copies
drm/nouveau/dmem: use physical vram addresses during migration copies
drm/nouveau/dmem: extend copy function to allow direct use of physical addresses
drm/nouveau/svm: new ioctl to migrate process memory to GPU memory
drm/nouveau/dmem: device memory helpers for SVM
drm/nouveau/svm: initial support for shared virtual memory
drm/nouveau: prepare for enabling svm with existing userspace interfaces
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxde0wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JWRB/9aQsLR22dNvKosiitTO/nnnPw/sUiG
cFZsI4G1mFpjXyC2azaY1MQOIjRZY3WDsRjcHtAJUkdJnz8fdyj74mIRoHrQI/yv
qdc7EtV5J0k0DemDQH2z5J7WjrkLg4aQCMT2XIvwrXL44jBv/iVKUE8l08D2AZ6t
hQiVIF/9iBnaJwqfUSKzJaufdd88Onh1dBljLGwZnRDtG9mndpxoi+S9pR6gwSMG
JzbgO4kUXdN95wKPxDsHFZimiSaX4bBo2cr79cisPrvcIKTyMAdtkAoNAcyuRezx
qiN2l4zz6Wxi8TygkBZfmWGKz2/2fMDWLvYwfEnA9PhddlSUZt/P1IPl
=tkEF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.1
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
In order to support the HDMI2.0 YUV420 display modes, this patch
adds support for the YUV420 TMDS Clock divided by 2 and the controller
passthrough mode.
YUV420 Synopsys PHY support will need some specific configuration table
to support theses modes.
This patch is based on work from Zheng Yang <zhengyang@rock-chips.com> in
the Rockchip Linux 4.4 BSP at [1]
[1] https://github.com/rockchip-linux/kernel/tree/release-4.4
Cc: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-5-git-send-email-narmstrong@baylibre.com
Add support for SCDC Setup for TMDS Clock > 3.4GHz and enable TMDS
Scrambling when supported or mandatory.
This patch also adds an helper to setup the control bit to support
the high TMDS Bit Period/TMDS Clock-Period Ratio as required with
TMDS Clock > 3.4GHz for HDMI2.0 3840x2160@60/50 modes.
These changes were based on work done by Huicong Xu <xhc@rock-chips.com>
and Nickey Yang <nickey.yang@rock-chips.com> to support HDMI2.0 modes
on the Rockchip 4.4 BSP kernel at [1]
[1] https://github.com/rockchip-linux/kernel/tree/release-4.4
Cc: Nickey Yang <nickey.yang@rock-chips.com>
Cc: Huicong Xu <xhc@rock-chips.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-2-git-send-email-narmstrong@baylibre.com
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
The use of drmP.h is discouraged and removal of it from
drm_modeset_helper.h caused cdns to fail to build.
This patch introduce the necessary fixes to prepare for the
drmP.h removal from drm_modeset_helper.h.
Build tested on arm x86 and arm allmodconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190119084014.5355-5-sam@ravnborg.org
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXD+OHgAKCRDj7w1vZxhR
xe3IAP4s59sFVMZseVJpwSe41OJ1ipD/cyIbtXU94X6nFd6zCAD+Jm4q+XIIS+uv
7ElmJ2BD7rwicqSViWNG8tteHYfjrAU=
=XPsb
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
[airlied: patch rcar-du to add drm_modes.h]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190116200428.u2n4jbk4mzza7n6e@flea
The call of snd_pcm_suspend_all() & co became superfluous since we
call it in the PCM PM ops. Let's remove them.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.
v2: Make is_hdmi2_sink() return true for sil-sii8620
Adapt to omap/vc4 changes
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com
drmP.h is an relic from the days when there was a single header file.
To enable the removal of drmP.h from all users drop include
of drmP.h from bridge/dw_hdmi.h.
A few files relied on the file included in drmP.h - add explicit
include statements or forward declarations to these files.
Build tested with arm and x86.
v2:
- prefer forward declarations when possible (Laurent Pinchart)
- sort include files (Laurent Pinchart)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108192939.15255-7-sam@ravnborg.org
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXDOTqAAKCRDj7w1vZxhR
xZ8QAQD4j8m9Ea3bzY5Rr8BYUx1k+Cjj6Y6abZmot2rSvdyOHwD+JzJFIFAPZjdd
uOKhLnDlubaaoa6OGPDQShjl9p3gyQE=
=WQGO
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-07-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: applied amdgpu merge fixup]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107180333.amklwycudbsub3s5@flea
tc358767 driver sets the connector type always to eDP.
This patch sets the type to DP if there is no panel defined, which
implies that there's a DP connector on the board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-8-tomi.valkeinen@ti.com
The H and V syncs of the DP output are always set to active high. This
patch fixes the syncs by configuring them according to the videomode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-7-tomi.valkeinen@ti.com
The current driver accepts any videomode with pclk < 154MHz. This is not
correct, as with 1 lane and/or 1.62Mbps speed not all videomodes can be
supported.
Add code to reject modes that require more bandwidth that is available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-6-tomi.valkeinen@ti.com
Initially DP0_SRCCTRL is set to a static value which includes
DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of
1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number.
This patch changes the configuration as follows:
Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct
value.
DP1_SRCCTRL needs two bits to be set to the same value as DP0_SRCCTRL:
SSCG and BW27. All other bits can be zero.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-5-tomi.valkeinen@ti.com
tc358767 driver does not set DRM bus_flags, even if it does configures
the polarity settings into its registers. This means that the DPI source
can't configure the polarities correctly.
Add sync flags accordingly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-2-tomi.valkeinen@ti.com
This patch unifies the naming of DRM functions for reference counting as
requested on Documentation/gpu/todo.rst
Signed-off-by: Fernando Ramos <greenfoo@gluegarage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181115221634.22715-6-greenfoo@gluegarage.com
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
It turns out that even new DW HDMI controllers exhibits same magenta
line issues as older versions.
Enable workaround for v2.12a.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-15-jernej.skrabec@siol.net
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
Right now the host is only unregistered when the driver is used via the
bridge api and not via the component api, leading to the host staying
registered in cases like probe deferral.
So move the host unregister to the general remove function, so that it
gets cleaned up in all cases.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-2-heiko@sntech.de
Let's solve the mystery of commit bf1178c989 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()"). Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.
Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational. This time is specced as 0 - 200
ms. The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.
Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted. That very closely matches the magic 70 ms
delay that we had. ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).
To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!). This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)". Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms. The extra 100 ms
(presumably) comes from this part in the datasheet:
> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.
Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").
If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it. Given
the silly debouncing in the bridge chip, though, it seems unlikely.
One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up. In theory that would let me detect _exactly_ when I could
continue and do link training. Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors. Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
This patch avoids that building the bridge/analogix source code with
smatch triggers complaints about inconsistent indenting. It also fixes
a typo in DRM_ERROR message, attch is replaced for attach.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016095336.15656-1-enric.balletbo@collabora.com
It's the default. The exported version was kinda a transition state,
before we made this the default.
To stop new atomic drivers from using it (instead of just relying on
the default) let's unexport it.
v2: rename the default implementation to a more fitting name and add a
comment (Laurent)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Pierre-Hugues Husson <phh@phh.me>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004202446.22905-3-daniel.vetter@ffwll.ch
In some IP implementations the reading of the phy-type may be broken.
One example are the Rockchip rk3228 and rk3328 socs that use a separate
vendor-type phy from Innosilicon but still report the HDMI20_TX type.
So allow the glue driver to force the vendor-phy for these cases.
In the future it may be necessary to allow forcing other types, but
for now we'll keep it simply to the case actually seen in the wild.
changes in v3:
- only allow forcing vendor type, as suggested by Laurent
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Zheng Yang <zhengyang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-2-heiko@sntech.de
Link: https://patchwork.freedesktop.org/patch/msgid/20180912124740.20343-3-heiko@sntech.de
