With KMS, we can simply relinquish the fence when we idle the GPU and
reassign it upon first use.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Avoid evicting buffers that will be used later in the batch in order to
make room for the initial buffers by pinning all bound buffers in a
single pass before binding (and evicting for) fresh buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This used to check the precondition that all fences were to be located
in a mappable area, redundant now as those two parameters are combined
into one.
After pinning, we assert that the buffer is bound into the desired
region.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pipe control object is allocated by the device for the sole use of the
render ringbuffer. Move this detail from the general code to the render
ring buffer initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Having seen the effects of erroneous fencing on the batchbuffer, a
useful sanity check is to record the fence registers at the time of an
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Combining map_and_fenceable revealed a bug in
i915_gem_object_gtt_size() in that it always computed the appropriate
fence size for the object regardless of tiling state which caused us to
over-allocate linear buffers when binding to the GTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This still uses the agp functions to actually reinstate the mappings
(with a gross hack to make agp cooperate), but it wires everything
up correctly for the switchover.
The call to agp_rebind_memory can be dropped because all non-kms drivers
do all their rebinding on EnterVT.
v2: Be more paranoid and flush the chipset cache after restoring gtt
mappings.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is required to restore gtt mappings on resume when agp is gone.
The right way to do this would be to make sturct drm_mm_node embeddable
and use the allocation list maintained by the drm memory manager. But
that's a bigger project. Getting rid of the per bo agp_mem will save
more memory than this wastes, anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
No longer used.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently if we hit a pagefault when applying a user relocation for the
execbuffer, we bail and return EFAULT to the application. Instead, we
need to unwind, drop the dev->struct_mutex, copy all the relocation
entries to a vmalloc array (to avoid any potential circular deadlocks
when resolving the pagefault), retake the mutex and then apply the
relocations. Afterwards, we need to again drop the lock and copy the
vmalloc array back to userspace.
v2: Incorporate feedback from Daniel Vetter.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GATT is a write-only set of registers, reading from them in the
manner of i915_gtt_to_phys() is supposed to be undefined. However a
simple solution exists as we allocate linear memory from the stolen
area, we can simply add the block offset to the base register. As a
side-effect we recover all the unused stolen GTT entries and so enlarge
our aperture.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After a GPU reset, the backlight controller registers may be also reset
to 0. In that case we should restore those to the original values
programmed by the BIOS. Note that we still lack the code to handle the
case where the BIOS failed to program those registers at all...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
We were reading our 64-bit value in I915_READ64 and returning 32 bits
of it. The restoration of fence regs at resume then had a zero end
value, and the fence had no effect.
Version 2: Split register access functions into per-size versions
Sharing code between different sizes seemed reasonable when we only
needed a single copy, but as 64-bit access requires its own version,
it makes sense to just split them out for each size.
Reported-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: use a macro to create the various read/write routines]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This has proven sufficient to recover from a hang of the GPU using the
gem_bad_blit test while at the KMS console then starting X. When
attempting the same during an X session, the timer doesn't appear to
trigger.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pinned buffers are useful for diagnosing errors in setting up state
for the chipset, which may not necessarily be 'active' at the time of
the error, e.g. the cursor buffer object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I had removed this when I switched the atom indirect io methods
to use the io bar rather than the mmio bar, but it appears it's
still needed.
Reported-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Under KMS, restoring the cursor is handled upon modeswitch in order to
avoid enabling an undefined set of registers. At the moment, the cursor
is restored before the aperture and modes are fully setup causing some
invalid access during resume, such as:
PGTBL_ER: 0x00040000
Invalid GTT entry during Cursor Fetch
Fix this by only performing cursor register save/restore under UMS where
it is done in the correct sequence.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Disable FBC on Ironlake to save 1W
drm/i915: Take advantage of auto-polling CRT hotplug detection on PCH hardware
drm/i915/crt: Introduce struct intel_crt
drm/i915: Do not hold mutex when faulting in user addresses
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
drm/i915: Retire any pending operations on the old scanout when switching
drm/i915: Fix I2C adapter registration
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (40 commits)
drm/radeon/kms: i2c s/sprintf/snprintf/g for safety
drm/radeon/kms: fix i2c pad masks on rs4xx
drm/ttm: Fix up a theoretical deadlock
drm/radeon/kms: fix tiling info on evergreen
drm/radeon/kms: fix alignment when allocating buffers
drm/vmwgfx: Fix up an error path during bo creation
drm/radeon/kms: register an i2c adapter name for the dp aux bus
drm/radeon/kms/atom: add proper external encoders support
drm/radeon/kms/atom: cleanup and unify DVO handling
drm/radeon/kms: properly power up/down the eDP panel as needed (v4)
drm/radeon/kms/atom: set sane defaults in atombios_get_encoder_mode()
drm/radeon/kms: turn the backlight off explicitly for dpms
drm/radeon/kms: fix typo in r600 cs checker
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
...
Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds found that it was rather trivial to trigger a system
freeze:
In fact, with lockdep, I don't even need to do the sysrq-d thing: it
shows the bug as it happens. It's the X server taking the same lock
recursively.
Here's the problem:
=============================================
[ INFO: possible recursive locking detected ]
2.6.37-rc2-00012-gbdbd01a #7
---------------------------------------------
Xorg/2816 is trying to acquire lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
other info that might help us debug this:
2 locks held by Xorg/2816:
#0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
#1: (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b
This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex. the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As per advice from Jean Delvare.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A process suspended waiting for a higher sequence or no sequence to unreserve,
a bo may be beaten to the reservation by a process with a lower sequence.
In that case the first process should give up trying to reserve and
return -EAGAIN. In order for that to happen, we must wake waiting processes
when we change sequence, so that they have a chance to detect the new
sequence.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (25 commits)
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
drm/nouveau: Return error from nouveau_gpuobj_new if we're out of RAMIN.
drm/nouveau: Fix compilation issues in nouveau_pm when CONFIG_HWMON is not set
drm/nouveau: Don't use load detection for connector polling.
drm/nv10-nv20: Fix instability after MPLL changes.
drm/nv50: implement possible workaround for NV86 PGRAPH TLB flush hang
drm/nouveau: Don't poll LVDS outputs.
drm/nouveau: Use "force" to decide if analog load detection is ok or not.
drm/nv04: Fix scanout over the 16MB mark.
drm/nouveau: fix nv40 pcie gart size
drm/nva3: fix overflow in fixed point math used for pll calculation
drm/nv10: Balance RTs expected to be accessed simultaneously by the 3d engine.
drm/nouveau: Expose some BO usage flags to userspace.
drm/nouveau: Reduce severity of the unknown getparam error.
drm/nouveau: Avoid lock dependency between ramht and ramin spinlocks.
drm/nouveau: Some random cleanups.
...
We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations. It does not contain the bank info. Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This causes the connector to not be added since i2c init fails
for the adapter. Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31688
Noticed by Ari Savolainen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Ari Savolainen <ari.m.savolainen@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle all the various asic family specific things for DVO.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.
v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP. Return something sane instead based on
the encoder id. This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like a typo in:
drm/radeon/r600: fix tiling issues in CS checker.
(f30df2fad0)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code generated an interrupt storm bad enough to completely
take down my system.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Avoid confusing userspace by not publishing backlight controls if ACPI
equivalents are available.
Reported-by: Aaron Sowry <aaron@aeneby.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Improvements:
- Fix bug in switch statement
- Add parts of 0x10022c, 0x10023c
- Clean up 0x100234
- Comment out assumption in 0x100228 until verified
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Tomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Tomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Analog output polling makes GL programs jerky when pageflip is being
used because it's carried out with the mode_config mutex held.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Nouveau sets the PCIE GART size to 64MiB for all cards before nv50,
but nv40 has enough RAMIN space to support 512MiB GART size. This
patch fixes this value to make use of this hardware capability.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will be needed for Z compression and to take smarter placement
decisions.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The ramht code called some gpuobj functions with the HARDIRQ-safe
RAMHT spinlock held, this could potentially lead to a dead lock
because ramin_lock is HARDIRQ-unsafe.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Remove some unused/duplicated definitions and make sparse happy again.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows the user to set a mode larger than the native one, useful
if we had trouble finding the actual native mode (e.g. because it goes
above the hardware bandwidth limits).
Reported-by: Grzesiek Sójka <pld@pfu.pl>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There are two messages in the ISR of nouveau which might be printed out
hundred times in a second. Ratelimit them. (We need to move
nouveau_ratelimit to the top of the file.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As we may bind an object with the correct alignment, but with an invalid
size, it may pass the current checks on whether the object may be reused
with a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
g33/pineview doesn't have any alignment constrains for unfenced tiled
buffers. But older chips have. Fix this.
Problem introduced in a00b10c360.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An old and oft reported bug, is that of the GPU hanging on a
MI_WAIT_FOR_EVENT following a mode switch. The cause is that the GPU is
waiting on a scanline counter on an inactive pipe, and so waits for a
very long time until eventually the user reboots his machine.
We can prevent this either by moving the WAIT into the kernel and
thereby incurring considerable cost on every swapbuffers, or by waiting
for the GPU to retire the last batch that accesses the framebuffer
before installing a new one. As mode switches are much rarer than swap
buffers, this looks like an easy choice.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28964
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29252
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before reading ring register, set FORCE_WAKE bit to prevent GT core
power down to low power state, otherwise we may read stale values.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: added a udelay which seemed to do the trick on my SNB]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>