But don't try to do than on pegatron tablets to avoid any
conflict.
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Let the user tells if BLED and WLED should be exposed as led or
rfkill (the old sysfs are still here, but this adds a standard
interface to control the device).
For example on my A6JC, with WAPF=1, I would do:
$ modprobe asus-laptop wled_type=led bluetooth_type=rfkill
There is still no known way to automatically guess what BLED
and WLED methods will control, it's why user information is needed.
A userspace database could do that automatically, and maybe some DMI
matching in the driver.
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add three new rfkill switches in this driver that are specific to
Pegatron Lucid tablet.
Please note that you might not need all three switches. For example if
you don't have a 3G module inside your tablet.
Also, on my device, the gpio for the wifi/bt module is connected to the
bluetooth line. Therefore to activate your wireless lan interface, you
need to use the "pega-bt" rfkill switch.
Finally, the rfkill switch only works before the wireless module is
loaded the first time. Unloading ath9k doesn't help, a reboot is
necessary.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Support the built-in accelerometer on the Lucid tablets as a standard
3-axis input device.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
device_create returns &struct device pointer on success, or ERR_PTR() on error.
Thus if led_classdev_register fails, led_cdev->dev is always not NULL.
Thus to unregister a successful registered led_classdev, we should check
IS_ERR_OR_NULL macro for led_cdev->dev instead of checking if led_cdev->dev
is NULL or not.
we use IS_ERR_OR_NULL instead of IS_ERR because if we havn't call
led_classdev_register, the led_cdev->dev is NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ambient light sensor for Pegatron Lucid. Supports pre-existing
ls_switch sysfs interface to en/disable automatic control, and exports
the brightness from the device as "ls_value".
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Recognize the Pegatron Lucid tablets by their method signatures.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add pr_fmt, prefixes each log message.
Convert printks to pr_<level>.
Convert pr_warning to pr_warn.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
I should have done that one year ago, so it's more than
time to do it.
These two features use non-standard interfaces. There are the
only features that really need multiple path to guess what's
the right method name on a specific laptop.
Removing them allow to remove a lot of code an significantly
clean the driver.
This will affect the backlight code which won't be able to know
if the backlight is on or off.
The platform display file will also be write only (like the one
in eeepc-laptop).
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Asus took the DSDT from another model (L84F), made some change
to make it work, but forgot to remove WLED method (the laptop
doesn't have a wireless card). They even didn't change the model
name.
ref: https://bugzilla.kernel.org/show_bug.cgi?id=25712
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Asus UL30A has a 3G chip, but the radio is disabled by default.
The DSDT also reference a WIMAX device, which is not present on this model.
This patch adds two new files: wwan and wimax to control WWAN and
WIMAX devices. It does not use rfkill, because like WLED and BLED,
we don't know yet that the two ACPI functions will always control the
radio, they may control only the leds on some hardware.
We may add rfkill switchs later.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
backlight_device_register has been expecting a const "ops" argument, and using
it as such, since 9905a43b2d. Let's make the
remaining backlight_ops instances const.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of registering (and removing) every attribute individually
switch to using sysfs attribute group. This makes sure that we
properly unwind and do not try to remove non-existent attributes which
may not be safe to do in the future.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The driver uses sparse keymap library and does not use this field
anymore.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The GPS rfkill crappy code. The ops_data argument wasn't
set, and was totally misused. The fix have been tested
on an Asus R2H.
Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Makes asus-laptop and eeepc-laptop _init/_exit functions
looks exactly the same as they do the same thing.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch includes below fixes:
1. return -ENOMEM instead of 0 if input_allocate_device fail.
2. fix wrong goto if sparse_keymap_setup fail.
3. fix wrong goto if input_register_device fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The wapf module parameters defines the behavior of the Fn+Fx wlan key.
The wlan_status and bluetooth_status module parameters are for setting the
wlan/bluetooth status on boot.
All above module parameters are determinated only at the module load time.
Change the value after the module is loaded does not make sense and has
no effect at all, thus set the permissions to 0444 instead of 0644.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In current implementation, store_ledd() does not return error if
write_acpi_int fail. This patch fixes it by return -ENODEV if
write_acpi_int fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
According to the comments of write_acpi_int_ret(), write_acpi_int_ret()
should return 0 if write is successful, -1 else. Thus if handle is NULL,
the write does not happen, it should return -1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The callers of write_acpi_int_ret() pass ACPI_ALLOCATE_BUFFER,
the caller must kfree the returned buffer if AE_OK is returned.
This patch adds a missing kfree(buffer.pointer) before return -ENOMEM
if kstrdup fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We were storing -1 as an unsigned int and as a result the effect of
passing -1 was the same as using 1.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
In function 'asus_laptop_get_info':
warning: passing argument 3 of 'asus_handle_init' from incompatible pointer type
note: expected 'char **' but argument is of type 'const char **'
Introduced by commit c21085108a02e1b838c34f3650c8cc9fbd178615
("asus-laptop: fix style problems reported by checkpath.pl").
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
There is two reason to do that:
- we don't want a "gps" file if the model doesn't have a gps
- we don't want to use global variables anymore
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
There is no way to find the initial lcd state. A quick workaround
is to set it "on" by default. Anyway this feature is scheduled for removal.
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
We don't want to send KEY_BRIGHTNESSDOWN or KEY_BRIGHTNESSUP
because it would be a lie to tell userspace that we want
to change the brightness while it's actually done by the
firmware.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Corentin Chary