Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Leverage the block manager's read_only flag instead of duplicating it;
access with new dm_bm_is_read_only() method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c2059 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use BLK_MQ_RQ_QUEUE_BUSY to requeue a blk-mq request directly from the
DM blk-mq device's .queue_rq. This cleans up the previous convoluted
handling of request requeueing that would return BLK_MQ_RQ_QUEUE_OK
(even though it wasn't) and then run blk_mq_requeue_request() followed
by blk_mq_kick_requeue_list().
Also, document that DM blk-mq ontop of old request_fn devices cannot
fail in clone_rq() since the clone request is preallocated as part of
the pdu.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based DM on blk_mq device, request cloning and
remapping are done in a single call to target's clone_and_map_rq().
The clone is allocated and valid only if clone_and_map_rq() returns
DM_MAPIO_REMAPPED.
The "IS_ERR(clone)" check in map_request() does not cover all the
!DM_MAPIO_REMAPPED cases that are possible (E.g. if underlying devices
are not ready or unavailable, clone_and_map_rq() may return
DM_MAPIO_REQUEUE without ever having established an ERR_PTR). Fix this
by explicitly checking for a return that is not DM_MAPIO_REMAPPED in
map_request().
Without this fix, DM core may call setup_clone() for a NULL clone
and oops like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
IP: [<ffffffff81227525>] blk_rq_prep_clone+0x7d/0x137
...
CPU: 2 PID: 5793 Comm: kdmwork-253:3 Not tainted 4.0.0-nm #1
...
Call Trace:
[<ffffffffa01d1c09>] map_tio_request+0xa9/0x258 [dm_mod]
[<ffffffff81071de9>] kthread_worker_fn+0xfd/0x150
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071fdd>] kthread+0xe6/0xee
[<ffffffff81093a59>] ? put_lock_stats+0xe/0x20
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
[<ffffffff814c2d98>] ret_from_fork+0x58/0x90
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
Fixes: e5863d9ad ("dm: allocate requests in target when stacking on blk-mq devices")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.0+
Without kicking queue, requeued request may stay forever in
the queue if there are no other I/O activities to the device.
The original error had been in v2.6.39 with commit 7eaceaccab
("block: remove per-queue plugging"), which replaced conditional
plugging by periodic runqueue.
Commit 9d1deb83d4 in v4.1-rc1 removed the periodic runqueue
and the problem started to manifest.
Fixes: 9d1deb83d4 ("dm: don't schedule delayed run of the queue if nothing to do")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is a set of five fixes: Two MAINTAINER email updates (urgent because the
non-avagotech emails will start bouncing) an lpfc big endian oops fix, a 256
byte sector hang fix (to eliminate 256 byte sectors) and a storvsc fix which
could cause test unit ready failures on bringup.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVYPemAAoJEDeqqVYsXL0MK8UIAJJ8ViLPTfhweb8QgHsUjc4S
5x2jPUD69XT93G81NWKvFhYBnlAvktBZuy6uON7SkLWkbwgiu3pB1Iowqie+Z/h8
1C5VwC8oaT6GZPuakRRxnYmoAaCX7kbdMsibSvc5ouTgvM5FdailhJpkDKcFQlkn
t1GqmRQyH1P54O73af2d+z3AfNfivjoFFXz1YHcUOouiKBVyXzqk1c3CIwTQMelg
B547Rz2cqgdDtgQzZzPkfust/GOYs0ZQMU3rhjeNyIvw/5xa0/Ta2m/v16lckV2I
AvjK2Ht5XSr/Hc9m4yvr5vYCT5+mVrebYMghnUqpHjx1OGTBSU9lPT0exbCCJ/o=
=lXOs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Pull irqchip fix from Thomas Gleixner:
"A fix for a GIC-V3 irqchip regression which prevents some systems from
booting"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
- one serious RAID0 data corruption - caused by recent bugfix that wasn't
reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jXKM
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dm-multipath has to clone the bios for every request sent
to the lower devices, which wastes cpu cycles and ties down memory.
This patch instead adds a new REQ_CLONE flag that instructs req_bio_endio
to not complete bios attached to a request, which we set on clone
requests similar to bios in a flush sequence. With this change I/O
errors on a path failure only get propagated to dm-multipath, which
can then either resubmit the I/O or complete the bios on the original
request.
I've done some basic testing of this on a Linux target with ALUA support,
and it survives path failures during I/O nicely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for
non-chains") regressed all existing callers that followed this pattern:
1) saving a bio's original bi_end_io
2) wiring up an intermediate bi_end_io
3) restoring the original bi_end_io from intermediate bi_end_io
4) calling bio_endio() to execute the restored original bi_end_io
The regression was due to BIO_CHAIN only ever getting set if
bio_inc_remaining() is called. For the above pattern it isn't set until
step 3 above (step 2 would've needed to establish BIO_CHAIN). As such
the first bio_endio(), in step 2 above, never decremented __bi_remaining
before calling the intermediate bi_end_io -- leaving __bi_remaining with
the value 1 instead of 0. When bio_inc_remaining() occurred during step
3 it brought it to a value of 2. When the second bio_endio() was
called, in step 4 above, it should've called the original bi_end_io but
it didn't because there was an extra reference that wasn't dropped (due
to atomic operations being optimized away since BIO_CHAIN wasn't set
upfront).
Fix this issue by removing the __bi_remaining management complexity for
all callers that use the above pattern -- bio_chain() is the only
interface that _needs_ to be concerned with __bi_remaining. For the
above pattern callers just expect the bi_end_io they set to get called!
Remove bio_endio_nodec() and also remove all bio_inc_remaining() calls
that aren't associated with the bio_chain() interface.
Also, the bio_inc_remaining() interface has been moved local to bio.c.
Fixes: c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for non-chains")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just two small DP fixes for 4.1
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
Pull thermal fixes from Zhang Rui:
"Three fixes for Armada (380) and TI (dra7 and OMAP5) thermal soc
drivers"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: armada: Update Armada 380 thermal sensor coefficients
thermal: ti-soc-thermal: OMAP5: Implement Workaround for Errata i813
thermal: ti-soc-thermal: dra7: Implement Workaround for Errata i814
A number of small, well contained bug fixes for ocrdma driver
A simple fix for the connection negotiation sequence on IB
Fix for broken AF_IB address on UD queue pair support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=L53a
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull infiniband/rdma fixes from Doug Ledford:
"This should hopefully be the last request for 4.1-rc for the RDMA
stack. It contains some late ocrdma fixes that I'm including because
they are small and self contained. It also contains two bug fixes
that are simple and easily verified.
Summary:
- a number of small, well contained bug fixes for ocrdma driver
- a simple fix for the connection negotiation sequence on IB
- fix for broken AF_IB address on UD queue pair support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cma: Fix broken AF_IB UD support
ib/cm: Change reject message type when destroying cm_id
RDMA/ocrdma: Update ocrdma version number
RDMA/ocrdma: Fail connection for MTU lesser than 512
RDMA/ocrdma: Fix dmac resolution for link local address
RDMA/ocrdma: Prevent allocation of DPP PDs if FW doesnt support it
RDMA/ocrdma: Fix the request length for RDMA_QUERY_QP mailbox command to FW.
RDMA/ocrdma: Use VID 0 if PFC is enabled and vlan is not configured
RDMA/ocrdma: Fix QP state transition in destroy_qp
RDMA/ocrdma: Report EQ full fatal error
RDMA/ocrdma: Fix EQ destroy failure during driver unload
- atmel-mci: fix bad variable type for clkdiv
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9Ju7
-----END PGP SIGNATURE-----
Merge tag 'mmc-4.1-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fix from Ulf Hansson:
"One more mmc fix intended for v4.1 rc5:
MMC host:
- atmel-mci: fix bad variable type for clkdiv"
* tag 'mmc-4.1-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: atmel-mci: fix bad variable type for clkdiv
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
exception of a single locking fix in the core code. All driver fixes are
for code that was merged recently. The Samsung stuff is mostly fixes
around suspend/resume, the Qualcomm fixes are for invalid hardware
configuration data and the Silicon Labs patches are fixes following
their move away from platform_data to Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yjsw
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
That atom table does not check these bits. Fixes aux
regressions on some boards.
Reported-by: Malte Schröder <malte@tnxip.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The index of ->planes[] array (3rd parameter) cannot be equal to MAX_PLANE.
This looks like a typo that is now fixed.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Evaluating "&mddev->disks" is simple pointer arithmetic, so
it does not need 'rcu' annotations - no dereferencing is happening.
Also enhance the comment to explain that 'rdev' in that case
is not actually a pointer to an rdev.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The variable "sector" in "raid0_make_request()" was improperly updated
by a call to "sector_div()" which modifies its first argument in place.
Commit 47d68979cc restored this variable
after the call for later re-use. Unfortunetly the restore was done after
the referenced variable "bio" was advanced. This lead to the original
value and the restored value being different. Here we move this line to
the proper place.
One observed side effect of this bug was discarding a file though
unlinking would cause an unrelated file's contents to be discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 47d68979cc ("md/raid0: fix bug with chunksize not a power of 2.")
Cc: stable@vger.kernel.org (any that received above backport)
URL: https://bugzilla.kernel.org/show_bug.cgi?id=98501
ops_run_reconstruct6() doesn't correctly chain asyn operations. The tx returned
by async_gen_syndrome should be added as the dependent tx of next stripe.
The issue is introduced by commit 59fc630b8b
RAID5: batch adjacent full stripe write
Reported-and-tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The vmmouse Kconfig help text was referring to an incorrect user-space
driver version. Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1221200
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com>
Signed-off-by: Matt Finlay <matt@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When allocating a device table, if the requested allocation is smaller
than the default granule size of the ITS then, we need to round up to
the default size.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[ stuart: Added comments and massaged changelog ]
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Reviewed-by: Marc Zygnier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1432134795-661-1-git-send-email-stuart.yoder@freescale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
