We must not assert reset for modules with no child device drivers
until in runtime_suspend. Otherwise register access will fail without
legacy mode helping us.
Let's add a flag for disable_on_idle and move the reset driver
handling to runtime suspend and resume. We can then also use the
disable_on_idle flag to reconfigure sysconfig register for PM
modes requesting it.
Let's also make the other flags use bitfield while at it instead of
bool.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have ENAWAKEUP bit that we need to configure when not
relying on platform data callbacks.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have idlemodes wired, but not completely functional. We have
quirks for SWSUP_SIDLE and SWSUP_SIDLE_ACT to manage interconnect target
modules without hardware support, but we've been only using them so far
in legacy mode. Let's add support for SWSUP quirks in non-legacy mode too.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For interconnect target modules with autoidle bit wired, we need to manage
it for enable and disable.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to specify QUIRK_LEGACY_IDLE for device drivers that still have
pm_runtime_irq_safe() set like 8250.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had minimal OCP softreset support in ti-sysc interconnect target
module driver only used for MCAN driver so far. But it turns out that
MCAN has the sysstatus register resetdone bit inverted compared to most
other modules.
Let's make OCP softreset work for other typical cases with reset status
in sysstatus or sysconfig register so we can use the new functions for
sysc_enable_module() and sysc_disable_module() without "ti,hwmods"
property in the following patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to also support 16-bit writes for i2c in addition to the reads
when we start configuring the sysconfig register for reset and idle modes.
Note that only i2c revision register has LO and HI registers, so let's
add a check also for 16-bit register read. This change is currently cosmetic
and does not affect anything until we enable the module specific quirk
handling for i2c reset and enable later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to let ti-sysc driver manage clockdomain autoidle for the
duration of of reset, enable and idle. And we need to do it before we
enable the clock and after we disable it. Currently we are still
relying on platform callbacks indirectly managing clockdomain autoidle.
But I noticed that for device tree only probed drivers it now happens
only after we enabling the clocks and before we disable the clocks,
while it should be the other way around. So far I have not noticed
any issues with this though.
Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle()
functions for ti-sysc driver to use to manage clockdomains directly via
platform data callbacks. Note that we can implement the clockdomain
functions in pdata-quirks.c as for probing devices without "ti,hwmods"
custom property we don't need to use the other platform data callbacks.
Let's do this in one patch as there's is still an unlikely chance we
may need to apply this as a fix for v5.2 for dropping legacy platform
data for some devices. We also do have the option of adding back the
platform data if needed in case of trouble.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some interconnect target modules have no module control registers at
all, such as d_can on am335x and am437x.
The d_can register offset at 0 is CTL register with 0x401 as the default
value. I guess I mistook the 0x401 value for a revision register as the
value happens to look similar to what the revision registers typically
have for other modules.
To handle modules with no control registers, we need to improve the
ti-sysc driver a bit to bail out with errors on no control registers,
and then we can remove the bogus revision registers for d_can.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For non legacy cases, add generic sysc_enable_module()
and sysc_disable_module() functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.
For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least mcpdm needs an optional external clock enabled to function and
this clock typically comes from the PMIC. We can detect mcpdm based on
the interconnect target module address and set a quirk flag early.
To do this, let's initialize the clocks a bit later and add a new
function for sysc_init_early_quirks(). Note that we cannot yet enable
the early quirks for mcpdm until the optional external clocks are
handled in the in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can do the rsstctrl a bit later, but need to deassert rstctrl reset
before the clocks are enabled if asserted. Let's only init restctrl
in sysc_init_resets() and do the reset later on just before we enable
the device clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently not managing interconnect target module clocks in the
for legacy platform data based case. This causes a problem for using the
platform data based functions when dropping the platform data for the
interconnect target module configuration.
To avoid a situation where we need to populate the main and optional
clocks also for the platform data based functions, let's just manage the
clocks directly in ti-sysc driver. This means that until the interconnect
target module confugration platform data is dropped our use count for
clk_enable() will be 2 instead of 1.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data based init functions typically reset the interconnect
target module configure the registers. As we may need the interconnect
target module specific quirks configured based on the revision register,
we want to move the platform data based init to happen later.
Let's allocate mdata as needed so it's available for sysc_legacy_init()
that we call with module clocks enabled from sysc_init_module().
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.
As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.
To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least McPDM module depends on an external optional clock to be
usable. To make handling of the McPDM clock easier in the following
patches, let's add separate functions for handling the main clocks
and the optional clocks.
Let's also add error handling to shut down already enabled clocks
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.
Let's also group the idle defines together and update the binding
documentation for it.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") started producing a warning for pwm-omap-dmtimer:
WARNING: CPU: 0 PID: 77 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x2f8/0x388
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4PER2 (Idle):
Data Access in Supervisor mode during Functional access
...
__pm_runtime_idle
omap_dm_timer_disable
pwm_omap_dmtimer_start
pwm_omap_dmtimer_enable
pwm_apply_state
pwm_vibrator_start
pwm_vibrator_play_work
This is because the timer that pwm-omap-dmtimer is using is now being
probed with ti-sysc interconnect target module instead of omap_device
and the ti-sysc quirk for SYSC_QUIRK_LEGACY_IDLE is not fully
compatible with what omap_device has been doing.
We could fix this by reverting the timer changes and have the timer
probe again with omap_device. Or we could add more quirk handling to
ti-sysc driver. But as these options don't work nicely as longer term
solutions, let's just make timers probe with ti-sysc without any
quirks.
To do this, all we need to do is remove quirks for timers for ti-sysc,
and drop the bogus pm_runtime_irq_safe() flag for timer-ti-dm.
We should not use pm_runtime_irq_safe() anyways for drivers as it will
take a permanent use count on the parent device blocking the parent
devices from idling and has been forcing ti-sysc driver to use a
quirk flag.
Note that we will move the timer data to DEBUG section later on in
clean-up patches.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-By: Andreas Kemnade <andreas@kemnade.info>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have OPT_CLKS_NEEDED in legacy platform data, but it's missing
from the ti-sysc driver for device tree based configuration.
In order to pass OPT_CLKS_NEEDED quirk flag we need to update omap4 module
data and add a new compatible for dra7 as the module layout is different
from sysc_regbits_omap4_mcasp.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have holes in clock_roles with interface clock missing for
example. Currently getting an optional clock will fail if there are
only a functional clock and an optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
As Grygorii Strashko pointed out, the runtime PM use count of the
children can be whatever at suspend and we should not use it. So
let's just suspend ti-sysc at noirq level and get rid of some code.
Let's also remove the PM_SLEEP ifdef and use __maybe_unused as the
PM code already deals with the ifdefs.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We're currently warning about busy children on suspend in
sysc_child_suspend_noirq() but the legacy code omap_device does
not do that. Let's just make it dev_dbg() instead of dev_warn().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect timer and gpio on dra7 because of the
SYSC_QUIRK_LEGACY_IDLE flag for suspend and resume.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When debug is enabled, we want to see what devices we're detecting
to make things a bit easier for us. Many of these devices will also
be available on am335x and dra7, and some just need updating the
revision register mask.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect few new devices to tag for noirq_suspend and
pm_runtime_irq_safe to avoid causing regressions compared to
legacy platform data booting.
Let's update i2c, gpio, uart and wdt revision masks to detect
them on am437x. Note that we can remove the second wdt entry
with the updated mask. Note that we also have some uarts with
a different revision register.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't care when we suspend but some our children do. In order to
avoid tagging various modules with SYSC_QUIRK_RESOURCE_PROVIDER, let's
do it automatically by tagging modules that are busy on suspend for
noirq suspend. This way we can just do module detection on define DEBUG.
Note that we still need to keep SYSC_QUIRK_LEGACY_IDLE flag around so
the our legacy single-child devices that set pm_runtime_irq_safe() can
manage the interconnect target module themselves.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If no_console_suspend is set, we should keep console enabled during suspend.
Lets fix this by only producing a warning if we can't idle hardware during
suspend.
Fixes: ef55f8215a ("bus: ti-sysc: Improve suspend and resume handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have the interconnect target module control registers pretty
much anywhere within the module range. The current code attempts an
incomplete optimization of the ioremap size but does it wrong and
it only works for registers at the beginning of the module.
Let's just use the largest control register to calculate the ioremap
size. The ioremapped range is for most part cached anyways so there
is no need for size optimization. Let's also update the comments
accordingly.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect
target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the software reset of a target interconnect
module using its sysconfig and sysstatus registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[tony@atomide.com: updated to check if sysconfig exists]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dra76x MCAN generic interconnect module has a its own
format for the bits in the control registers.
Therefore add a new module type, new regbits and new capabilities
specific to the MCAN module.
Acked-by: Rob Herring <robh@kernel.org>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adjusts the allocator calls to use 2-factor argument call style, as
done treewide already for improved defense against allocation overflows.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We should be checking ddata->clocks[i] instead of clock_names[i]
for the optional clocks. Currently this just happens to work for
the typical case of one fck and one optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's show module info if DEBUG is enabled to make it easier to follow
what happens on the suspend and resume path.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like these two device drivers don't yet behave properly for suspend
unless configured with the legacy option.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Starting with omap4, UARTs have different revision register that we need to
detect to enable SYSC_QUIRK_LEGACY_IDLE. Otherwise UARTs won't idle properly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Starting with omap4 some timers have different sysc registers (type2) compared
to the omap2 timers (type1). We need to detect these to enable the quirk for
SYSC_QUIRK_LEGACY_IDLE, otherwise these won't be idling properly.
Siganed-off-by: Tony Lindgren <tony@atomide.com>
Some modules need to use external resets in the rstctrl bits. Typically
only one of the rstctrl bits is for the interconnect target module while
the others are for various child devices.
For ti-sysc driver, we just need the module rstctrl bit mapped. The rest
of the rstctrl bits can be directly mapped to the child devices.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on testing with more devices I noticed that some devices
don't suspend or resume properly. We need to PM runtime suspend
and resume devices if we have ddata->needs_resume set.
Let's also improve the error handling and add few debug statements
to make it easier to notice suspend and resume related issues if
DEBUG is set.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modules that provide resources for other modules need to be suspended
and resumed in the noirq calls. Tag the resource providing modules.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There can be up to eight optional device functional gate gate clocks for
each clkctrl instance in clkctrl register bits 8 to 15. Some of them are
only needed for module level reset while others may always be needed
during use. Let's add support for those and update the binding doc
accordingly.
Note that the optional clkctrl mux and divider clocks starting at bit 20
can be directly mapped to the child devices, and ti-sysc does not need to
manage those.
And as GPIOs need the optional clocks for reset, we can now add it with
SYSC_QUIRK_OPT_CLKS_IN_RESET.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to prepare supporting clkctrl optional clocks, we need to
make the current child clock handling more generic so we can use the
clock role names for the optional clocks in the following patch.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise child devices that some interconnect target module devices
have won't probe using simple-bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
-----BEGIN PGP SIGNATURE-----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=/hJY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Driver changes for ti-sysc for v4.17" from Tony Lindgren:
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
* tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable ti-sysc to use device tree data for smartreflex
PM / AVS: SmartReflex: Prepare to use device tree based probing
ARM: OMAP2+: Try to parse earlycon from parent too
ARM: OMAP2+: Add checks for device tree based sysconfig data
ARM: OMAP2+: Add functions to allocate module data from device tree
bus: ti-sysc: Handle some devices in omap_device compatible way
bus: ti-sysc: Add support for platform data callbacks
bus: ti-sysc: Remove unnecessary debugging statements
bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init
bus: ti-sysc: Handle stdout-path for debug console
bus: ti-sysc: Add suspend and resume handling
bus: ti-sysc: Add fck clock alias for children with notifier_block
ARM: OMAP2+: Prepare to pass auxdata for smartreflex
Now that ti-sysc can manage child devices, we must also be backwards
compatible with the current omap_device code. With omap_device, we
assume that the child device manages the interconnect target module
directly.
The drivers needing special handling are the ones that still set
pm_runtime_irq_safe(). In the long run we want to update those drivers
as otherwise they will cause problems with genpd as a permanent PM
runtime usage count is set on the parent device.
We can handle omap_device these devices by improving the ti-sysc quirk
handling to detect the devices needing special handling based on
register map and revision register if usable. We also need to implement
dev_pm_domain for these child devices just like omap_device does.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to pass the device tree configuration for interconnect target
modules from ti-sysc driver to the existing platform hwmod code.
This allows us to first validate the dts data against the existing
platform data before we start dropping the platform data in favor of
device tree data.
To do this, let's add platform data callbacks for PM runtime functions
to call for the interconnect target modules if platform data is
available.
Note that as ti-sysc driver can rebind, omap_auxdata_lookup and related
functions can no longer be __init.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We already show the status for the interconnect target module
when debugging is enabled, there's no need to be more verbose
about that. So let's just cut down the noise and remove the
extra debug statements.
Signed-off-by: Tony Lindgren <tony@atomide.coM>
At least earlycon needs a delayed idle before the 8250 driver probes
to avoid glitches in the console output. Let's handle the delayed idle
for devices tagged with ti,no-reset-on-init and ti,no-idle-on-init with
delayed_work. Others don't need it, and there should be no need to use
runtime PM autosuspend for the interconnect target driver as it's the
child device drivers that should configure it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we have stdout-path specified for earlycon, we must prevent
the debug console from idling until runtime PM kicks in.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The functional clock is used by several child device drivers to query
the rate for the child device internal configuration. The functional
clock is really for the whole interconnect target module, and not just
for the child device, and can also be shared across multiple children.
At least the timers, i2c and mmc driver query the fck for rate.
So let's just create a clock alias for the child fck if it does not
yet exits. We can do this with the BUS_NOTIFY_ADD_DEVICE before the
child is probed.
Note that we need to now also remove the legacy mode check for getting
the dts clocks in ti-sysc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently only checking for the first entry in the table while
we should check them all. Usual no-idle-on-init is together with
no-reset-on-init, so this has gone unnoticed.
Fixes: 566a9b05e1 ("bus: ti-sysc: Handle module quirks based dts
configuration")
Signed-off-by: Tony Lindgren <tony@atomide.com>
The enawakeup bit is in a different location for smartreflex compared
to the "ti,sysc-omap2" compatible.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to configure the interconnect target module based on the
device three configuration.
Let's also add a new quirk for SYSC_QUIRK_RESET_STATUS to indicate
that the SYSCONFIG reset bit changes after the reset is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's configure few module quirks via device tree using the
properties for "ti,no-idle-on-init", "ti,no-reset-on-init"
and "ti,sysc-delay-us".
Let's also reorder the probe a bit so we have pdata available
earlier, and move the PM runtime calls to sysc_init_module()
from sysc_read_revision().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can easily detect i2c based on it's non-standard module registers that
consist of two 32-bit registers accessed in 16-bit mode.
So far we don't have other 16-bit modules, so there's currently no need
to add a custom property for 16-bit register access.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add data for the known interconnect target module types by mapping
their register bits.
Note that we can handle many quirks for the older omap2 type1 modules
directly in the driver without a need for adding custom properties.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing remove() that's needed if a driver instance
rebound. Otherwise we will get "Unbalanced pm_runtime_enable!".
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new bus driver causes a harmless compile-time warning when
CONFIG_PM is disabled:
drivers/bus/ti-sysc.c:440:12: error: 'sysc_runtime_resume' defined but not used [-Werror=unused-function]
static int sysc_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/bus/ti-sysc.c:421:12: error: 'sysc_runtime_suspend' defined but not used [-Werror=unused-function]
static int sysc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
This marks the two unused functions as __maybe_unused to shut up
that warning.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can handle the sysc interconnect target module in a generic way
for many TI SoCs. Initially let's just enable runtime PM with
autosuspend, and probe the children. This can already be used for
idling interconnect target modules that don't have any device driver
available for the child devices.
For now, the "ti,hwmods" custom binding is still required. That will
be eventually deprecated in later patches. And more features will be
added, such as parsing for sysc capabilities so we can continue
removing the legacy platform data.
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
