This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
https://lkml.org/lkml/2014/7/11/794
I used it with those arguments:
$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]
It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.
Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The audio configuration in chip config register 0x00 and eeprom are always
consistent. But currently the audio configuration #defines for the chip config
register say 0x20 means 3 sample rates and 0x30 5 sample rates, while the eeprom
info output says 0x20 means 1 sample rate and 0x30 3 sample rates.
I've checked the datasheet excerpts I have and it seems that the meaning of
these bits is different for em2820/40 (1 and 3 sample rates) and em2860+
(3 and 5 smaple rates).
I have also checked my Hauppauge WinTV USB 2 (em2840) and the chip/eeprom
audio config 0x20 matches the sample rates reproted by the USB device
descriptor (32k only).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New chip version, which is very similar than EM28174.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- add definition for GPIO register 0x09 (reading/input)
- extend the information the chip variants that support GPIO registers 0x08/0x09
- rename EM28XX_R08_GPIO to EM2820_R08_GPIO_CTRL
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/7x/8x provides 4 GPIO register sets,
each of them consisting of separate read and a write registers.
The same registers are also used by the em2874/174/84.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current enpoint logic ignores all bulk endpoints and uses
a fixed mapping between endpint addresses and the supported
data stream types (analog/audio/DVB):
Ep 0x82, isoc => analog
Ep 0x83, isoc => audio
Ep 0x84, isoc => DVB
Now that the code can also do bulk transfers, the endpoint
logic has to be extended to also consider bulk endpoints.
The new logic preserves backwards compatibility and reflects
the endpoint configurations we have seen so far:
Ep 0x82, isoc => analog
Ep 0x82, bulk => analog
Ep 0x83, isoc* => audio
Ep 0x84, isoc => digital
Ep 0x84, bulk => analog or digital**
(*: audio should always be isoc)
(**: analog, if ep 0x82 is isoc, otherwise digital)
[mchehab@redhat.com: Fix a CodingStyle issue: don't break strings
into separate lines]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By disabling the NEC parity check, it is possible to handle all 3 NEC
protocol variants (32, 24 or 16 bits).
Change the driver in order to handle all of them.
Unfortunately, em2860/em2863 provide only 16 bits for the IR scancode,
even when NEC parity is disabled. So, this change should affect only
em2874 and newer devices, with provides up to 32 bits for the scancode.
Tested with one NEC-16, one NEC-24 and one RC5 IR.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-15 16:25:07 -03:00
Renamed from drivers/media/video/em28xx/em28xx-reg.h (Browse further)
