When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 2b995f6398.
Панов Андрей reported the following regression:
"Commit 2b995f6398 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array index 'j' is used before limits check.
Suggest put limit check before index use.
Signed-off-by : <Ameenali023@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't delete napi from hash list during module exit. This will
cause the following panic when doing module load and unload:
BUG: unable to handle kernel paging request at 0000004e00000075
IP: [<ffffffff816bd01b>] napi_hash_add+0x6b/0xf0
PGD 3c5d5067 PUD 0
Oops: 0000 [#1] SMP
...
Call Trace:
[<ffffffffa0a5bfb7>] init_vqs+0x107/0x490 [virtio_net]
[<ffffffffa0a5c9f2>] virtnet_probe+0x562/0x791815639d880be [virtio_net]
[<ffffffff8139e667>] virtio_dev_probe+0x137/0x200
[<ffffffff814c7f2a>] driver_probe_device+0x7a/0x250
[<ffffffff814c81d3>] __driver_attach+0x93/0xa0
[<ffffffff814c8140>] ? __device_attach+0x40/0x40
[<ffffffff814c6053>] bus_for_each_dev+0x63/0xa0
[<ffffffff814c7a79>] driver_attach+0x19/0x20
[<ffffffff814c76f0>] bus_add_driver+0x170/0x220
[<ffffffffa0a60000>] ? 0xffffffffa0a60000
[<ffffffff814c894f>] driver_register+0x5f/0xf0
[<ffffffff8139e41b>] register_virtio_driver+0x1b/0x30
[<ffffffffa0a60010>] virtio_net_driver_init+0x10/0x12 [virtio_net]
This patch fixes this by doing this in virtnet_free_queues(). And also
don't delete napi in virtnet_freeze() since it will call
virtnet_free_queues() which has already did this.
Fixes 91815639d8 ("virtio-net: rx busy polling support")
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a performance regression introduced by
7fbb9d8415 (xen-netback: release pending
index before pushing Tx responses)
Moving the notify outside of the spin locks means it can be delayed a
long time (if the dealloc thread is descheduled or there is an
interrupt or softirq).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU/vcnAAoJEG4XJFUm622bBbMIAJAmmITit1LFbm5L5zguIkVq
b9ppfEkgz6JYb4KMe6jWnvrc9yM3ywslH2Evo09ChA53A2sUhORKxlolreGTZxtQ
je3twmUCyzkbvss+aKFS4BzEDDOGwW9A/wk3LT4TZJ7Jp626k1wPXN5WZHaDh0YC
pE7fH6jnNg2Qoe68tG8WmTqrYlzU6mLpI0NNxsW+h2tK2Gqm7jSoMy96RPiwS0ZV
BFnxrJJZViMyPit48pZf338pdndkxOIlDBIJCY8qUwQIt4HxQ8DnmsLWqg9xjnfT
mSO9xgSJxfR02ZDIBYqaK41KlcharjwrF5lDi+JHkoHB2SQQM9A/noxpWu4/JGI=
=pOSK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
iwlwifi:
* fix ROC removal - avoids a firmware crash
* fix throughput regression on iwldvm devices
* fix panic in BT Coex
* fixes in rate control
* fixes in scan
b43:
* fix support for 5 GHz only BCM43228 model
rtlwifi:
* improve handling of IPv6 packets
brcmfmac:
* perform bound checking on vendor command buffer
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support receive VLAN CTAG HW acceleration feature
(NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the
api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there
have overlap between the two memory data point range. The patch just fix
the issue.
V2:
Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset().
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Fixes: 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A short or malformed vendor command buffer could cause reads outside
the command buffer.
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Pontus Fuchs <pontusf@broadcom.com>
[arend@broadcom.com: slightly modified debug trace output]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de7b5b3d79 ("net: eth: xgene: change APM X-Gene SoC platform
ethernet to support ACPI") breaks booting with devicetree with UEFI
firmware. In that case, I get:
Unhandled fault: synchronous external abort (0x96000010) at 0xfffffc0000620010
Internal error: : 96000010 [#1] SMP
Modules linked in: vfat fat xfs libcrc32c ahci_xgene libahci_platform libahci
CPU: 7 PID: 634 Comm: NetworkManager Not tainted 4.0.0-rc1+ #4
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0-rh-0.14 Mar 1 2015
task: fffffe03d4c7e100 ti: fffffe03d4e24000 task.ti: fffffe03d4e24000
PC is at xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
LR is at xgene_gmac_tx_enable+0x2c/0x50
pc : [<fffffe000069d6fc>] lr : [<fffffe000069dcc4>] pstate: 80000145
sp : fffffe03d4e27590
x29: fffffe03d4e27590 x28: 0000000000000000
x27: fffffe03d4e277c0 x26: fffffe03da8fda10
x25: fffffe03d4e2760c x24: fffffe03d49e28c0
x23: fffffc0000620004 x22: 0000000000000000
x21: fffffc0000620000 x20: fffffc0000620010
x19: 000000000000000b x18: 000003ffd4a96020
x17: 000003ff7fc1f7a0 x16: fffffe000079b9cc
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: fffffe03d4e24000
x11: fffffe03d4e27da0 x10: 0000000000000001
x9 : 0000000000000000 x8 : fffffe03d4e27a20
x7 : 0000000000000000 x6 : 00000000ffffffef
x5 : fffffe000105f7d0 x4 : fffffe00007ca8c8
x3 : fffffe03d4e2760c x2 : 0000000000000000
x1 : fffffc0000620000 x0 : 0000000040000000
Process NetworkManager (pid: 634, stack limit = 0xfffffe03d4e24028)
Stack: (0xfffffe03d4e27590 to 0xfffffe03d4e28000)
...
Call trace:
[<fffffe000069d6fc>] xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
[<fffffe000069dcc0>] xgene_gmac_tx_enable+0x28/0x50
[<fffffe00006a112c>] xgene_enet_open+0x2c/0x130
[<fffffe00007b9254>] __dev_open+0xc8/0x148
[<fffffe00007b956c>] __dev_change_flags+0x90/0x158
[<fffffe00007b9664>] dev_change_flags+0x30/0x70
[<fffffe00007c8ab8>] do_setlink+0x278/0x870
[<fffffe00007c95bc>] rtnl_newlink+0x404/0x6a8
[<fffffe00007c8040>] rtnetlink_rcv_msg+0x98/0x218
[<fffffe00007e78e4>] netlink_rcv_skb+0xe0/0xf8
[<fffffe00007c7f94>] rtnetlink_rcv+0x30/0x44
[<fffffe00007e6f2c>] netlink_unicast+0xfc/0x210
[<fffffe00007e75b8>] netlink_sendmsg+0x498/0x5ac
[<fffffe00007990b8>] do_sock_sendmsg+0xa4/0xcc
[<fffffe000079a958>] ___sys_sendmsg+0x1fc/0x208
[<fffffe000079b984>] __sys_sendmsg+0x4c/0x94
[<fffffe000079b9f8>] SyS_sendmsg+0x2c/0x3c
The problem here is that the enet hw clocks are not getting
initialized because of a test to avoid the initialization if
UEFI is used to boot. This is an incorrect test. When booting
with UEFI and devicetree, the kernel must still initialize
the enet hw clocks. If booting with ACPI, the clock hw is
not exposed to the kernel and it is that case where we want
to avoid initializing clocks.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Feng Kan <fkan@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a from-guest frag list, xenvif_handle_frag_list()
replaces the frags before calling the destructor to clean up the
original (foreign) frags. Whilst this is safe (the destructor doesn't
actually use the frags), it looks odd.
Reorder the function to be less confusing.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time a VIF is destroyed up to 256 pages may be leaked if packets
with more than MAX_SKB_FRAGS frags were transmitted from the guest.
Even worse, if another user of ballooned pages allocated one of these
ballooned pages it would not handle the unexpectedly >1 page count
(e.g., gntdev would deadlock when unmapping a grant because the page
count would never reach 1).
When handling a from-guest skb with a frag list, unref the frags
before releasing them so they are freed correctly when the VIF is
destroyed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct pointer arithmetic to get the pointer to each stat.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit below introduced an unsafe dereference of
mvmvif->phy_ctxt. It can be NULL even if we hold the mutex.
We can be handling a BT Coex notification while the vif has
already been unassigned. This can happen since the BT Coex
notification is hanled asynchronuously: we can have started
to handle the BT Coex notification trying to acquire the
mutex while the unassign flow already got it. The BT Coex
notification handling will wait for the mutext. I'll get it
later, but then mvmvif->phy_ctxt will be NULL.
Panic log:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f985180d>] iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
*pdpt = 0000000000000000 *pde = f000eef300000007
Oops: 0000 [#1] SMP
Workqueue: events iwl_mvm_async_handlers_wk [iwlmvm]
task: ed719b20 ti: ec03e000 task.ti: ec03e000
EIP: 0060:[<f985180d>] EFLAGS: 00010202 CPU: 2
EIP is at iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
EAX: 00000000 EBX: f6d3cb70 ECX: f6d3cb70 EDX: 00000000
ESI: ec03fe40 EDI: efeb8810 EBP: ec03fdf0 ESP: ec03fdac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000000 CR3: 01a1a000 CR4: 001407f0
Stack:
f743ca80 f744a404 ec03fdcc c10e3952 00003aba f743ca80 00000246 f743ca80
00000246 00000000 00000001 00000000 ebd45ff6 ebd458a4 f6d3c500 ebd45578
ebd44b01 ec03fe18 f99e1bc2 00000002 ebd44bc0 f9851770 00000000 f6d3c500
Call Trace:
[<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
[<f99e1bc2>] __iterate_interfaces+0x82/0x110 [mac80211]
[<f9851770>] ? iwl_mvm_bt_coex_reduced_txp+0x140/0x140 [iwlmvm]
[<f99e1c6a>] ieee80211_iterate_active_interfaces_atomic+0x1a/0x20 [mac80211]
[<f9851427>] iwl_mvm_bt_coex_notif_handle+0x77/0x280 [iwlmvm]
[<f9852161>] iwl_mvm_rx_bt_coex_notif_old+0x211/0x220 [iwlmvm]
[<f9850b8b>] iwl_mvm_rx_bt_coex_notif+0x19b/0x1b0 [iwlmvm]
[<f983944f>] iwl_mvm_async_handlers_wk+0x7f/0xe0 [iwlmvm]
CC: <stable@vger.kernel.org> [3.19+]
Fixes: 123f515635 ("iwlwifi: mvm: BT Coex - add support for TTC / RRC")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Commit 6ce29b0e2a ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: Alan Fisher <acf@unixcube.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
