This code has been there for nine years now, and it has been
working "good enough" since then [1].
Remove duplicate code by getting rid of the if-else statement.
[1] https://marc.info/?l=linux-kernel&m=152693550225081&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only looking at the lock register causes the status to float
between locked and not locked when there is no signal. So improve
the logic to also examine the state of the FSC PLL, which results
in the lock status being consistently reported.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I got this working a couple of years ago. Remove it from the
list of known issues.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The original code was based on my reverse engineering of an I2C trace
of the Windows driver. Now that I know what the registers actually do,
restructure the code a bit, removing some unneeded register programming
and fixing the sequencing of operations.
This reduces the time it takes to change inputs from 1300ms down to
600ms (as measured by "time v4l2-ctl -i 0")
Note this does not address outstanding issues related to the management
of the module clocks and power control for the various blocks, which
will be done in a separate patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some stray lines got inserted into the driver when I reverse engineered
the I2C traffic (at the time I didn't know what the registers did).
It turns up these registers muck with the onboard I2C master, which
we don't use since we instead use the I2C gate. Remove the lines
which can actually interfere with the operation of the bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since we don't suppoort sliced VBI with the au0828/au8522, there is
no need to configure the au8522 VBI slicer, which because of the
coefficients requires a large amount of i2c traffic.
Remove the relevant code. Note that this has no effect on raw VBI
support, which is currently the only supported way to access VBI on
this device.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
As we want au0828 to use the core function to create the MC
graphs, use enum demod_pad_index instead of
enum au8522_media_pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new pad for ALSA Audio Out to au8522_media_pads.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for analog and dvb tv using media controller.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kmemleak:
unreferenced object 0xffff880321e1da40 (size 32):
comm "modprobe", pid 3309, jiffies 4295019569 (age 2359.636s)
hex dump (first 32 bytes):
47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G...............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff82278c8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8153c08c>] kmem_cache_alloc_trace+0x1ec/0x280
[<ffffffffa13a896a>] au8522_probe+0x19a/0xa30 [au8522_decoder]
[<ffffffff81de0032>] i2c_device_probe+0x2b2/0x490
[<ffffffff81ca7004>] driver_probe_device+0x454/0xd90
[<ffffffff81ca7c1b>] __device_attach_driver+0x17b/0x230
[<ffffffff81ca15da>] bus_for_each_drv+0x11a/0x1b0
[<ffffffff81ca6a4d>] __device_attach+0x1cd/0x2c0
[<ffffffff81ca7d43>] device_initial_probe+0x13/0x20
[<ffffffff81ca451f>] bus_probe_device+0x1af/0x250
[<ffffffff81c9e0f3>] device_add+0x943/0x13b0
[<ffffffff81c9eb7a>] device_register+0x1a/0x20
[<ffffffff81de8626>] i2c_new_device+0x5d6/0x8f0
[<ffffffffa0d88ea4>] v4l2_i2c_new_subdev_board+0x1e4/0x250 [v4l2_common]
[<ffffffffa0d88fe7>] v4l2_i2c_new_subdev+0xd7/0x110 [v4l2_common]
[<ffffffffa13b2f76>] au0828_card_analog_fe_setup+0x2e6/0x3f0 [au0828]
Checking where the error happens:
(gdb) list *au8522_probe+0x19a
0x99a is in au8522_probe (drivers/media/dvb-frontends/au8522_decoder.c:761).
756 printk(KERN_INFO "au8522_decoder attach existing instance.\n");
757 break;
758 }
759
760 demod_config = kzalloc(sizeof(struct au8522_config), GFP_KERNEL);
761 if (demod_config == NULL) {
762 if (instance == 1)
763 kfree(state);
764 return -ENOMEM;
765 }
Shows that the error path is not being handled properly.
The are actually several issues here:
1) config free should have been calling hybrid_tuner_release_state()
function, by calling au8522_release_state();
2) config is only allocated at the digital part. On the analog one,
it is received from the caller.
A complex logic could be added to address it, however, it is simpler
to just embeed config inside the state.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several issues on the current code:
1) msleep(1) is actually equivalent to msleep(10);
2) au8522_video_set() will set reg 0xa4 to the
proper value for SIF, CVBS or S-Video. No need
to force it to CVBS;
3) Let's not hardcode 0x9d for CBS on audio_set.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.
As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.
So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that au0828 has been converted to the control framework these
compatilibity ops are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-08-13 23:13:41 -03:00
Renamed from drivers/media/dvb/frontends/au8522_decoder.c (Browse further)
