Add a tsspeed config option to struct stv0910_cfg which can be used by
users of the driver to set the (parallel) TS speed (higher speeds enable
support for higher bitrate transponders). If tsspeed isn't set in the
config, it'll default to a sane value.
This commit also updates the two consumers of the stv0910 driver (ngene
and ddbridge) to have a default tsspeed in their stv0910_cfg templates.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Helmut Auer <post@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The method dvb_frontend_ops::get_frontend_algo() is defined as
returning an 'enum dvbfe_algo', but the implementation in this
driver returns an 'int'.
Fix this by returning 'enum dvbfe_algo' on drivers.
[mchehab+samsung@kernel.org: merge similar patches and patch
ddbridge-mci.c the same way]
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CNR value determined in read_snr() is reported via the wrong variable.
It uses FE_SCALE_DECIBEL, which implies the value to be reported in svalue
instead of uvalue. Fix this accordingly.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The TSINSDEL registers were lacking initialisation in the stv0910 demod
driver. Initialise them (both demods) in the probe() function.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework both DiSEqC send functions (send_master_cmd() and send_burst()) to
utilise the new SET_REG() and SET_FIELD() macros. Esp. due to SET_FIELD(),
this makes sure that not all bits (with unrelated purposes) are always
rewritten, but only those needed for sending DiSEqC commands. In
send_burst(), this makes sure that DISEQC_MODE isn't changed from 3 to 2
inbetween when sending SEC_MINI_A. Also, change both functions to write
DISEQC_MODE first before setting DIS_PRECHARGE. This makes diseqc control
work more reliable for "fullblown" DiSEqC strings in VDR's diseqc.conf in
combination with certain multiswitches.
Fixes: 448461af0e ("media: dvb-frontends/stv0910: implement diseqc_send_burst")
Reported-by: Helmut Auer <post@helmutauer.de>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Helmut Auer <post@helmutauer.de>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleanup the mess in init_search_param() by utilising the new register
access macros and functions. And while at it, move the ISI and PLS setup
into separate functions, and pass the new scrambling_sequence_index (aka.
physical layer scrambling) value to set_pls.
Picked up from the dddvb upstream, adapted to the different naming of the
pls property (pls vs. scrambling_sequence_index).
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a write_field() function that acts as helper to update specific bits
specified in the field defines (FSTV0910_*) in stv0910_regs.h, which was
recently updated to carry the missing offset values. With that, add the
SET_FIELD(), SET_REG() and GET_REG() macros that wrap the write_field(),
write_reg() and read_reg() functions to allow for making all demod
access code cleaner.
The write_field() function is annotated with __maybe_unused temporarily
to silence eventual compile warnings.
Picked up from the dddvb upstream, with the macro names made uppercase
so they are distinguishable as such.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
write_reg() and i2c_write_reg16() only act as a proxy to i2c_write(), which
isn't called from anywhere else throughout the driver. Clean this up by
moving the message setup and the i2c_transfer() into write_reg() so it
becomes the only I2C write function. While touching those parts, fix the
error codes from EREMOTEIO to EIO.
The I2C cleanup is picked from the upstream dddvb.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For all code rates, the same write is performed, only with a differing
value. Clean this up by putting that value into a variable instead and
perform the write at the end with that value.
Picked up from the dddvb upstream.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since nothing from dvb_math.h is used, remove the unneeded include.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tracking_optimization() doesn't make use of the symbol rate reported by
the demodulator, so remove the unneeded inquiry and the now unneeded
variable.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Utilise get_cur_symbol_rate() in get_frontend() to update the
dtv_frontend_properties with the current symbol rate as reported by the
demodulator.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The result (if any) isn't used anywhere besides being assigned to a local
variable (and the only current companion stv6111 doesn't even implement
get_if_frequency()), thus remove the ptr check and the call, and also
remove the now unused iffreq variable.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stack dump when gate_ctrl() is called in a way that consecutive unlocks
happen. This is a clear indication that other drivers interfacing with
the stv0910 driver don't do things properly or don't check for failures,
so dump stack so that those drivers can be identified and fixed.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add missing state->modcod update from upstream driver which needs to be
done when manage_matype_info() sets is_vcm on certain S2 transponders.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The demodulator supports symbol rates as low as 100Ksyms/s - the demod
setup in start() already handles such low symbol rates and reviewers
of stv0910 equipped cards even found and tested transponders with
SRs in that range. So, announce this in the fe_ops.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whenever write_reg() fails to open/close the demod's I2C gate, release the
lock to avoid deadlocking situations. If I2c gate open failed, there's no
need to hold a lock, and if close fails, the mutex_unlock() at the end of
the function is never reached, leaving the mutex_lock in locked state,
which in turn will cause potential for deadlocks. Thus, release the lock
on failure.
While we're touching gate_ctrl(), add some explanation about the need for
locking and the shared I2C bus/gate.
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleans up smatch warning:
symbol 'stvlist' was not declared. Should it be static?
Patch originally submitted by Colin Ian King <colin.king@canonical.com>,
remainder after the merge of all other stv0910 fixes.
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The scrambling code has 4 bits. Fix the mask accordingly.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It should first read the status and then check if FE has lock.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mark lookup tables and fe_ops things const so the compiler can put them
into .rodata.
While at it, improve name and identifier strings (moddesc, fe_ops).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix up block comment style, whitespaces, c++ style comments et al.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes up all remainders reported by "checkpatch.pl --strict"
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements the diseqc_send_burst frontend op to support sending
mini-DISEQC bursts. Picked up from dddvb's driver package where this
specific block was disabled via #if 0/#endif, but is still working
according to feedback from upstream, so add it.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the documentation, FE_SCALE_DECIBEL values should be assigned
to .svalue and not .uvalue, so let's do this. While at it, remove the
unneeded strength var from read_signal_strength().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This was missing from the frontend_ops.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Original code at least has some signed/unsigned issues, resulting in
values like 32dBm. Implement signal strength readout to work without
asking the attached tuner, and use a lookup table instead of log calc.
Values reported appear plausible, gathered from feedback from several
testers.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements stream_id filter and scrambling code setup in start() and also
sets FE_CAN_MULTISTREAM in frontend_ops. This enables the driver to
properly receive and handle multistream transponders, functionality has
been reported working fine by testers with access to such streams, in
conjunction with VDR on the userspace side.
The code snippet originates from the original vendor's dddvb driver
package and has been made working properly with the current in-kernel
DVB core API.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes smatch error:
drivers/media/dvb-frontends/stv0910.c:715 dvbs2_nbch() error: buffer overflow 'nbch[fectype]' 2 <= 28
Also, fixes the nbch array table by adding the DUMMY_PLF element at the top
to match the enums (table element order was off by one before).
Patch sent upstream aswell.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator
frontends. The driver code originates from the Digital Devices' dddvb
vendor driver package as of version 0.9.29, and has been cleaned up from
core API usage which isn't supported yet in the kernel, and additionally
all obvious style issues have been resolved. All camel case and allcaps
have been converted to kernel_case and lowercase. Patches have been sent
to the vendor package maintainers to fix this aswell. Signal statistics
acquisition has been refactored to comply with standards.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>