Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a suffix to distinguish kernel mainline version and aquantia releases
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On very first start we should read out current HW counter values
to make diff based calculations later.
This also should be done each time NIC gets down/up or wakes up
after sleep state. We reset link state explicitly to prevent diffs
from being summed this first time.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce timeout from 2 secs to 1 sec. If link is down,
reduce it to 500msec. This speeds up link detection.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This metric comes from HW and is also diff-calculated, like other counters
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally they were filled from ring sw counters.
These sometimes incorrectly calculate byte and packet amounts
when using LRO/LSO and jumboframes. Filling ndev counters from
hardware makes them precise.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device hardware provides only 32bit counters. Using these directly
causes byte counters to overflow soon. A separate nic level structure
with 64 bit counters is now used to collect incrementally all the stats
and report these counters to ethtool stats and ndev stats.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.
Fixes: 2b94e58df5 ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, the stats_lock was acquired twice. In between the
locks Driver sent command to gather some more statistics (per priority
and counter statistics). If the stats lock was acquired by get
statistics NDO in between we would have report out of sync counters.
Fix this by collecting all stats from Firmware in advance and then
fill the Software structs under one lock.
Fixes: 0b131561a7 ("net/mlx4_en: Add Flow control statistics display via ethtool")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field res_free indicates the total number of counters which are
available for allocation (reserved and unreserved). Fixed a bug where
the reserved counters were subtracted from res_free before any
allocation was performed.
Before this fix, free counters which were not reserved could not be
allocated.
Fixes: 9de92c60be ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the minimal MTU threshold for running loopback selftest.
MTU should be big enough to include packet payload, NET_IP_ALIGN,
Ethernet headers and preamble length.
Fixes: e7c1c2c462 ("mlx4_en: Added self diagnostics test implementation")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in SGMII-to-Copper mode, the fiber page is used for the MAC facing
link, and does not require configuration of the fiber auto-negotiation
settings. Avoid trying.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meson_gxl_read_status is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'meson_gxl_read_status' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.
The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit. This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.
Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock. This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMII is a 32-bit bus plus two clock signals per direction. XAUI is
four serial lanes per direction. The 88e6190 supports XAUI but not
XGMII as it doesn't have enough pins. The same is true of 88e6176.
Match on PHY_INTERFACE_MODE_XAUI for the XAUI port type, but keep
accepting XGMII for backwards compatibility.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a spinlock.
The function call path is:
rr_close (acquire the spinlock)
free_irq --> may sleep
To fix it, free_irq is moved to the place without holding the spinlock.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Changes since v2 [1]:
* Merged with latest code changes
Changes since v1:
Update made thanks to David's review, much appreciated David.
* Improved inconsistent failure handling of clock rate setting
* For completeness of usecase, added arc_emac_probe error handling
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fbf3d034f2.
As of commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
Fixes: 7334b3e47a ("net: phy: Add Meson GXL Internal PHY driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
A couple of minor bugfixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaKW26AAoJECgfDbjSjVRpDwIH/1tq1vcjd5i00nh+gQD7jWm2
qWrpcKbsS0ANTvhm9UNFY24BVoPuNpNrApQpuBxmgxE/XGqx7A+8xXhwPAM5lLiG
uDSPB2nsfjvEUOde7bgeR+t6ay+Ki2UWKzY46lSoCTcIN7BSVFWQZonsGu2xLDzz
kKpCtlobXRnXzeWm+fh1oOZu/cn/TuAF0mbb+6TUQqSsHAt6PQ3Hwsly2EmQV5xR
of6Si/TnxFOkhZUKpezbuTU/g/20ZkHUSzgfrOuZLGonaIvZIE6BUm8m21/IgCbw
WnwSqe66WsWF2vd0RDLFq4L3qaRyGn+W7iYo3KPbwIPEEotSRFMUgixBWBB3IgU=
=Pf4w
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAloqeVYTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9tiqCADK4f/QYW5q5jC93A6JZSItI8vAK2+h
0s4MRTj9x+thBIGIhJ59uYBSTd374bvsWmrGdV7CBoGX4TnEJfGiMV77lpGnGRVG
jpzk9cSFoAnE5UW2qZlF+JM8SNEFlU18MCQQlnMzKbSGerUAlveK+mcF5sJrqrQh
CGZ9MH1Bp4Fz3WMRQ9hHzKWjTOhhM54qjPceCVTZM6I0RJam6I2lpVZPQeom9uVa
r+F5Lv2ZOpNZc+8Pbu+L95YyivKKaQOPzeP4btFLNEHUyFDygHcv2iKRIn9MdEu2
2XfaDVKk2Ey/qWc782SLBxLOihnhWltwC7Kg1ZnrLhNZ6V5UbYQ5FzF4
=OMZE
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.15-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-08
this is a pull request of 6 patches for net/master.
Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaKp9UAAoJEG4XJFUm622bhXgH+wTtTVEH0lAOTtK+PyBkxkRH
Q+55Yf1XZ9lNYxmfXhYgObusSbmeL8tClMuISCcQS9gX0um1Vuuud4CLemgO2V7R
V1xuWTKjanaKf8PouKx9SUt1Fx6CsFdwlivJX+eZTfKlKYtwNbNX4onWl9GN2jVZ
5/2l+m3MJbTMMzarZTGLkBJqpTk8DGTNINtKeRd+VF+717SlbqpRlw1TTlbVJcR2
nHcJ3p5JGbU/+hOTroOWUr7kGdpdYlWLfcyOL8iT3rZXtAzH/POjPAmQv9VVRaC+
anm5zn+gZ5GH9XF+pc3nrGOEZ2Ei4LtszMQjdo4Zo9V3ngCj/0OoEnkto6VLbkw=
=lzG8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.
Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function virtqueue_get_buf_ctx() could return NULL, the return
value 'buf' need to be checked with NULL, not value 'ctx'.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
-----BEGIN PGP SIGNATURE-----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=VSq5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi patches intended for 4.15.
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed
Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
