Use CLAIM tags to make sure the device is available for use.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we honor the errors in CATU device and abort the operation.
While at it, delay setting the etr_buf for the session until we are
sure that we are indeed enabling the ETR.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the tmc-etr enable operation to make it easier to
handle errors in enabling the hardware. We need to make
sure that the buffer is compatible with the ETR. This
patch re-arranges to make the error handling easier, by
deferring the hardware enablement until all the errors
are checked. This also avoids turning the CATU on/off
during a sysfs read session.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using TMC-ETR as backend for ETM perf tracing.
We use software double buffering at the moment. i.e, the TMC-ETR
uses a separate buffer than the perf ring buffer. The data is
copied to the perf ring buffer once a session completes.
The TMC-ETR would try to match the larger of perf ring buffer
or the ETR buffer size configured via sysfs, scaling down to
a minimum limit of 1MB.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In coresight perf mode, we need to prepare the sink before
starting a session, which is done via set_buffer call back.
We then proceed to enable the tracing. If we fail to start
the session successfully, we leave the sink configuration
unchanged. In order to make the operation atomic and to
avoid yet another call back to clear the buffer, we get
rid of the "set_buffer" call back and pass the buffer details
via enable() call back to the sink.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert component enable/disable messages from dev_info to dev_dbg.
When used with perf, the components in the paths are enabled/disabled
during each schedule of the run, which can flood the dmesg with these
messages. Moreover, they are only useful for debug purposes. So,
convert such messages to dev_dbg() which can be turned on as
needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ETR now uses mode specific buffers, we can reliably
provide the trace data captured in sysfs mode, even when the ETR
is operating in PERF mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ETR could be driven either by SYSFS or by perf, it
becomes complicated how we deal with the buffers used for each
of these modes. The ETR driver cannot simply free the current
attached buffer without knowing the provider (i.e, sysfs vs perf).
To solve this issue, we provide:
1) the driver-mode specific etr buffer to be retained in the drvdata
2) the etr_buf for a session should be passed on when enabling the
hardware, which will be stored in drvdata->etr_buf. This will be
replaced (not free'd) as soon as the hardware is disabled, after
necessary sync operation.
The advantages of this are :
1) The common code path doesn't need to worry about how to dispose
an existing buffer, if it is about to start a new session with a
different buffer, possibly in a different mode.
2) The driver mode can control its buffers and can get access to the
saved session even when the hardware is operating in a different
mode. (e.g, we can still access a trace buffer from a sysfs mode
even if the etr is now used in perf mode, without disrupting the
current session.)
Towards this, we introduce a sysfs specific data which will hold the
etr_buf used for sysfs mode of operation, controlled solely by the
sysfs mode handling code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ERR_CAT inlined function to replace the ERR_PTR(PTR_ERR). It
make the code more concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can use a CATU with a scatter gather table, add support
for the TMC ETR to make use of the connected CATU in translate mode.
This is done by adding CATU as new buffer mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the initial support for Coresight Address Translation Unit, which
augments the TMC in Coresight SoC-600 by providing an improved Scatter
Gather mechanism. CATU is always connected to a single TMC-ETR and
converts the AXI address with a translated address (from a given SG
table with specific format). The CATU should be programmed in pass
through mode and enabled even if the ETR doesn't use the translation
by CATU.
This patch provides mechanism to enable/disable the CATU always in the
pass through mode.
We reuse the existing ports mechanism to link the TMC-ETR to the
connected CATU.
i.e, TMC-ETR:output_port0 -> CATU:input_port0
Reference manual for CATU component is avilable in version r2p0 of :
"Arm Coresight System-on-Chip SoC-600 Technical Reference Manual".
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We request for "CORESIGHT_BARRIER_PKT_SIZE" length and we should
be happy when we get that size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly introduced code fails to build in some configurations
unless we include the right headers:
drivers/hwtracing/coresight/coresight-tmc-etr.c: In function 'tmc_free_table_pages':
drivers/hwtracing/coresight/coresight-tmc-etr.c:206:3: error: implicit declaration of function 'vunmap'; did you mean 'iounmap'? [-Werror=implicit-function-declaration]
Fixes: 79613ae8715a ("coresight: Add generic TMC sg table framework")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support for Scatter-Gather mode to the etr-buf layer.
Since we now have two different modes, we choose the backend
based on a set of conditions, documented in the code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC-ETR can use the target trace buffer in two different modes.
Normal physically contiguous mode and a discontiguous list pages in
Scatter-Gather mode. Also we have dedicated Coresight component, CATU
(Coresight Address Translation Unit) to provide improved scatter-gather
mode in Coresight SoC-600. This complicates the management of the
buffer used for trace, depending on the mode in which ETR is configured.
So, this patch adds a transparent layer for managing the ETR buffer
which abstracts the basic operations on the buffer (alloc, free,
sync and retrieve the data) and uses the mode specific helpers to
do the actual operation. This also allows the ETR driver to choose
the best mode for a given use case and adds the flexibility to
fallback to a different mode, without duplicating the code.
The patch also adds the "normal" flat memory mode and switches
the sysfs driver to use the new layer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for setting up an SG table used by the
TMC ETR inbuilt SG unit. The TMC ETR uses 4K page sized tables
to hold pointers to the 4K data pages with the last entry in a
table pointing to the next table with the entries, by kind of
chaining. The 2 LSBs determine the type of the table entry, to
one of :
Normal - Points to a 4KB data page.
Last - Points to a 4KB data page, but is the last entry in the
page table.
Link - Points to another 4KB table page with pointers to data.
The code takes care of handling the system page size which could
be different than 4K. So we could end up putting multiple ETR
SG tables in a single system page, vice versa for the data pages.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we open code filling the trace buffer with synchronization
packets when the circular buffer wraps around in different drivers.
Move this to a common place. While at it, clean up the barrier_pkt
array to strip off the trailing '\0'.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't support ETR in perf mode yet. So, don't
even try to enable the hardware, even by mistake.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We zero out the entire trace buffer used for ETR before it is enabled,
for helping with debugging. With the addition of scatter-gather mode,
the buffer could be bigger and non-contiguous.
Get rid of this step; if someone wants to debug, they can always add it
as and when needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker. As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either. Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight SoC 600 TMC ETR supports save-restore feature,
where the values of the RRP/RWP and STS.Full are retained
when it leaves the Disabled state. Hence, we must program the
RRP/RWP and STS.Full to a proper value. For now, set the RRP/RWP
to the base address of the buffer and clear the STS.Full register.
This can be later exploited for proper save-restore of ETR
trace contexts (e.g, perf).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETR supports split cache encoding (i.e, separate bits for
read and write transfers) unlike the older version (where read
and write transfers use the same encoding in AXICTL[2-5]).
This feature is not advertised and has to be described by the
static mask associated with the device id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up how we setup the AXICTL register on
TMC ETR. At the moment we don't set the CacheCtrl bits, which
drives the arcache and awcache bits on AXI bus specifying the
cacheablitiy. Set this to Write-back Read and Write-allocate.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight TMC splits 64bit registers into a pair of 32bit registers
(e.g DBA, RRP, RWP). Provide helpers to read/write to these registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer overflow happens the synchronisation patckets usually
present at the beginning of the buffer are lost, a situation that
prevents the decoder from knowing the context of the traces being
decoded.
This patch adds a barrier packet to be used by sink IPs when a buffer
overflow condition is detected. These barrier packets are then used
by the decoding library as markers to force re-synchronisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmc_etr_enable_hw() fills the buffer with 0's before enabling
the hardware. So, we don't need an explicit memset() in
tmc_enable_etr_sink_sysfs() before calling the tmc_etr_enable_hw().
This patch removes the explicit memset from tmc_enable_etr_sink_sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of the superfluous mode parameter and the check for
the mode in tmc_etX_enable_sink_{perf/sysfs}. While at it, also
remove the unnecessary WARN_ON() checks.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode of operation of the TMC tracked in drvdata->mode is defined
as a local_t type. This is always checked and modified under the
drvdata->spinlock and hence we don't need local_t for it and the
unnecessary synchronisation instructions that comes with it. This
change makes the code a bit more cleaner.
Also fixes the order in which we update the drvdata->mode to
CS_MODE_DISABLED. i.e, in tmc_disable_etX_sink we change the
mode to CS_MODE_DISABLED before invoking tmc_disable_etX_hw()
which in turn depends on the mode to decide whether to dump the
trace to a buffer.
Applies on mathieu's coresight/next tree [1]
https://git.linaro.org/kernel/coresight.git next
Reported-by: Venkatesh Vivekanandan <venkatesh.vivekanandan@broadcom.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get a few warnings when building kernel with W=1:
drivers/hwtracing/coresight/coresight-tmc-etr.c:23:6: warning: no previous prototype for 'tmc_etr_enable_hw' [-Wmissing-prototypes]
drivers/hwtracing/coresight/coresight-tmc-etf.c:25:6: warning: no previous prototype for 'tmc_etb_enable_hw' [-Wmissing-prototypes]
drivers/hwtracing/coresight/coresight-tmc.c:250:9: warning: no previous prototype for ‘trigger_cntr_show’ [-Wmissing-prototypes]
...
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the defined symbol rather than hardcoding the value to
check whether the TMC buffer is full.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present the ETF or ETR gives out the entire device
buffer, even if there is less or even no trace data
available. This patch limits the trace data given out to
the actual trace data collected.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of a trace collection, we try to clear the entire buffer
and enable the ETR back if it was already enabled. But, we would have
adjusted the drvdata->buf to point to the beginning of the trace data
in the trace buffer @drvdata->vaddr. So, the following code which
clears the buffer is dangerous and can cause crashes, like below :
memset(drvdata->buf, 0, drvdata->size);
Unable to handle kernel paging request at virtual address ffffff800a145000
pgd = ffffffc974726000
*pgd=00000009f3e91003, *pud=00000009f3e91003, *pmd=0000000000000000
PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1692 Comm: dd Not tainted 4.7.0-rc2+ #1721
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9734a0080 ti: ffffffc974460000 task.ti: ffffffc974460000
PC is at __memset+0x1ac/0x200
LR is at tmc_read_unprepare_etr+0x144/0x1bc
pc : [<ffffff80083a05ac>] lr : [<ffffff800859c984>] pstate: 200001c5
...
[<ffffff80083a05ac>] __memset+0x1ac/0x200
[<ffffff800859b2e4>] tmc_release+0x90/0x94
[<ffffff8008202f58>] __fput+0xa8/0x1ec
[<ffffff80082030f4>] ____fput+0xc/0x14
[<ffffff80080c3ef8>] task_work_run+0xb0/0xe4
[<ffffff8008088bf4>] do_notify_resume+0x64/0x6c
[<ffffff8008084d5c>] work_pending+0x10/0x14
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
Since we clear the buffer anyway in the following call to
tmc_etr_enable_hw(), remove the erroneous memset().
Fixes: commit de5461970b ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of the trace capture, we free the allocated memory,
resetting the drvdata->buf to NULL, to indicate that trace data
was collected and the next trace session should allocate the
memory in tmc_enable_etr_sink_sysfs.
The tmc_enable_etr_sink_sysfs, we only allocate memory if drvdata->vaddr
is not NULL (which is not performed at the end of previous session).
This can cause, drvdata->vaddr getting assigned NULL and later we do
memset() which causes a crash as below :
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
pgd = ffffffc9747f0000
[00000000] *pgd=00000009f402e003, *pud=00000009f402e003,
*pmd=0000000000000000
Internal error: Oops: 96000046 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1592 Comm: bash Not tainted 4.7.0-rc1+ #1712
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc078fe0080 ti: ffffffc974178000 task.ti: ffffffc974178000
PC is at __memset+0x1ac/0x200
LR is at tmc_enable_etr_sink+0xf8/0x304
pc : [<ffffff80083a002c>] lr : [<ffffff800859be44>] pstate: 400001c5
sp : ffffffc97417bc00
x29: ffffffc97417bc00 x28: ffffffc974178000
Call trace:
Exception stack(0xffffffc97417ba40 to 0xffffffc97417bb60)
ba40: 0000000000000001 ffffffc974a5d098 ffffffc97417bc00 ffffff80083a002c
ba60: ffffffc974a5d118 0000000000000000 0000000000000000 0000000000000000
ba80: 0000000000000001 0000000000000000 ffffff800859bdec 0000000000000040
baa0: ffffff8008b45b58 00000000000001c0 ffffffc97417baf0 ffffff80080eddb4
bac0: 0000000000000003 ffffffc078fe0080 ffffffc078fe0960 ffffffc078fe0940
bae0: 0000000000000000 0000000000000000 00000000007fffc0 0000000000000004
bb00: 0000000000000000 0000000000000040 000000000000003f 0000000000000000
bb20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
bb40: ffffffc078fe0960 0000000000000018 ffffffffffffffff 0008669628000000
[<ffffff80083a002c>] __memset+0x1ac/0x200
[<ffffff8008599814>] coresight_enable_path+0xa8/0x1dc
[<ffffff8008599b10>] coresight_enable+0x88/0x1b8
[<ffffff8008599d88>] enable_source_store+0x3c/0x6c
[<ffffff800845eaf4>] dev_attr_store+0x18/0x28
[<ffffff80082829e8>] sysfs_kf_write+0x54/0x64
[<ffffff8008281c30>] kernfs_fop_write+0x148/0x1d8
[<ffffff8008200128>] __vfs_write+0x28/0x110
[<ffffff8008200e88>] vfs_write+0xa0/0x198
[<ffffff80082021b0>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
This patch fixes the issue by clearing the drvdata->vaddr while we free
the allocated buffer at the end of a session, so that we allocate the
memory again.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysFS and Perf access methods can't be allowed to interfere
with one another. As such introducing guards to access
functions that prevents moving forward if a TMC is already
being used.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling tmc_etf/etr_dump_hw() is required only when operating from
sysFS. When working from Perf, the system memory is harvested
from the AUX trace API.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving tmc_drvdata::enable to a local_t mode. That way the
sink interface is aware of it's orgin and the foundation for
mutual exclusion between the sysFS and Perf interface can be
laid out.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allowing multiple readers to access the trace data simultaniously
via sysFS provides no shortage of opportunity for race condition,
mandates two variable to be maintained (drvdata::read_count and
drvdata::reading), makes the code complex and provide little
advantages, if any.
This patch streamlines the read process by restricting trace data
access to a single user. That way drvdata::read_count can
be eliminated and race conditions (along with faulty error handling)
in function tmc_open() and tmc_release() eliminated.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In it's current form the TMC probe() function allocates
trace buffer memory at boot time, event if coresight isn't
used. This is highly inefficient since trace buffers can
occupy a lot of memory that could be used otherwised.
This patch allocates trace buffers on the fly, when the
coresight subsystem is solicited. Allocated buffers are
released when traces are read using the device descriptors
under /dev.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dealing with HW related matters in tmc_read_prepare/unprepare
becomes convoluted when many cases need to be handled distinctively.
As such moving processing related to HW setup to individual driver
files and keep the core driver generic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC block can operate in 3 modes (ETB, ETF and ETR) and accessed
via two interfaces (sysFS and Perf). That makes 6 mode to cover, which
is way too much coupling for a single file.
This patch splits the original TMC driver in 2 halves, one for ETB/ETF
and another one for ETR mode. A common core is kept for functionality
common to all 3 modes.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose