Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
If an error occurs mid way through a transaction (such as a missing CRC
status response after the 2nd block written out of 3), then the FIFO may
still contain data which will interfere with the next transaction.
Therefore after an error has been detected, reset the fifo using the
CTRL register.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a data write isn't acknowledged by the card (so no CRC status token
is detected after the data), the error -EIO is returned instead of the
-ETIMEDOUT expected by mmc_test 15 - "Correct xfer_size at write (start
failure)" and 17 "Correct xfer_size at write (midway failure)". In PIO
mode the reported number of bytes transferred is also exaggerated since
the last block actually failed.
Handle the "Write no CRC" error specially, setting the error to
-ETIMEDOUT and setting the bytes_xferred to 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove error messages for timeout and CRC failure, since the error code
already indicates the problem.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.
Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.
Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.
Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.
Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a request is made, the card presence is checked and the request is
queued. These two parts must be atomic with respect to card removal, or
a card removal could be handled in between, and the new request wouldn't
get cancelled until another card was inserted. Therefore move the
spinlock protection from dw_mci_queue_request() up into dw_mci_request()
to cover the presence check.
Note that the test_bit() used for the presence check isn't atomic
itself, so should have been protected by a spinlock anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
DMA is only used for transactions exceeding a certain length, otherwise
PIO is used. The TXDR and RXDR interrupts are masked when in DMA mode
but still fire. When switching to PIO mode (e.g. to get SCR field when
an SD card is inserted) these interrupts are not cleared and so they
trigger the ISR as soon as they are unmasked. If the previous DMA did a
write, then the ISR will handle the TXDR interrupt even if the
transaction is a read, completing the transaction without modifying the
read buffer.
This is fixed primarily by clearing these two interrupts before
unmasking them when setting up PIO mode, and also by making the ISR more
robust by only handling TXDR/RXDR in the correct read/write direction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Response timeout (RTO), Response crc error (RCRC) and Response error (RE)
signals come with command done (CD) and can be raised preceding command
done (CD). That is these error interrupts and CD can be handled in
separate dw_mci_interrupt(). If mmc_request_done() is called because of
a response timeout before command done has occured, we might send the
next request before the CD of current request is finished. This can
bring about a broken sequence of request and request-done.
And Data error interrupt (DRTO, DCRC, SBE, EBE) and data transfer
over (DTO) have the same problem.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch sets the card_width bit of CTYPE for the corresponding card.
CTYPE[31] and CTYPE[16] correspond respectively to card[15] and card[0]
for 8-bit mode. And CTYPE[15] and CTYPE[0] correspond respectively to
card[15] and CTYPE[0] for 1-bit or 4-bit mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
regulator_enable() was incorrectly placed in the suspend function
instead of the resume function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for power regulators.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is related to re-init processing on suspend/resume.
When card is resuming, some register is reset. If card is removable,
maybe controller should be rescan for card. But if assume card is
non-removable, need to restore the old value at registers.
We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds quirks and capabilities to platdata.
Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all. So, both are redundant. Fixes:
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Will Newton <will.newton@imgtec.com>
This patch adds DDR mode support to dw_mmc.
If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode. For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting this bit in the clock enable register will stop the clock
when the card is in the IDLE state.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to run the card detect tasklet at the end of slot initialisation
as it is possible that a card has been inserted prior to boot, so we don't
see an insertion interrupt and now the card is sitting there inserted but
with no power to it.
Signed-off-by: Neil Jones <neil.jones@imgtec.com>
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the mmc host driver for the Synopsys DesignWare mmc
host controller, found in a number of embedded SoC designs.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
