This patch fixes two lines in which the rx_offset received by the device
wasn't taken into account:
- prefetch function:
In our driver the copied data would reside in
rx_info->page + rx_headroom + rx_offset
so the prefetch function is changed accordingly.
- setting page_offset to zero for descriptors > 1:
for every descriptor but the first, the rx_offset is zero. Hence
the page_offset value should be set to rx_headroom.
The previous implementation changed the value of rx_info after
the descriptor was added to the SKB (essentially providing wrong
page offset).
Fixes: 68f236df93 ("net: ena: add support for the rx offset feature")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.
If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.
This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.
DMA mask is set again to the correct value after it's received from the
device after readless is initialized.
The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After request id is checked in validate_rx_req_id() its value is still
used in the line
rx_ring->free_ids[next_to_clean] =
rx_ring->ena_bufs[i].req_id;
even if it was found to be out-of-bound for the array free_ids.
The patch moves the request id to an earlier stage in the napi routine and
makes sure its value isn't used if it's found out-of-bounds.
Fixes: 30623e1ed1 ("net: ena: avoid memory access violation by validating req_id properly")
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After running Sparse checker on the driver using
make C=1 M=drivers/net/ethernet/amazon/ena
the only error that is thrown is:
sparse: sparse: Using plain integer as NULL pointer
about the line
struct ena_calc_queue_size_ctx calc_queue_ctx = { 0 };
This patch fixes this warning, thus making our driver free (for now) of
Sparse errors/warnings.
To make a more complete work, this patch also fixes all static warnings
that were found using an internal static checker.
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The placement policy is printed in the process of queue creation in
ena_up(). No need to print it in ena_probe().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Capitalize all log strings printed by the ena driver to make their
format uniform across it.
Also fix indentation, spelling mistakes and comments to improve code
readability. This also includes adding comments to macros/enums whose
purpose might be difficult to understand.
Separate some code into functions to make it easier to understand the
purpose of these lines.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make log prints in ena_netdev use the same log functions as the rest of
the driver.
For the sake of consistency, all prints in ena_netdev file were
converted into netif_* format except where netdev struct isn't yet
defined. For these places, dev_* log functions are used (similar to
the patch for ena_com files).
This commit leaves some corner cases which would be changed in a
future patch.
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ena files should now use SPDX format in their license string. This
doesn't change the license of the files, but rather states the same
license in fewer words.
Also update the license years in some of the files.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using XDP every ingress packet is passed to an eBPF (xdp) program
which returns an action for this packet.
This patch adds counters for the number of times each such action was
received. It also counts all the invalid actions received from the eBPF
program.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new metrics provide granular visibility along multiple network
dimensions and enable troubleshooting and remediation of issues caused
by instances exceeding network performance allowances.
The new statistics can be queried using ethtool command.
Signed-off-by: Guy Tzalik <gtzalik@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb71 ("net: ena: add statistics for missed tx packets")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena_del_napi_in_range() function unregisters the napi handler for
rings in a given range.
This function had the following WARN_ON macro:
WARN_ON(ENA_IS_XDP_INDEX(adapter, i) &&
adapter->ena_napi[i].xdp_ring);
This macro prints the call stack if the expression inside of it is
true [1], but the expression inside of it is the wanted situation.
The expression checks whether the ring has an XDP queue and its index
corresponds to a XDP one.
This patch changes the expression to
!ENA_IS_XDP_INDEX(adapter, i) && adapter->ena_napi[i].xdp_ring
which indicates an unwanted situation.
Also, change the structure of the function. The napi handler is
unregistered for all rings, and so there's no need to check whether the
index is an XDP index or not. By removing this check the code becomes
much more readable.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset work is scheduled by the timer routine whenever it
detects that a device reset is required (e.g. when a keep_alive signal
is missing).
When releasing device resources in ena_destroy_device() the driver
cancels the scheduling of the timer routine without destroying the reset
work explicitly.
This creates the following bug:
The driver is suspended and the ena_suspend() function is called
-> This function calls ena_destroy_device() to free the net device
resources
-> The driver waits for the timer routine to finish
its execution and then cancels it, thus preventing from it
to be called again.
If, in its final execution, the timer routine schedules a reset,
the reset routine might be called afterwards,and a redundant call to
ena_restore_device() would be made.
By changing the reset routine we allow it to read the device's state
accurately.
This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set
before resetting the device and making both the destruction function and
the flag check are under rtnl lock.
The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction
routine. Also surround the flag check with 'likely' because
we expect that the reset routine would be called only when
ENA_FLAG_TRIGGER_RESET flag is set.
The destruction of the timer and reset services in __ena_shutoff() have to
stay, even though the timer routine is destroyed in ena_destroy_device().
This is to avoid a case in which the reset routine is scheduled after
free_netdev() in __ena_shutoff(), which would create an access to freed
memory in adapter->flags.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
New devices add a new hardware acceleration engine, which adds some
restrictions to the driver.
Metadata descriptor must be present for each packet and the maximum
burst size between two doorbells is now limited to a number
advertised by the device.
This patch adds:
1. A handshake protocol between the driver and the device, so the
device will enable the accelerated queues only when both sides
support it.
2. The driver support for the new acceleration engine:
2.1. Send metadata descriptor for each Tx packet.
2.2. Limit the number of packets sent between doorbells.(*)
(*) A previous driver implementation of this feature was comitted in
commit 05d62ca218 ("net: ena: add handling of llq max tx burst size")
however the design of the interface between the driver and device
changed since then. This change is reflected in this commit.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ENA device resets to recover from some error state, all LLQ
configuration values are reset to their defaults, because LLQ is
initialized only once during ena_probe().
Changes in this commit:
1. Move the LLQ configuration process into ena_init_device()
which is called from both ena_probe() and ena_restore_device(). This
way, LLQ setup configurations that are different from the default
values will survive resets.
2. Extract the LLQ bar mapping to ena_map_llq_bar(),
and call once in the lifetime of the driver from ena_probe(),
since there is no need to unmap and map the LLQ bar again every reset.
3. Map the LLQ bar if it exists, regardless if initialization of LLQ
placement policy (ENA_ADMIN_PLACEMENT_POLICY_DEV) succeeded
or not. Initialization might fail the first time, falling back to the
ENA_ADMIN_PLACEMENT_POLICY_HOST placement policy, but later succeed
after device reset, in which case the LLQ bar needs to be mapped
already.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the rss_configurable_function_key bit to driver_supported_feature.
This bit tells the device that the driver in question supports the
retrieving and updating of RSS function and hash key, and therefore
the device should allow RSS function and key manipulation.
This commit turns on device support for hash key and RSS function
management. Without this commit this feature is turned off at the
device and appears to the user as unsupported.
This commit concludes the following series of already merged commits:
commit 0af3c4e2ea ("net: ena: changes to RSS hash key allocation")
commit c1bd17e51c ("net: ena: change default RSS hash function to Toeplitz")
commit f66c2ea3b1 ("net: ena: allow setting the hash function without changing the key")
commit e9a1de378d ("net: ena: fix error returning in ena_com_get_hash_function()")
commit 80f8443fcd ("net: ena: avoid unnecessary admin command when RSS function set fails")
commit 6a4f7dc82d ("net: ena: rss: do not allocate key when not supported")
commit 0d1c3de7b8 ("net: ena: fix incorrect default RSS key")
The above commits represent the last part of the implementation of
this feature, and with them merged the feature can be enabled
in the device.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for traffic mirroring, where the hardware reads the
buffer from the instance memory directly.
Traffic Mirroring needs access to the rx buffers in the instance.
To have this access, this patch:
1. Changes the code to map and unmap the rx buffers bidirectionally.
2. Enables the relevant bit in driver_supported_features to indicate
to the FW that this driver supports traffic mirroring.
Rx completion is not generated until mirroring is done to avoid
the situation where the driver changes the buffer before it is
mirrored.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 4.8 reports a warning when initializing with = {0}.
Dropping the "0" from the braces fixes the issue.
This fix is not ANSI compatible but is allowed by gcc.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For an overview of the race created by this patch goto synchronization
label.
In napi busy-poll mode, the kernel invokes the napi handler of the
device repeatedly to poll the NIC's receive queues. This process
repeats until a timeout, specific for each connection, is up.
By polling packets in busy-poll mode the user may gain lower latency
and higher throughput (since the kernel no longer waits for interrupts
to poll the queues) in expense of CPU usage.
Upon completing a napi routine, the driver checks whether
the routine was called by an interrupt handler. If so, the driver
re-enables interrupts for the device. This is needed since an
interrupt routine invocation disables future invocations until
explicitly re-enabled.
The driver avoids re-enabling the interrupts if they were not disabled
in the first place (e.g. if driver in busy mode).
Originally, the driver checked whether interrupt re-enabling is needed
by reading the 'ena_napi->unmask_interrupt' variable. This atomic
variable was set upon interrupt and cleared after re-enabling it.
In the 4.10 Linux version, the 'napi_complete_done' call was changed
so that it returns 'false' when device should not re-enable
interrupts, and 'true' otherwise. The change includes reading the
"NAPIF_STATE_IN_BUSY_POLL" flag to check if the napi call is in
busy-poll mode, and if so, return 'false'.
The driver was changed to re-enable interrupts according to this
routine's return value.
The Linux community rejected the use of the
'ena_napi->unmaunmask_interrupt' variable to determine whether
unmasking is needed, and urged to use napi_napi_complete_done()
return value solely.
See https://lore.kernel.org/patchwork/patch/741149/ for more details
As explained, a busy-poll session exists for a specified timeout
value, after which it exits the busy-poll mode and re-enters it later.
This leads to many invocations of the napi handler where
napi_complete_done() false indicates that interrupts should be
re-enabled.
This creates a bug in which the interrupts are re-enabled
unnecessarily.
To reproduce this bug:
1) echo 50 | sudo tee /proc/sys/net/core/busy_poll
2) echo 50 | sudo tee /proc/sys/net/core/busy_read
3) Add counters that check whether
'ena_unmask_interrupt(tx_ring, rx_ring);'
is called without disabling the interrupts in the first
place (i.e. with calling the interrupt routine
ena_intr_msix_io())
Steps 1+2 enable busy-poll as the default mode for new connections.
The busy poll routine rearms the interrupts after every session by
design, and so we need to add an extra check that the interrupts were
masked in the first place.
synchronization:
This patch introduces a race between the interrupt handler
ena_intr_msix_io() and the napi routine ena_io_poll().
Some macros and instruction were added to prevent this race from leaving
the interrupts masked. The following specifies the different race
scenarios in this patch:
1) interrupt handler and napi routine run sequentially
i) interrupt handler is called, sets 'interrupts_masked' flag and
successfully schedules the napi handler via softirq.
In this scenario the napi routine might not see the flag change
for several reasons:
a) The flag is stored in a register by the compiler. For this
case the WRITE_ONCE macro which prevents this.
b) The compiler might reorder the instruction. For this the
smp_wmb() instruction was used which implies a compiler memory
barrier.
c) On archs with weak consistency model (like ARM64) the napi
routine might be scheduled and start running before the flag
STORE instruction is committed to cache/memory. To ensure this
doesn't happen, the smp_wmb() instruction was added. It ensures
that the flag set instruction is committed before scheduling
napi.
ii) compiler reorders the flag's value check in the 'if' with
the flag set in the napi routine.
This scenario is prevented by smp_rmb() call after the flag check.
2) interrupt handler and napi routine run in parallel (can happen when
busy poll routine invokes the napi handler)
i) interrupt handler sets the flag in one core, while the napi
routine reads it in another core.
This scenario also is divided into two cases:
a) napi_complete_done() doesn't finish running, in which case
napi_sched() would just set NAPIF_STATE_MISSED and the napi
routine would reschedule itself without changing the flag's value.
b) napi_complete_done() finishes running. In this case the
napi routine might override the flag's value.
This doesn't present any rise since it later unmasks the
interrupt vector.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse build warning:
drivers/net/ethernet/amazon/ena/ena_netdev.c:2193:34: warning:
Using plain integer as NULL pointer
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Suggested-by: Joe Perches <joe@perches.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues with XDP:
1. If the XDP verdict is XDP_ABORTED we break the loop, which results in
us handling one buffer per napi cycle instead of the total budget
(usually 64). To overcome this simply change the xdp_verdict check to
!= XDP_PASS. When the verdict is XDP_PASS, the skb is not expected to
be NULL.
2. Update the residual budget for XDP_DROP and XDP_ABORTED, since
packets are handled in these cases.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending very high packet rate, the XDP tx queues can get full and
start dropping packets. In this case we don't free the pages which
results in ena driver draining the system memory.
Fix:
Simply free the pages when necessary.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
This commit reduces the driver load time by using usec resolution
instead of msec when polling for hardware state change.
Also add back-off mechanism to handle cases where minimal sleep
time is not enough.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Reorder sanity checks in get_comp_ctxt() to make more sense
2. Reorder variables in ena_com_fill_hash_function() and
ena_calc_io_queue_size() in reverse christmas tree.
3. Move around member initializations.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Join unnecessarily broken short lines in ena_com.c ena_netdev.c
2. Fix Indentations of broken lines
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix spelling and grammar mistakes in comments in ena_com.h,
ena_com.c and ena_netdev.c
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all types of variables that convey the number and sizeof queues to
be u32, for consistency with the API between the driver and device via
ena_admin_defs.h:ena_admin_get_feat_resp.max_queue_ext fields. Current
code sometimes uses int and there are multiple assignments between these
variables with different types.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ena_com_free_desc to ena_com_free_q_entries to match
the LLQ mode.
In non-LLQ mode, an entry in an IO ring corresponds to a
a descriptor. In LLQ mode an entry may correspond to several
descriptors (per LLQ definition).
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer ENA devices can write data to rx buffers with an offset
from the beginning of the buffer.
This commit adds support for this feature in the driver.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frame size ENA_PAGE_SIZE is limited to 16K on systems with larger
PAGE_SIZE than 16K. Change ENA_XDP_MAX_MTU to also take into account
the reserved tailroom.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Link: https://lore.kernel.org/bpf/158945341384.97035.907403694833419456.stgit@firesoul
The 'ENA_REGS_RESET_SHUTDOWN' enum indicates a normal driver
shutdown / removal procedure.
Also, a comment is added to one of the reset reason assignments for
code clarity.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add support for getting tx drops from the device and saving them
in the driver.
2. Report tx via netdev stats.
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Guy Tzalik <gtzalik@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unmask interrupts statistics to ethtool.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in the driver we are setting the hash function to be CRC32.
Starting with this commit we want to change the default behaviour so that
we set the hash function to be Toeplitz instead.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
00:05.0 Ethernet controller [0200]: Amazon.com, Inc. Elastic Network
Adapter (ENA) [1d0f:ec20]
Suggested-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_keep_alive_jiffies is updated in probe and when a keep-alive
event is received. In case the driver times-out on a keep-alive event,
it has high chances of continuously timing-out on keep-alive events.
This is because when the driver recovers from the keep-alive-timeout reset
the value of last_keep_alive_jiffies is very old, and if a keep-alive
event is not received before the next timer expires, the value of
last_keep_alive_jiffies will cause another keep-alive-timeout reset
and so forth in a loop.
Solution:
Update last_keep_alive_jiffies whenever the device is restored after
reset.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx req_id is an index in struct ena_eth_io_rx_cdesc_base.
The driver should validate that the Rx req_id it received from
the device is in range [0, ring_size -1]. Failure to do so could
yield to potential memory access violoation.
The validation was mistakenly done when refilling
the Rx submission queue and not in Rx completion queue.
Fixes: ad974baef2 ("net: ena: add support for out of order rx buffers refill")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug:
In short the main issue is caused by the fact that the number of queues
is changed using ethtool after ena_probe() has been called and before
ena_up() was executed. Here is the full scenario in detail:
* ena_probe() is called when the driver is loaded, the driver is not up
yet at the end of ena_probe().
* The number of queues is changed -> io_queue_count is changed as well -
ena_up() is not called since the "dev_was_up" boolean in
ena_update_queue_count() is false.
* ena_up() is called by the kernel (it's called asynchronously some
time after ena_probe()). ena_setup_io_intr() is called by ena_up() and
it uses io_queue_count to get the suitable irq lines for each msix
vector. The function ena_request_io_irq() is called right after that
and it uses msix_vecs - This value only changes during ena_probe() and
ena_restore() - to request the irq vectors. This results in "Failed to
request I/O IRQ" error for i > io_queue_count.
Numeric example:
* After ena_probe() io_queue_count = 8, msix_vecs = 9.
* The number of queues changes to 4 -> io_queue_count = 4, msix_vecs = 9.
* ena_up() is executed for the first time:
** ena_setup_io_intr() inits the vectors only up to io_queue_count.
** ena_request_io_irq() calls request_irq() and fails for i = 5.
How to reproduce:
simply run the following commands:
sudo rmmod ena && sudo insmod ena.ko;
sudo ethtool -L eth1 combined 3;
Fix:
Use ENA_MAX_MSIX_VEC(adapter->num_io_queues + adapter->xdp_num_queues)
instead of adapter->msix_vecs. We need to take XDP queues into
consideration as they need to have msix vectors assigned to them as well.
Note that the XDP cannot be attached before the driver is up and running
but in XDP mode the issue might occur when the number of queues changes
right after a reset trigger.
The ENA_MAX_MSIX_VEC simply adds one to the argument since the first msix
vector is reserved for management queue.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overview:
We don't frequently change the msix vectors throughout the life cycle of
the driver. We do so in two functions: ena_probe() and ena_restore().
ena_probe() is only called when the driver is loaded. ena_restore() on the
other hand is called during device reset / resume operations.
We use num_io_queues for calculating and allocating the number of msix
vectors. At ena_probe() this value is equal to max_num_io_queues and thus
this is not an issue, however ena_restore() might be called after the
number of io queues has changed.
A possible bug scenario is as follows:
* Change number of queues from 8 to 4.
(num_io_queues = 4, max_num_io_queues = 8, msix_vecs = 9,)
* Trigger reset occurs -> ena_restore is called.
(num_io_queues = 4, max_num_io_queues =8 , msix_vecs = 5)
* Change number of queues from 4 to 6.
(num_io_queues = 6, max_num_io_queues = 8, msix_vecs = 5)
* The driver will reset due to failure of check_for_rx_interrupt_queue()
Fix:
This can be easily fixed by always using max_num_io_queues to init the
msix_vecs, since this number won't change as opposed to num_io_queues.
Fixes: 4d19266022 ("net: ena: multiple queue creation related cleanups")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit we revert the part of
commit 1a63443afd ("net/amazon: Ensure that driver version is aligned to the linux kernel"),
which breaks the interface between the ENA driver and FW.
We also replace the use of DRIVER_VERSION with DRIVER_GENERATION
when we bring back the deleted constants that are used in interface with
ENA device FW.
This commit does not change the driver version reported to the user via
ethtool, which remains the kernel version.
Fixes: 1a63443afd ("net/amazon: Ensure that driver version is aligned to the linux kernel")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upstream drivers are managed inside global repository and released all
together, this ensure that driver version is the same as linux kernel,
so update amazon drivers to properly reflect it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From the documentation of round_jiffies():
"Rounds a time delta in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."
There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.
Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().
Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.
Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().
Fixes: 82ef30f13b ("net: ena: add hardware hints capability to the driver")
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amazon/ena/ena_netdev.c: In function ena_xdp_xmit_buff:
drivers/net/ethernet/amazon/ena/ena_netdev.c:316:19: warning:
variable rx_ring set but not used [-Wunused-but-set-variable]
commit 548c4940b9 ("net: ena: Implement XDP_TX action")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
