The LDO28 is used only on Odroid XU3 for Display Port. Define it so DTS
will describe entire hardware.
Depending on bootloader behavior this might affect the Display Port
because none of drivers are enabling it. By default it is off in S2MPS11
PMIC reset values. However it could be enabled by bootloader so in such
case kernel will later disable it as unused regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Disable unused PMIC regulators on Exynos5422 Odroid boards to reduce
energy used. According to schematics:
1. LDO12, LDO16 and LDO24 are not connected,
2. LDO26 is not used on Odroid HC1.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define LDO2, LDO23 and LDO27 critical board regulators to describe the
hardware.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find arch/arm/boot/dts -type f \( -iname "*.dts" -o -iname "*.dtsi" \) -exec sed -i \
-e "s/@\([0-9a-fA-FxX\.;:#]\+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 \
{/g" -e "s/@0\+\(.\+\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve also a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[krzk: Rerun the command to include few more changes, adjust the commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. Correct voltage on LDO15 to 3.3V and the name
of LDO17 to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no built-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for built-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
