To use the "earlycon" kernel command line parameter (without arguments)
we need a stdout-path property under the /chosen node. Add this to make
it easier to spot errors early in the boot process when looking for
them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Odroid-C1 exposes ADC channels 0 and 1 on the GPIO headers. NOTE: Due
to the SoC design these are limited to 1.8V (instead of 3.3V like all
other pins).
Enable the SAR ADC to enable voltage measurements on these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are multiple fixed regulators on the Odroid-C1 board. Add them so
they can be used when we add the devices that need them (SAR ADC needs
the 1.8V IOREF, RTC needs VDD_RTC).
These are:
- P5V0 is the main 5V power input
- VCC3V3 / VDDIO_AO3V3 / VDD3V3: fixed regulator with 3.3V output which
is supplied by P5V0
- IOREF_1V8 / VCC1V8 / VDD1V8: fixed regulator with 1.8V output which is
supplied by P5V0
- VDD_RTC: fixed voltage regulator with 0.9V output which is supplied by
VDDIO_AO3V3
- DDR_VDDC / DDR3_1V5: fixed voltage regulator with 1.5V output which is
supplied by P5V0
- the existing TF_IO and RFLASH_VDD_EN regulators are supplied by
VDDIO_AO3V3
- the existing VCCK regulator is supplied by P5V0
This does not add the missing VDDEE regulator (controlled by PWM_D)
because it's not clear yet how to configure the voltage of that
regulator.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The CPU voltage regulator is a "Monolithic Power Systems MP2161"
(according to the Odroid-C1+'s schematics). It is driven by PWM_C on
GPIODV_9.
Hardkernel's 3.10 kernel (based on the Amlogic GPL kernel sources)
defines a PWM voltage table with the following values:
- 0.86 volts = PWM register value 0x10f001b
- (more values in 0.1 volt increments)
- 1.14 volts = PWM register value 0x000012a
When using the XTAL (24MHz) as input this translates into a PWM period
of 12218ns with 0.86V using a duty cycle of 91% and 1.14V using a duty
cycle of 0%.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Odroid-C1 comes with an IR receiver. It is connected to the GPIOAO_7
pin and thus using the SoC's internal IR decoder.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This makes it easier to find existing nodes. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Odroid C1 features a microSD slot. This patch adds the necessary
DT bindings to support it.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Odroid-C1+ board is equipped with an RTL8211F ethernet PHY
which supports 10/100/1000 Mbps ethernet.
The PHY reset and interrupt lines are controlled by the SoC via
two GPIO lines (GPIOH_4 and GPIOH_3 respectively).
The PHY energy efficient ethernet (eee) mode is marked as broken
using "eee-broken-1000t" because, during tests, high packet losses
were experienced without it.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch enables the USB Host controller (USB1) and the relative USB2 PHY
on Odroid-C1/C1+ board.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the blue status LED to the Hardkernel Odroid C1 board DTS.
Signed-off-by: <edward.cragg@codethink.co.uk>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
