The Allwinner R40 SoC has the EMAC controller supported by dwmac-sun8i.
It is named "GMAC", while EMAC refers to the 10/100 Mbps Ethernet
controller supported by sun4i-emac. The controller is the same, but
the R40 has the glue layer controls in the clock control unit (CCU),
with a reduced RX delay chain, and no TX delay chain.
This patch adds the R40 specific bits to the dwmac-sun8i binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syscon property is used to point to the device that holds the glue
layer control register known as the "EMAC (or GMAC) clock register".
We do not need to explicitly list what compatible strings are needed, as
this information is readily available in the user manuals. Also the
"syscon" device type is more of an implementation detail. There are many
ways to access a register not in a device's address range, the syscon
interface being the most generic and unrestricted one.
Simplify the description so that it says what it is supposed to
describe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A83T syscon compatible was appended to the syscon compatibles list,
instead of inserted in to preserve the ordering.
Move it to the proper place to keep the list sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock delay chains found in the glue layer for dwmac-sun8i are only
used with RGMII PHYs. They are not intended for non-RGMII PHYs, such as
MII external PHYs or the internal PHY. Also, a recent SoC has a smaller
range of possible values for the delay chain.
This patch reformats the delay chain section of the device tree binding
to make it clear that the delay chains only apply to RGMII PHYs, and
make it easier to add the R40-specific bits later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add documentation about the MDIO switch used on sun8i-h3-emac
for integrated PHY.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore dt-bindings documentation about dwmac-sun8i
This reverts commit 8aa33ec2f4 ("dt-bindings: net: Revert sun8i dwmac binding")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This binding still doesn't please everyone, and we're getting far too
close from the release to allow it to reach a stable version.
Let's remove it until the discussion settles down.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s SoC has a Ethernet MAC like the one in Allwinner H3, but
have no external MII capability. That means that it can only use the
EPHY and cannot do Gbps transmission.
Add binding for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for Device-Tree bindings for the
Allwinner dwmac-sun8i driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai