The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for
MMC IO supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The padconf register WAKEUP_EN is now handled in a generic way using
Linux wakeirqs where pinctrl-single toggles the WAKEUP_EN bit when
a wakeirq is enabled or disabled.
At least omap5 gets confused if the WAKEUP_EN bit is set and the pin
is not claimed as a wakeirq. The end result is that wakeirqs don't
work properly as there is nothing handling the wakeirq.
So let's just remove the WAKEUP_EN usage from dts files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3_pmx_core pinmux device in the device tree handles the system
controller module (SCM) PADCONFS fonction. Its control registers are
split in two distinct areas, with other SCM registers in-between. Those
other registers can't thus be requested by other drivers as the memory
region gets reserved by the pinmux driver.
Split the omap3_pmx_core device tree node in two for the two memory
regions. The second region address and size depends on the SoC model.
The change in omap3.dtsi fixes an "external abort on non-linefetch" when
doing
cat /sys/kernel/debug/pinctrl/.../pins
on a Nokia N900.
Note that the core2 padconf region is different for 3430 vs 3630,
and does not exist on 3517 as noted by Nishanth Menon <nm@ti.com>.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Sebastian Reichel <sre@debian.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 based on Nishant's patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren