The barriers are redundant because atomic_test_and_clear_bit() already
provides the required full ordering for the cases in question (that is,
when the bit is cleared).
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Intel "new" controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace the BT_ERR functions with bt_dev_err to get a consistent error
printout that always prefixes the HCI device identifier.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Issue description: Intel 7265 shares the same RF with Wifi and BT.
In the shutdown scenario turn off BT, followed by turn WiFi off
and on causing error in RF calibration in WiFi Module
Solution: before shutdown BT ensure any RF activity to clear by
HCI reset command.
Reference Logs:
ERR kernel: [ 386.193284] iwlwifi 0000:01:00.0: Failed to run INIT calibrations: -5
ERR kernel: [ 386.193298] iwlwifi 0000:01:00.0: Failed to run INIT ucode: -5
ERR kernel: [ 386.193309] iwlwifi 0000:01:00.0: Failed to start RT ucode: -5
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Singed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by btusb_send_frame_intel(),
which is set to hdev->send, and hdev->send() is never
called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The USB completion callback does not disable interrupts while acquiring
the ->lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave variant of the locking primitives.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Dell Inspiron 5565 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=15750392
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") we tried to address the non-working Atheros BT devices
by changing the quirk from BTUSB_ATH3012 to BTUSB_QCA_ROME. This made
such devices working while it turned out to break other existing chips
with the very same USB ID, hence it was reverted afterwards.
This is another attempt to tackle the issue. The essential point to
use BTUSB_QCA_ROME is to apply the btusb_setup_qca() and do RAM-
patching. And the previous attempt failed because btusb_setup_qca()
returns -ENODEV if the ROM version doesn't match with the expected
ones. For some devices that have already the "correct" ROM versions,
we may just skip the setup procedure and continue the rest.
So, the first fix we'll need is to add a check of the ROM version in
the function to skip the setup if the ROM version looks already sane,
so that it can be applied for all ath devices.
However, the world is a bit more complex than that simple solution.
Since BTUSB_ATH3012 quirk checks the bcdDevice and bails out when it's
0x0001 at the beginning of probing, so the device probe always aborts
here.
In this patch, we add another check of ROM version again, and if the
device needs patching, the probe continues. For that, a slight
refactoring of btusb_qca_send_vendor_req() was required so that the
probe function can pass usb_device pointer directly before allocating
hci_dev stuff.
Fixes: commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174")
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1082504
Tested-by: Ivan Levshin <ivan.levshin@microfocus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Dell XPS 13 9360 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Garrett LeSage <glesage@redhat.com>
Reported-and-tested-by: Garrett LeSage <glesage@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeremy Cline correctly points out in rhbz#1514836 that a device where the
QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship
with a different wifi/bt chipset in some configurations.
If that is the case then we are needlessly penalizing those other chipsets
with a reset-resume quirk, typically causing 0.4W extra power use because
this disables runtime-pm.
This commit moves the DMI table check to a btusb_check_needs_reset_resume()
helper (so that we can easily also call it for other chipsets) and calls
this new helper only for QCA_ROME chipsets for now.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Jeremy Cline <jcline@redhat.com>
Suggested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") is causing bluetooth to no longer work for several
people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911
So lets revert it for now and try to find another solution for
devices which need the modified quirk.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Vic Wei <vwei@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.
Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c6 ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.
So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.
Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA ...")
Cc: stable@vger.kernel.org
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kevin Fenzi <kevin@scrye.com>
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Asus Z370-I contains a Realtek RTL8822BE device with an associated
BT chip using a USB ID of 0b05:185c. This device is added to the driver.
Signed-off-by: Hon Weng Chong <honwchong@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The firmware download flow for RAM SKU is same for both USB and UART
and this patch creates a common function for both driver.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel_Read_Boot_Params command is used to read boot parameters
from the bootloader and this is Intel generic command used in USB
and UART drivers.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Each RAM SKU has a different boot parameter which is used in
HCI_Intel_Reset command after downloading the firmware.
The boot parameter is embedded in the firmware data and to support
multiple SKUs, driver reads the boot parameter while downloading
the firmware instead of using static values per SKU.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel_Reset command is used to reset the device after downloading
the firmware and this is Intel generic command used in both USB and
UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 7d06d5895c ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices,
instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c.
This was done because the DIY BTUSB_RESET_RESUME reset-resume handling
has several issues (see the original commit message). An added advantage
of moving over to the USB-core reset-resume handling is that it also
disables autosuspend for these devices, which is similarly broken on these.
But there are 2 issues with this approach:
1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek
devices.
2) Sofar only 2 of the 10 QCA devices known to the btusb code have been
added to usb/core/quirks.c and if we fix the Realtek case the same way
we need to add an additional 14 entries. So in essence we need to
duplicate a large part of the usb_device_id table in btusb.c in
usb/core/quirks.c and manually keep them in sync.
This commit instead restores setting a reset-resume quirk for QCA devices
in the btusb.c code, avoiding the duplicate usb_device_id table problem.
This commit avoids the problems with the original DIY BTUSB_RESET_RESUME
code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the
usb_device.
This commit also moves the BTUSB_REALTEK case over to directly setting the
USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused
BTUSB_RESET_RESUME code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 7d06d5895c ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
Cc: stable@vger.kernel.org
Cc: Leif Liddy <leif.linux@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit fd865802c6.
This commit causes a regression on some QCA ROME chips. The USB device
reset happens in btusb_open(), hence firmware loading gets interrupted.
Furthermore, this commit stops working after commit
("a0085f2510e8976614ad8f766b209448b385492f Bluetooth: btusb: driver to
enable the usb-wakeup feature"). Reset-resume quirk only gets enabled in
btusb_suspend() when it's not a wakeup source.
If we really want to reset the USB device, we need to do it before
btusb_open(). Let's handle it in drivers/usb/core/quirks.c.
Cc: stable@vger.kernel.org
Cc: Leif Liddy <leif.linux@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Daniel Drake <drake@endlessm.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.
Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).
The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.
Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
But for the SKU's 9x60, there a 3 variants of FW, which cannot be
differentiated just with hw_variant and devision_revision_id.
So to pick the appropriate FW file for 9x60 SKU's, it will be
differentiated using hw_variant, hw_revision and fw_revision rather
than hw_variant and device_revision_id only.
Format will be like this:
ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi and .ddc
Signed-off-by: Jaya P G <jaya.p.g@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit 9834e586fa ("Bluetooth: btusb: Add workaround for Broadcom devices
without product id") was added to deal with the BT part of the BCM4356A2
on GPD pocket laptops having an usb vid:pid of 0000:0000.
After another commit to add support for the BCM UART connected BT ACPI-id
BCM2E7E used on the GPD win, it turns out that the BT on the GPD pocket is
connected via both USB and UART. Adding support for the BCM2E7E ACPI-id
causes it to switch to UART mode.
The Windows shipped with the device is using it in UART mode and the
presence of the BCM2E7E ACPI-id combined with the all 0 USB vid:pid
indicates that the BT part was never meant to be used in USB mode.
With the recent patches to use serdev device enumeration / instantiation
for UART attached ACPI enumerated BT devices, everything work OOTB in UART
mode and the workaround for the all 0 USB vid:pid is no longer needed.
This reverts commit 9834e586fa ("Bluetooth: btusb: Add workaround for
Broadcom devices without product id").
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BT-Controller connected as platform non-root-hub device and
usb-driver initialize such device with wakeup disabled,
Ref. usb_new_device().
At present wakeup-capability get enabled by hid-input device from usb
function driver(e.g. BT HID device) at runtime. Again some functional
driver does not set usb-wakeup capability(e.g LE HID device implement
as HID-over-GATT), and can't wakeup the host on USB.
Most of the device operation (such as mass storage) initiated from host
(except HID) and USB wakeup aligned with host resume procedure. For BT
device, usb-wakeup capability need to enable form btusc driver as a
generic solution for multiple profile use case and required for USB remote
wakeup (in-bus wakeup) while host is suspended. Also usb-wakeup feature
need to enable/disable with HCI interface up and down.
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently we are calling usb_submit_urb directly to submit deferred tx
urbs after unanchor them.
So the usb_giveback_urb_bh would failed to unref it in usb_unanchor_urb
and cause memory leak:
unreferenced object 0xffffffc0ce0fa400 (size 256):
...
backtrace:
[<ffffffc00034a9a8>] __save_stack_trace+0x48/0x6c
[<ffffffc00034b088>] create_object+0x138/0x254
[<ffffffc0009d5504>] kmemleak_alloc+0x58/0x8c
[<ffffffc000345f78>] __kmalloc+0x1d4/0x2a0
[<ffffffc0006765bc>] usb_alloc_urb+0x30/0x60
[<ffffffbffc128598>] alloc_ctrl_urb+0x38/0x120 [btusb]
[<ffffffbffc129e7c>] btusb_send_frame+0x64/0xf8 [btusb]
Put those urbs in tx_anchor to avoid the leak, and also fix the error
handling.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed alignment of all block comments.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's been numerous reported instances where BTUSB_QCA_ROME
bluetooth controllers stop functioning upon resume from suspend. These
devices seem to be losing power during suspend. Patch will detect a status
change on resume and perform a reset.
Signed-off-by: Leif Liddy <leif.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Raghuram Hegde