Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).
Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.
In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.
Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.
We vastly simplify mac filters by removing
(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs
Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-09-22
This series contains updates to i40e and i40evf only.
Sridhar fixes link state event handling by updating the carrier and
starts/stops the Tx queues based on the link state notification from PF.
Brady fixes an issue where a user defined RSS hash key was not being
set because a user defined indirection table is not supplied when changing
the hash key, so if an indirection table is not supplied now, then a
default one is created and the hash key is correctly set. Also fixed
an issue where when NPAR was enabled, we were still using pf->mac_seid
to perform the dump port query. Instead, go through the VSI to determine
the correct ID to use in either case.
Mitch provides one fix where a conditional return code was reversed, so
he does a "switheroo" to fix the issue.
Carolyn has two fixes, first fixes an issue in the virt channel code,
where a return code was not checked for NULL when applicable. Second,
fixes an issue where we were byte swapping the port parameter, then
byte swapping it again in function execution.
Colin Ian King fixes a potential NULL pointer dereference.
Bimmy changes up i40evf_up_complete() to be void since it always returns
success anyways, which allows cleaning up of code which checked the
return code from this function.
Alex fixed an issue where the driver was incorrectly assuming that we
would always be pulling no more than 1 descriptor from each fragment.
So to correct this, we just need to make certain to test all the way to
the end of the fragments as it is possible for us to span 2 descriptors
in the block before us so we need to guarantee that even the last 6
descriptors have enough data to fill a full frame.
v2: dropped patches 1-3, 10 and 12 from the original series since Or
Gerlitz pointed out several areas of improvement in the implementation
of the VF Port representor netdev. Sridhar is re-working the series
for later submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue in the virt channel code, where a return
from i40e_find_vsi_from_id was not checked for NULL when applicable.
Without this patch, there is a risk for panic and static analysis
tools complain. This patch fixes the problem by adding the check
and adding an additional input check for similar reasons.
Change-ID: I7e9be88eb7a3addb50eadc451c8336d9e06f5394
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This conditional is backward, so the driver responds back to the VF with
the wrong opcode. Do the old switcheroo to fix this.
Change-ID: I384035b0fef8a3881c176de4b4672009b3400b25
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables
ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we allocate memory, we must free it. It's simple courtesy.
Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.
Also changing the call order of VF enable, calling it after VF creation
rather than before.
Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.
Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.
Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.
Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newly added code in i40e_vc_config_promiscuous_mode_msg() is indented
in a way that gcc rightly complains about:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function 'i40e_vc_config_promiscuous_mode_msg':
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1543:4: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
if (f->vlan >= 0 && f->vlan <= I40E_MAX_VLANID)
^~
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1550:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'if'
aq_err = pf->hw.aq.asq_last_status;
From the context, it looks like the aq_err assignment was meant to be
inside of the conditional expression, so I'm adding the appropriate
curly braces now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5676a8b9cd ("i40e: Add VF promiscuous mode driver support")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Some of the split related context set up code stays in
i40e_virtchnl_pf.c in case an older VF driver tries to load
and still wants to use packet split.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have an uninitialized variable warning for valid_len for one case in
validate_vf_mesg. To fix this, just initialize it to 0 at the top of the
function and remove all of the now redundant assignments to 0 in the
individual cases.
Change-Id: Iacbd97f4c521ed8d662eef803a598d8707708cfd
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is privileged/trusted it can do as it may please including
but not limited to hogging resources and playing unfair.
But if the VF is not privileged/trusted it still can add some number
(8) of MAC and VLAN addresses.
Other restrictions with respect to Port VLAN and normal VLAN still apply
to not privileged/trusted VF.
Change-Id: I3a9529201b184c8873e1ad2e300aff468c9e6296
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure a VF is not trusted/privileged until its explicitly
set for trust through the new NDO op interface.
Change-Id: I476385c290d2b4901d8fceb29de43546accdc499
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add necessary Linux Ethernet driver support for promiscuous mode
operation. Add a flag so the VF knows it is in promiscuous mode
and two state flags to discreetly track multicast and unicast
promiscuous states.
Change-Id: Ib2f2dc7a7582304fec90fc917ebb7ded21ba1de4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VFs can request their queues to be set up into polling mode, rather
than interrupt mode, which works well for supporting things like DPDK,
but this should not be available when working in an multi-function
support device.
Change-ID: Id36792e4e7422db8f2033336507211f68f14ff6f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds hook to support changing a VF from not-trusted
to trusted and vice-versa. Fixed the wrappers and function prototype.
Changed the dmesg to reflex the current state better. This patch also
disables turning on/off trusted VF in MFP mode.
Change-ID: Ibcd910935c01f0be1f3fdd6d427230291ee92ebe
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the HW flush routine to the end of the reset flow,
after the completion of writing to the device VFLR registers- the
benefit is to avoid problems in the passthrough routines.
Change-ID: Ieb56866f21895e6c1fc514b7328c3df79807a57c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit immediately after triggering a reset instead of
waiting until after cleanup is complete. Make sure to trigger a reset
every time, not just if the PF is up.
These changes fix a problem where VF resets would get lost by the PF,
preventing the VF driver from initializing.
Change-ID: I5945cf2884095b7b0554867c64df8617e71d9d29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is vestigial, a remnant of the primordial code from which
this driver spawned. We can safely remove it.
Change-ID: I24e0fe338e7c7c50d27dc5515564f33caefbb93a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit after reset processing, instead of before. This
prevents double resets on VF init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If we reset a VF, its VSI goes away, and it gets a new one. So don't
hang on to the now-stale local VSI pointer. It just leads to suffering
and kernel panics.
Change-ID: Ia8823b4e85893e95e963acee284968022b29177a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive. We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.
Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explain why we cannot remove this code, even though it works differently
than any of our other interrupt cause handling code.
Change-ID: Ie66203bd037a466066036611c31d44f759ec5176
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a define for this, use it. No functional change.
Change-ID: Ic0e3ea4f562e46de63b2a8de07f291ccc10205fd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calculating TX bandwidth for VFs, we need to know the link speed to
make sure we don't allocate more bandwidth than is available. Add 20G
link speed to the switch statement so we can support devices that link
at that speed.
Change-ID: I5409f6139d549e5832777db9c22ca0664e0c5f8b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add write-back on interrupt throttle rate timer expiration support
for the i40evf driver, when running on X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PCTYPES for the X710 and X722 families are different. This patch
makes adjustments for that.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the user to specify a zero MAC address for VFs. This removes the
existing MAC address and allows the VF to use a random address. Libvirt
does this normally when removing a VF from a VM.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are being reset, there is a brief window of time when they
cannot be configured because they don't have a VSI to configure. If
a script is quick, it can fall through that window. To avoid
defenestration, log a useful error message and return -EAGAIN.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Operators should have spaces around them.
Change-ID: I64735e9aa8618b9a5059a87ace1c999d6d3bfcfb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we get an invalid message from a VF, we should tell the user which VF
is being naughty, rather than making them guess.
Change-ID: I9252cef7baea3d8584043ed6ff12619a94e2f99c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller