IT913x tuner driver disables own clock, provided by demod core, as
very a first operation when tuner is put on *sleep*. That likely
causes failure of all the rest commands on sleep sequence, which
leads situation where tuner is not actually on sleep, but consuming
a lot of power.
I measured 102mA current consumption from the USB before change
and after change it was only 32mA. Used device was single tuner
IT9135 BX.
Second reason to remove that register from tuner driver is reason
it is simply on wrong driver (demod vs. tuner), breaking the
principle of correct driver.
Clock is now provided more correctly af9033 demod driver as a
config option.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is 2 different versions of that chip available, master and
slave. Slave is used only on dual tuner devices with master tuner.
Laser printing top of chip is 18212/M or 18212/S according to chip
version.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable into state to keep track if firmware has been loaded or not.
Skip firmware loading in case it is already loaded (resume from sleep).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of sending command 13 to the tuner, send command 16 when sleeping. This
behaviour is observed when using manufacturer provided binary-only Linux driver
for TechnoTrend CT2-4400 (Windows driver does not do power management).
The issue with command 13 is that firmware loading is necessary after that.
This is not an issue with tuners that do not require firmware, but starting
streaming after sleep on an Si2158 takes noticeable time as firmware is
loaded on resume.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
It is driver internal function and does not need anything from
frontend structure. Due to that change parameter type to driver
state which is better for driver internal functions.
Also remove one unused variable from state itself.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
foo_dev seems to be most correct term for the structure holding data
of each device instance. It is most used term in Kernel and also
examples from book Linux Device Drivers, Third Edition, uses it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That register is needed to program very first in order to operate
correctly.
[crope@iki.fi: returned sequence back, removed sleep, moved reg
write earlier to prevent populating tuner ops in case of failure]
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/tuners/tuner-xc2028.c:182:2-18: code aligned with following code on line 183
drivers/media/tuners/tuner-xc2028.c:184:2-19: code aligned with following code on line 185
drivers/media/tuners/tuner-xc2028.c:186:2-19: code aligned with following code on line 187
drivers/media/tuners/tuner-xc2028.c:188:2-17: code aligned with following code on line 189
drivers/media/tuners/tuner-xc2028.c:190:2-19: code aligned with following code on line 191
drivers/media/tuners/tuner-xc2028.c:192:2-19: code aligned with following code on line 193
drivers/media/tuners/tuner-xc2028.c:194:2-18: code aligned with following code on line 195
drivers/media/tuners/tuner-xc2028.c:196:2-17: code aligned with following code on line 197
drivers/media/tuners/tuner-xc2028.c:198:2-18: code aligned with following code on line 199
drivers/media/tuners/tuner-xc2028.c:200:2-19: code aligned with following code on line 201
drivers/media/tuners/tuner-xc2028.c:202:2-18: code aligned with following code on line 203
drivers/media/tuners/tuner-xc2028.c:204:2-16: code aligned with following code on line 205
drivers/media/tuners/tuner-xc2028.c:206:2-20: code aligned with following code on line 207
drivers/media/tuners/tuner-xc2028.c:208:2-17: code aligned with following code on line 209
drivers/media/tuners/tuner-xc2028.c:210:2-18: code aligned with following code on line 211
drivers/media/tuners/tuner-xc2028.c:212:2-18: code aligned with following code on line 213
drivers/media/tuners/tuner-xc2028.c:214:2-18: code aligned with following code on line 215
drivers/media/tuners/tuner-xc2028.c:216:2-16: code aligned with following code on line 217
drivers/media/tuners/tuner-xc2028.c:218:2-18: code aligned with following code on line 219
drivers/media/tuners/tuner-xc2028.c:220:2-20: code aligned with following code on line 221
drivers/media/tuners/tuner-xc2028.c:222:2-21: code aligned with following code on line 223
drivers/media/tuners/tuner-xc2028.c:224:2-20: code aligned with following code on line 225
drivers/media/tuners/tuner-xc2028.c:226:2-23: code aligned with following code on line 227
drivers/media/tuners/tuner-xc2028.c:228:2-23: code aligned with following code on line 229
drivers/media/tuners/tuner-xc2028.c:230:2-22: code aligned with following code on line 231
drivers/media/tuners/tuner-xc2028.c:232:2-24: code aligned with following code on line 233
drivers/media/tuners/tuner-xc2028.c:234:2-19: code aligned with following code on line 235
drivers/media/tuners/tuner-xc2028.c:236:2-19: code aligned with following code on line 237
drivers/media/tuners/tuner-xc2028.c:238:2-20: code aligned with following code on line 239
drivers/media/tuners/tuner-xc2028.c:240:2-19: code aligned with following code on line 241
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/tuners/xc4000.c:573:2-28: code aligned with following code on line 574
drivers/media/tuners/xc4000.c:575:2-29: code aligned with following code on line 576
drivers/media/tuners/xc4000.c:577:2-29: code aligned with following code on line 578
drivers/media/tuners/xc4000.c:579:2-27: code aligned with following code on line 580
drivers/media/tuners/xc4000.c:581:2-29: code aligned with following code on line 582
drivers/media/tuners/xc4000.c:583:2-29: code aligned with following code on line 584
drivers/media/tuners/xc4000.c:585:2-28: code aligned with following code on line 586
drivers/media/tuners/xc4000.c:587:2-27: code aligned with following code on line 588
drivers/media/tuners/xc4000.c:589:2-28: code aligned with following code on line 590
drivers/media/tuners/xc4000.c:591:2-29: code aligned with following code on line 592
drivers/media/tuners/xc4000.c:593:2-28: code aligned with following code on line 594
drivers/media/tuners/xc4000.c:595:2-26: code aligned with following code on line 596
drivers/media/tuners/xc4000.c:597:2-30: code aligned with following code on line 598
drivers/media/tuners/xc4000.c:599:2-27: code aligned with following code on line 600
drivers/media/tuners/xc4000.c:601:2-28: code aligned with following code on line 602
drivers/media/tuners/xc4000.c:603:2-28: code aligned with following code on line 604
drivers/media/tuners/xc4000.c:605:2-28: code aligned with following code on line 606
drivers/media/tuners/xc4000.c:607:2-26: code aligned with following code on line 608
drivers/media/tuners/xc4000.c:609:2-28: code aligned with following code on line 610
drivers/media/tuners/xc4000.c:611:2-30: code aligned with following code on line 612
drivers/media/tuners/xc4000.c:613:2-31: code aligned with following code on line 614
drivers/media/tuners/xc4000.c:615:2-30: code aligned with following code on line 616
drivers/media/tuners/xc4000.c:617:2-33: code aligned with following code on line 618
drivers/media/tuners/xc4000.c:619:2-33: code aligned with following code on line 620
drivers/media/tuners/xc4000.c:621:2-32: code aligned with following code on line 622
drivers/media/tuners/xc4000.c:623:2-34: code aligned with following code on line 624
drivers/media/tuners/xc4000.c:625:2-29: code aligned with following code on line 626
drivers/media/tuners/xc4000.c:627:2-29: code aligned with following code on line 628
drivers/media/tuners/xc4000.c:629:2-30: code aligned with following code on line 630
drivers/media/tuners/xc4000.c:631:2-29: code aligned with following code on line 632
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using if (foo == false), just use
if (!foo).
That allows a faster mental parsing when analyzing the
code.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Maximum satellite symbol rate used is 45000000Sps which overflows
when multiplied by 135. As final calculation result is fraction,
we could use mult_frac macro in order to keep calculation inside
32 bit number limits and prevent overflow.
Original bug and fix was provided by Nibble Max. I decided to
implement it differently as it is now.
Reported-by: Nibble Max <nibble.max@gmail.com>
Tested-by: Nibble Max <nibble.max@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the property for delivery system also in case of SYS_ATSC. This
behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same thing for si2157 as Antti did earlier for tda18212:
There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
While here, fix a typo ("unknown") in si2157_init.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that xc5000_set_params() is also called during resume,
move the code that checks for the firmware to happen there.
This way, the firmware will be loaded either for analog or
digital TV when .resume callback is called.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
xc5000_set_params() is a bad name for a function that
handles only digital TV. Rename it to xc5000_set_digital_params(),
and proper name the generic function that works for both
digital and analog.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As we need a function that reapply the last tuned radio,
in order to do resume, split the code that validates and
updates the internal priv struct from the ones that
actually set radio and TV.
A latter patch will add support for resume.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As we'll be adding a code to resume tuner operation, we
need to move the code that actually sets DTV on a separate
function, to be called by the resume code.
No functional changes, just code got moved.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
After xc5000 stops working, it waits for 5 seconds, waiting
for a new usage. Only after that it goes to low power mode.
If a suspend event happens before that, a work queue will
remain active, with causes suspend to crash.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On a normal condition, no errors should happen at xc5000
firmware upload is done. So, print at the dmesg if something
bad happens.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, firmware retry logic keeps reading from FS every
time during the retry logic. This is not needed. Instead,
only release the firmware read after success.
While here, make the non-debug messages less verbose, as it
only matters to the user if the firmware was successfully
loaded, or if some error happened.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the current code, if something bad happens during the
firmware init process, the device will keep trying forever,
and removing it would cause an OOPS.
Instead, try only a limited amount of time. If not, fails.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The programmed frequency on xc4000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
This works fine on set_frontend, as the device calculates
the needed offset. However, at get_frequency(), the returned
value is the initial frequency. That's generally not a big
problem on most drivers, however, starting with changeset
6fe1099c7a, the frequency drift is taken into account at
dib7000p driver.
This broke support for PCTV 340e, with uses dib7000p demod and
xc4000 tuner.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The programmed frequency on xc5000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This meta-tag is used by some distros to help them package
the firmware and generate proper initrd images.
So, add the firmware names there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware name at:
http://www.kernellabs.com/firmware/xc4000/
Is different from the one at the Kernel. Update it
try first the new name, falling back to the previous one
if the new name can't be found.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
warning: (VIDEO_PVRUSB2 && VIDEO_TLG2300 && VIDEO_USBVISION && VIDEO_GO7007 && VIDEO_AU0828_V4L2 && VIDEO_CX231XX && VIDEO_TM6000 && VIDEO_EM28XX && VIDEO_IVTV && VIDEO_MXB && VIDEO_CX18 && VIDEO_CX23885 && VIDEO_CX88 && VIDEO_BT848 && VIDEO_SAA7134 && VIDEO_SAA7164) selects VIDEO_TUNER which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_TUNER)
That happens when:
# CONFIG_MEDIA_ANALOG_TV_SUPPORT is not set
CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
# CONFIG_MEDIA_RADIO_SUPPORT is not set
# CONFIG_MEDIA_SDR_SUPPORT is not set
CONFIG_VIDEO_AU0828_V4L2=y
CONFIG_VIDEO_CX231XX=y
CONFIG_VIDEO_TM6000=y
CONFIG_VIDEO_EM28XX=y
CONFIG_VIDEO_TUNER=y
CONFIG_MEDIA_SUPPORT=y
With means that we need to enable MEDIA_TUNER also when DTV
is enabled. While the above config doesn't cover, if we enable
SDR, the same error can also happen.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct prototype is defined at the beginning of the code as
"si2157_ops" but the real struct is called "si2157_tuner_ops".
This is causing the name to be empty on this info msg: si2157 16-0060:
si2157: found a '' in cold state
[crope@iki.fi: commit msg from Luis email reply]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tell used TV standard and bandwidth for tuner firmware.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Si2158 A20 chip.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move chip initialization related code from si2157_set_params to
si2157_init.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We want also read data from firmware. Add support for it. Copied from
si2168 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add static to tda m_* variables in the header. They don't need to be global.
With some cleanup they could probably even be marked const.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=68191
Reported-by: Christian Schneider <christian@ch-sc.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some drivers, like au0828 are very sensitive to tuner sleep and may
break if the sleep happens too fast. Also, by keeping the tuner alive
for a while could speedup tuning process during channel scan. So,
change the logic to delay the actual sleep to 5 seconds after its
command.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
WARNING: please, no space before tabs
+#define XC_PRODUCT_ID_FW_LOADED ^I0x1388$
WARNING: please, no space before tabs
+#define DK_SECAM_A2LDK3 ^I13$
WARNING: please, no space before tabs
+#define DK_SECAM_A2MONO ^I14$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT2 ^I21$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT1 ^I22$
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's absolutely no reason to wrap msleep() call here.
Just rename all occurences of xc_wait() with msleep() and
remove the wrapper function.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTfR2zAAoJEHm+PkMAQRiG3noH/2s+KUge3qO2M+AmxttUo74B
+npAMdbqYR3MdEiwxYZfsHcMu4Ye/IKLcrh4pydB5hI2mdjtGkH1bnmia0f1ve/c
Z/a0256+W8gWp7mcUBqSNztqLPAWa7wKOqNdLjj5idr1BSj6u8im+fQ9FBh2woki
1fyYAuq/60lq4CMOKJvkA95V1Ome/jO+8tS4PguOgsCETQxCVFGurZcBbG3Mx5Y3
v+ioCqeRc6GvxPFR6YngnTZCrsLxSRT3tnO2Qy5zX7dxjIQkCEbvIckpBQv01Y3R
wNUaX+2Jae207igxrEv8CjmCFnmZFuUI15aWWCy6fOS/j8bjuk6ThYJO8N4ZBM0=
=2ShG
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc6' into patchwork
Linux 3.15-rc6
* tag 'v3.15-rc6': (1314 commits)
Linux 3.15-rc6
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
sysfs: make sure read buffer is zeroed
ahci: imx: PLL clock needs 100us to settle down
PCI: Wrong register used to check pending traffic
target: fix memory leak on XCOPY
random: fix BUG_ON caused by accounting simplification
clk: tegra: Fix wrong value written to PLLE_AUX
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
ACPI / video: Revert native brightness quirk for ThinkPad T530
staging: rtl8723au: Use correct pipe type for USB interrupts
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
arm64: fix pud_huge() for 2-level pagetables
...
DVB-C uses lower frequencies than DVB-T. Extend frequency range down to
110 MHz in order to support DVB-C. 110 - 862 MHz range is defined by
NorDig Unified 2.2 specification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Silicon Labs Si2157 silicon tuner driver.
Currently it supports only DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was some frequency calculation overflows which caused tuning
failure on 32-bit architecture. Use 64-bit numbers where needed in
order to avoid calculation overflows.
Thanks for the Finnish person, who asked remain anonymous, reporting,
testing and suggesting the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct the initialization values at the start of the function
and use proper variable sizes to prevent overflow.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1196501: Missing break in switch (MISSING_BREAK)
I introduced that bug recently by commit
96a5b3a869.
As a result, it will flood unintentionally error message to log.
Reported-by: <scan-admin@coverity.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That tuner driver is mainly for DVB API, but there is some V4L2 API
controls for SDR usage. Make driver compile conditional so that V4L2
is not mandatory. Without the V4L2 support driver is build as a DVB
only, without SDR controls.
Fixes following errors reported by kbuild test robot:
ERROR: "v4l2_ctrl_auto_cluster" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_new_std" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_init_class" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_free" [drivers/media/tuners/e4000.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All error/warnings:
drivers/built-in.o: In function `e4000_set_params':
>> e4000.c:(.text+0x1219a1b): undefined reference to `__umoddi3'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename some variables.
Change error status checks from (ret < 0) to (ret).
No actual functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That comes possible after driver was converted to kernel I2C model
(I2C binding & proper I2C client with no gate control hack). All
nasty low level I2C routines are now covered by regmap.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Gate control is now implemented by rtl2832 I2C adapter so we do not
need proprietary DVB i2c_gate_ctrl() anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PLL lock control to get PLL lock flag status from tuner
synthesizer.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit overflow on VCO frequency calculation which blocks
tuning to 1073 - 1104 MHz. Use 64 bit number in order to avoid VCO
frequency overflow.
After that fix device in question tunes to following range:
60 - 1104 MHz
1250 - 2207 MHz
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement gain and bandwidth controls using v4l2 control framework.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver conversion from proprietary DVB tuner model to more
general I2C driver model.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is now new tuner types which are not handled on that switch-case.
Print error if unknown tuner type is meet.
drivers/media/tuners/tuner-xc2028.c: In function ‘generic_set_freq’:
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_ADC’ not handled in switch [-Wswitch]
switch (new_type) {
^
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_RF’ not handled in switch [-Wswitch]
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.
Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only send a power down command for the device if it is not already
in power down state. That prevents a timeout when trying to talk
with the device.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This macro is not used. remove it.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest checkpatch.pl has some new requirements for coding style.
Fix some of those.
* remove Free Software Foundation postal address
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
M88TS2022 is DVB-S/S2 RF tuner used usually in conjunction with
Montage M88DS3103 DVB-S/S2 demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/tuner-xc2028.c:651:1: warning: 'load_firmware' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum limit is 80, used only
on tm6000 driver. This limit is due to the size of the USB control URBs.
Ok, it would be theoretically possible to use a bigger size on PCI
devices, but the firmware load time is already good enough. Anyway,
if some usage requires more, it is just a matter of also increasing
the buffer size at load_firmware().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/e4000.c:50:1: warning: 'e4000_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/e4000.c:83:1: warning: 'e4000_rd_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:66:1: warning: 'fc2580_wr_regs.constprop.1' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:98:1: warning: 'fc2580_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:57:1: warning: 'tda18212_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:90:1: warning: 'tda18212_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:60:1: warning: 'tda18218_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:92:1: warning: 'tda18218_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no need to zero the buffer, as if the routine gets an error,
rc will be different than one.
That fixes the following warning:
drivers/media/tuners/tda9887.c: In function 'tda9887_status':
drivers/media/tuners/tda9887.c:539:2: warning: value computed is not used [-Wunused-value]
While here, make fix the CodingStyle on this function.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Small changes in order to support tuner version R828D @ 16 MHz clock.
There was 'vco_fine_tune' check, which seems to adjust synthesizer
output divider (mixer dix / LO div / Rout) by one. R828D seems to
return vco_fine_tune=1 every time and that condition causes tuning
fail as output divider was increased by one.
Resolve problem by skipping whole condition in case of R828D tuner.
Just to mention, other tuner, R820T, seems to return 2 here.
Synthesizer maximum frequency check was hard coded to check synthesizer N
and thus worked correctly only for clock frequencies around 30 MHz.
As whole test is quite useless in any case, I removed it totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable vco_select is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix long-lasting bug that causes tuning failure of some frequencies
on 32-bit arch.
Special thanks goes to Damien CABROL who finally find root of the bug.
Also big thanks to Jacek Konieczny for donating "non-working" device.
[crope@iki.fi: fix trivial merge conflict]
[m.chehab@samsung.com: add missing header file]
Reported-by: Jacek Konieczny <jajcus@jajcus.net>
Reported-by: Torsten Seyffarth <t.seyffarth@gmx.de>
Reported-by: Jan Taegert <jantaegert@gmx.net>
Reported-by: Damien CABROL <cabrol.damien@free.fr>
Tested-by: Damien CABROL <cabrol.damien@free.fr>
Tested-by: Jan Taegert <jantaegert@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I did some tests against modulator (television signal generator) and this
seems to improve sensitivity a little bit on channel I used. Used device
was able to receive transmission just as weak signal as with Windows XP.
Thanks to Jacek for donating his non-working device. I cannot ask he to
test anymore...
Reported-by: Jacek Konieczny <jajcus@jajcus.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are a large number of reports that the media build is
not compiling when some drivers are compiled as builtin, while
the needed frontends are compiled as module.
On the last one of such reports:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: saa7134-dvb.c:undefined reference to `zl10039_attach'
The .config file has:
CONFIG_VIDEO_SAA7134=y
CONFIG_VIDEO_SAA7134_DVB=y
# CONFIG_MEDIA_ATTACH is not set
CONFIG_DVB_ZL10039=m
And it produces all those errors:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2f263e): undefined reference to `tea5767_attach'
tuner-core.c:(.text+0x2f273e): undefined reference to `tda9887_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2f2d20): undefined reference to `tea5767_autodetection'
drivers/built-in.o: In function `av7110_attach':
av7110.c:(.text+0x330bda): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330bf7): undefined reference to `stv0299_attach'
av7110.c:(.text+0x330c63): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d09): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330d33): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d5d): undefined reference to `stv0297_attach'
av7110.c:(.text+0x330dbe): undefined reference to `stv0299_attach'
drivers/built-in.o: In function `tuner_attach_dtt7520x':
ngene-cards.c:(.text+0x3381cb): undefined reference to `dvb_pll_attach'
drivers/built-in.o: In function `demod_attach_lg330x':
ngene-cards.c:(.text+0x33828a): undefined reference to `lgdt330x_attach'
drivers/built-in.o: In function `demod_attach_stv0900':
ngene-cards.c:(.text+0x3383d5): undefined reference to `stv090x_attach'
drivers/built-in.o: In function `cineS2_probe':
ngene-cards.c:(.text+0x338b7f): undefined reference to `drxk_attach'
drivers/built-in.o: In function `configure_tda827x_fe':
saa7134-dvb.c:(.text+0x346ae7): undefined reference to `tda10046_attach'
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347283): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x3472cd): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x34731c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34733c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34735c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x347378): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x3473db): undefined reference to `tda10046_attach'
drivers/built-in.o:saa7134-dvb.c:(.text+0x347502): more undefined references to `tda10046_attach' follow
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347812): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x347951): undefined reference to `mt312_attach'
saa7134-dvb.c:(.text+0x3479a9): undefined reference to `mt312_attach'
>> saa7134-dvb.c:(.text+0x3479c1): undefined reference to `zl10039_attach'
This is happening because a builtin module can't use directly a symbol
found on a module. By enabling CONFIG_MEDIA_ATTACH, the configuration
becomes valid, as dvb_attach() macro loads the module if needed, making
the symbol available to the builtin module.
While this bug started to appear after the patches that use IS_DEFINED
macro (like changeset 7b34be71db), this
bug is a way ancient than that.
The thing is that, before the IS_DEFINED() patches, the logic used to be:
&& defined(MODULE))
struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c);
static inline struct dvb_frontend *zl10039_attach(struct dvb_frontend *fe,
u8 i2c_addr,
struct i2c_adapter *i2c)
{
printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
return NULL;
}
The above code, with the .config file used, was evoluting to FALSE
(instead of TRUE as it should be, as CONFIG_DVB_ZL10039 is 'm'),
and were adding the static inline code at saa7134-dvb, instead
of the external call. So, while it weren't producing any compilation
error, the code weren't working either.
So, as the overhead for using CONFIG_MEDIA_ATTACH is minimal, just
enable it, if MODULES is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The r820t_imr() calibration function of the Rafael Micro R820T tuner
generates this error at every tune attempt:
r820t 0-001a: No valid PLL values for 2252021 kHz!
The function was inspired by the original Realtek driver for rtl2832 devices
with the r820t tuner; anyway, in the original code the XTAL frequency of
the tuner was expressed in KHz, while in the kernel driver it is expressed
in Hz; so the calibration failed because of an out-of-range initial value.
The final result of the computation is then passed to the r820t_set_mux()
and r820t_set_pll() functions, but the conversion from KHz to Hz is already
correctly implemented.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The memcpy in shadow_store() could exceed buffer limits when r > 0.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fe->tuner_priv and fe->ops.tuner_ops are initialized twice in r820t_attach().
Remove the redundant initializations and also move fe->ops.tuner_ops
initialization outside of the mutex lock (as in the xc4000 tuner code for example).
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the driver complains about the pre_detect var:
drivers/media/tuners/r820t.c: In function 'r820t_sysfreq_sel':
drivers/media/tuners/r820t.c:722:31: warning: variable 'pre_dect' set but not used [-Wunused-but-set-variable]
While rtl8232 code comments it, perhaps some other driver may use.
So, the better is to keep the code there, allowing to enable it
via r820t config data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/r820t.c: In function 'r820t_imr':
drivers/media/tuners/r820t.c:1871:8: warning: 'n_ring' may be used uninitialized in this function [-Wmaybe-uninitialized]
Mauro: This is a FALSE POSITIVE: the loop will always return a value
for n_ring, as the last test will fill it with 15, if the loop fails.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've moved the kfree(fe->tuner_priv) one line earlier, otherwise it is
a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test as written is always false. It looks like the intent was to
test that the bit was not set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original Win driver doesn't do; rtl-sdr also disabled that
piece of the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
On field tests, the auto gain routine is not working, nor it is
used by the original driver. Let's comment it for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are a few errors at the PLL calculus, causing the device
to use wrong values.
While here, change the calculus to use 32 bits, as there's no
need for 64 bits there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
r820t_standby() can be called before r820t_init().
If that happens, just do nothing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
The rtl-sdr library disabled IMR callibration. While I'm not sure
yet why, it could be a good idea to add a modprobe parameter here,
to allow to also disable it. There are two rationale behind it:
- It helps to compare USB dumps between rtl-sdr and the Kernel module;
- If rtl-sdr disabled it, perhaps there's a good reason (e. g. it
might not be actually working, or it might be causing some trouble).
For both cases, it seems useful to add a modprobe parameter to allow
testing the device with both configurations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Add the code to set the GPIO for this tuner. This code is
currently unused, so it is kept there only for completeness.
With this patch there are just two things that got left from
the original driver:
- At standby, there's another mode, not used by rtl2832u.
Not sure if it might be needed in the future, but I suspect
it is not used at all;
- There is a "fast tune" mode. As nor DVB or V4L API supports
it, it seems an overkill to implement it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This code seems to calibrate I/Q phase and gain during the
device initialization.
This is done only once, and it doesn't seem to be needed to
happen after resuming.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
The rtl-sdr library, from where this driver was initially
based, doesn't use half PLL clock, but this is used on
the Realtek Kernel driver. So, also do the same here.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Instead of using msleep(), use sleep_range(), as it provides
a closer sleep time.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Just cosmetic changes: all other functions are prefixed
by r820t. Do the same for r820t_read().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
As we'll need to retrieve cached registers, make this
function explicit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
If signal is zero, shows it as a zero, not as 0xff.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This is part of the original driver, and adding it doesn't hurt,
so add it, to better sync the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
As the driver's logic uses the bit-reversed order for read,
use it as well when displaying the debug messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
The Realtek Kernel driver uses the second DVB-T 7MHz table instead
of the first one. Use it as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
IF is set at r820t_set_tv_standard(). So, we can't calculate
LO frequency before calling it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Scale used at get_if_freq and LO freq calculus is Hz.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
As this tuner can be used by analog and digital parts of the
driver, be sure that all ops that access the hardware will
be be properly locked.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This tuner works with 2 modes: automatic gain mode and manual
gain mode. Put it into automatic mode, as we currently don't
have any API for manual gain adjustment.
The logic to allow setting the manual mode is there, as it is
just a few extra code. This way, if/when we latter add support
for setting the gain mode, the code is already there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Instead of a binary signal strength measure, use the tuner gain
to obtain a better estimation of the signal strength.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This driver was written from scratch, based on an existing driver
that it is part of rtl-sdr git tree, released under GPLv2:
https://groups.google.com/forum/#!topic/ultra-cheap-sdr/Y3rBEOFtHughttps://github.com/n1gp/gr-bazhttp://cgit.osmocom.org/rtl-sdr/plain/src/tuner_r820t.c
(there are also other variants of it out there)
>From what I understood from the threads, the original driver was converted
to userspace from a Realtek tree. I couldn't find the original tree.
However, the original driver look awkward on my eyes. So, I decided to
write a new version from it from the scratch, while trying to reproduce
everything found there.
TODO:
- After locking, the original driver seems to have some routines to
improve reception. This was not implemented here yet.
- RF Gain set/get is not implemented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are three drivers with *it913x name on it, and they all
belong to the same device:
a tuner, at it913x.c;
a frontend: it913x-fe.c;
a bridge: it913x.c, renamed to dvb_usb_it913x by the
building system.
This is confusing. Even more confusing are the two .c files with
the same name under different directories, with different contents
and different functions. So, prepend the tuner one.
This also breaks the out-of-tree compilation system.
Reported-by: Frederic Fays <frederic.fays@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_rf_strength op in tuner-simple is valid only for the radio mode.
But due to the way get_signal in analog_demod_ops was designed it would
overwrite the signal value with a bogus value when in TV mode.
Pass a pointer to the signal value instead, and when not in radio mode
leave it alone in the tuner-simple.
This broke in commit 030755bde4
(tuner-core: call has_signal for both TV and radio) in kernel 3.6. Before
that this was working correctly. That commit did the right thing, but what
wasn't realized at the time was that tuner-simple should have been updated
as well to restrict setting the signal strength to the radio mode only.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_afc op in tda9887 is valid only for the radio mode.
But due to the way get_afc in analog_demod_ops was designed it would
overwrite the afc value with a bogus value when in TV mode.
Pass a pointer to the afc value instead, and when not in radio mode
leave it alone in the tda9887.
This broke a long time ago in 2.6.19 when the get_afc op was introduced.
Before that the afc was only set for radio mode in the tda9887.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use enum instead of magic values for LNA config in tda8290.
Update tda827x, tda18271 and saa7134 to use the enum too.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow specifying a custom std_map for tda18271 by external configuration.
This is required by cards that require custom std_map for analog TV or radio,
like AverMedia A706.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow disabling I2C gate handling by external configuration.
This is required by cards that have all devices on a single I2C bus,
like AverMedia A706.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for three Sony BTF tuners:
TUNER_SONY_BTF_PG472Z: PAL+SECAM
TUNER_SONY_BTF_PK467Z: NTSC-M-JP
TUNER_SONY_BTF_PB463Z: NTSC-M
These come from the go7007 staging driver where they were implemented in
the wis-sony-tuner i2c driver.
Adding support for these tuners to tuner-types.c is the first step towards
removing the wis-sony-tuner driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That register is property of demodulator so move it correct place.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are demodulator init tables according to used tuner tuner
config. af9033 demod driver does those inits currently and due
to that these duplicate inits could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are demod inits and are already done by af9033 demod driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't need it. Tuner ID and device address are enough.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Copy forgotten power up registers from it913x-fe driver.
Remove two demod registers as those are already written
by af9033 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge those functions to one and disable sleep.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is tuner driver for tuner integrated to the ITE IT9135 and
IT9137 chips. I split it out from the current it913x-fe driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found very small bug in xc5000 source. When set option debug=1 and
listen a radio we see in dmesg xc5000: xc_SetTVStandard()
Standard = M/N-NTSC/PAL-BTSC at all times. However, it should be, instead
"FM Radio-INPUT1_MONO".
That happens because xc5000_set_radio_freq() gets the correct value for
VideoMode and AudioMode for radio and calls xc_SetTVStandard() where name
of standard comes from the incorrect place priv->video_standard.
This incorrect debug message makes debugging a little difficult.
Signed-off-by: Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit a92591a711.
From: Michael Büsch <m@bues.ch>
To: linux-media@vger.kernel.org
Cc: mchehab@redhat.com
Subject: Re: [git:v4l-dvb/for_v3.9] [media] fc0011: Return early, if the frequency is already tuned
Date: Mon, 11 Feb 2013 21:59:19 +0100
Can you please revert this one again? It might cause issues if the dvb device
is reset/reinitialized.
Requested-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some sanity checks to the calculations and make the REG_16 register write consistent
with the other ones.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch was applied by mistake. Michael thinks that it
it needs more work than simply moving the soft reset.
So, it should be held back for further review.
This reverts commit 0a3237704d.
Requested by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Assign the maximum instead of masking with the maximum on value overflow.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch move the soft reset to the attach function because with dual
tuners, when one tuner do reset, the other one is perturbed, and the
stream has errors.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
#if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a missing break so we use XC_RF_MODE_CABLE instead of
XC_RF_MODE_AIR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to keep dummy sleep() callback implementation as
DVB-core checks existence of it before calls callback. Due to that
we can remove it.
FC0012 is based of direct-conversion receiver architecture
(aka Zero-IF) where is no IF used. Due to that IF is always 0 Hz.
Fix comment to point that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to copy config to the driver state. Those are coming from
the const struct and could be used directly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need feed clock to slave demodulator at the very beginning
in case of dual tuner configuration.
I am not sure if that configuration changes clock output divider
or enable clock output itself...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need even more configuration options and overloading dvb_attach()
for all those sounds quite stupid. Due to that switch struct and make
room for new options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commits e666a44fa3 ("[media] tda18212:
silence compiler warning") and e0e52d4e9f
("[media] tda18218: silence compiler warning") silenced warnings
equivalent to these:
drivers/media/tuners/tda18212.c: In function ‘tda18212_attach’:
drivers/media/tuners/tda18212.c:299:2: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/tda18218.c: In function ‘tda18218_attach’:
drivers/media/tuners/tda18218.c:305:2: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
But in both cases 'val' will still be used uninitialized if the calls
of tda18212_rd_reg() or tda18218_rd_reg() fail. Fix this by only
printing the "chip id" if the calls of those functions were successful.
This allows to drop the uninitialized_var() stopgap measure.
Also stop printing the return values of tda18212_rd_reg() or
tda18218_rd_reg(), as these are not interesting.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was a bad idea, as comment also says, to write some "don't care"
registers as 0xff value. Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/xc4000.c: In function ‘check_firmware’:
drivers/media/tuners/xc4000.c:1048:45: warning: ‘fw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1048:39: warning: ‘fw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:39: warning: ‘hw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:33: warning: ‘hw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/tua9001.c:211:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda18271 datasheet says:
"The image rejection calibration and RF tracking filter
calibration must be launched exactly as described in the
flowchart, otherwise bad calibration or even blocking of the
TDA18211HD can result making it impossible to communicate
via the I2C-bus."
(yeah, tda18271 refers there to tda18211 - likely a typo at their
datasheets)
That likely explains why sometimes tda18271 stops answering. That
is now happening more often on designs with drx-k chips, as the
firmware is now loaded asyncrousnly there.
While the above text doesn't explicitly tell that the I2C bus
couldn't be used by other devices during such initialization,
that seems to be a requirement there.
So, let's explicitly use the I2C lock there, avoiding I2C bus
share during those critical moments.
Compile-tested only. Please test.
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a series of warnings when compiled with W=1:
drivers/media/tuners/mt2063.c: In function 'mt2063_setreg':
drivers/media/tuners/mt2063.c:290:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
...
drivers/media/tuners/mt2063.c:2013:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/tuners/mt2063.c:2271:14: warning: no previous prototype for 'tuner_MT2063_SoftwareShutdown' [-Wmissing-prototypes]
drivers/media/tuners/mt2063.c:2286:14: warning: no previous prototype for 'tuner_MT2063_ClearPowerMaskBits' [-Wmissing-prototypes]
Several of those warnings are real bugs: the error status code
used to be unsigned, but they're assigned to negative error
codes.
Fix it by using unsigned int.
While here, comment the two power management functions, while we
don't add a code there to properly handle tuner suspend/resume.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now, if there is a read error in tda18271_get_id, the driver
reports "Unknown device..." Instead, check the return value of
tda18271_read_regs and display the appropriate error message.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
if the configuration option 'delay_cal' is set, delay both IR & RF
calibration until init() is called.
both module option 'cal' or configuration option 'rf_cal_on_startup'
will override this delay. it makes no sense to mix 'delay_cal' with
'rf_cal_on_startup' as these options conflict with each other.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that unnecessary features are powered down at the end of the
attach() function on attach of the tuner's first instance. If the
configuration requires the loop thru or xtout features, they will
remain enabled.
This must *only* be done after attaching the first instance of the tuner.
If there are multiple instances of the tuner, the bridge driver will need
to maintain power managament by itself.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that unnecessary features are powered down at the end of the
attach() function. If the configuration requires the loop thru or
xtout features, they will remain enabled.
Thanks to Antti Palosaari for noticing the additional power consumption.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warnings on a 32 bit system with GCC 4.4.3 and kernel Ubuntu 2.6.32-43 32 bit:
WARNING: "__udivdi3" [fc2580.ko] undefined!
WARNING: "__umoddi3" [fc2580.ko] undefined!
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fc2580.c: In function 'fc2580_set_params':
fc2580.c:118: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fc2580.c: In function 'fc2580_set_params':
fc2580.c:150: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable RXEN and enable RESETN pins on attach to ensure chip is
totally powered down after attach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of old drivers still had the experimental tag. Time to remove it.
It concerns the following drivers:
VIDEO_TLV320AIC23B
USB_STKWEBCAM
VIDEO_CX18
VIDEO_CX18_ALSA
VIDEO_ZORAN_AVS6EYES
DVB_USB_AF9005
MEDIA_TUNER_TEA5761
VIDEO_NOON010PC30
This decision was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
