as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget/function drivers might want to do
improper request recycling by allocating a single
request from one particular endpoint and queueing
it to another completely unrelated endpoint.
One such case was found with f_loopback.c.
To prevent such cases from happening again, let's
WARN() so we get a loud enough failure and persuade
users to report errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>
whenever we get a Disconnect Interrupt, we should
make sure to update out udc state to NOT_ATTACHED,
otherwise sysfs will show wrong values.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabling the core interrupts in complete is too late for
XHCI, and stops it from proper operation. The root of the
problem is due to a disagreement between dwc3-omap and XHCI
about when IRQs should be enabled.
As it turns out, ->resume's documentation states that:
"... generally the driver is expected to start working
again, responding to hardware events and software requests
(the device itself may be left in a low-power state, waiting
for a runtime resume to occur) ..."
From that we infer that IRQs must be unmasked by the end of
->resume().
Due to that, we will remove ->prepare() and ->complete() and
disable/enable interrupts in ->suspend()/->resume().
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3's GUID register is supposed to be used to write
any sort of version we might want. It helps when getting
bug reports for platforms you don't have HW to know
which kernel version of the driver was running on the
platform.
Because we don't really track driver version, but we _do_
track the kernel version, let's write LINUX_VERSION_CODE to
that register and use it for debugging.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 02dae36aa6.
That commit is bogus in two ways:
1) There's no way dwc3-omap's ->suspend() can cause any effect
on xhci's ->suspend(). Linux device driver model guarantees
that a parent's ->suspend() will only be called after all
children are suspended. dwc3-omap is the parent of the
parent of xhci.
2) When implementing Deep Sleep states where context is lost,
USBOTGSS_IRQ0 register, well, looses context so we
_must_ rewrite it otherwise core IRQs will never be
reenabled and USB will appear to be dead.
Fixes: 02dae36 (usb: dwc3: dwc3-omap: Disable/Enable only
wrapper interrupts in prepare/complete)
Cc: <stable@vger.kernel.org> # v3.17
Cc: George Cherian <george.cherian@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).
For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:
"
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: Felipe Balbi <balbi@ti.com>
if our list of requests is empty, return early.
There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The device controller is the same but it has different PCI ID. Add this new
ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of releasing the lock and calling locked
versions of our set_halt() methods, let's hold
the lock all the way through and call unlocked
versions of those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__dwc3_gadget_ep_set_halt() is the function which
handles the actual halt feature. In order to cope
with some extra cleanup comming as a follow-up patch
let's move the isochronous endpoint check there too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 glue layer is hardware layer around Synopsys DesignWare
USB3 core. Its purpose is to supply Synopsys IP with required
clocks, voltages and interface it with the rest of the SoC.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It manages the powerdown signal,
and configures the internal glue logic and syscfg registers.
[ balbi@ti.com : actually switch over to of_platform_depopulate() ]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those functions are only using within debugging
messages, grouping them into debug.h makes sense.
While at that, also add missing multiple inclusion
guard.
Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.
The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.
Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.
Fixes: 2ec2a8be (usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
dep->endpoint.desc is checked at the beginning of
dwc3_gadget_ep_queue(), but after that it may be set to NULL
by another thread and then accessed again in dwc3_gadget_ep_queue().
This will lead to kernel oops.
Expand spinlock protection area to aviod race condition.
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" should be signed. It's only used for zero and negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Move the extcon related code to its own function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move find and set the utmi mode to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move map offset to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the x_major calculation logic from the wrapper revision register
to differentiate between OMAP5 and AM437x. This was done to find the
register offsets of wrapper register. Now that We do it using dt
compatible, remove the whole logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove 'start_new' variable from dwc3_endpoint_transfer_complete(),
since this variable has not been used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.
Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Putting together the code related to getting the 'IORESOURCE_MEM'
and assigning the same to dwc->xhci_resources, for increasing
the readability.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc3 wrapper driver should not be fiddling with the core interrupts.
Disabling the core interrupts in prepare stops xhci from proper operation.
So remove disable/enable of core interrupts from prepare/complete.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In ISOC transfers, when free_slot points to the last TRB (i.e. Link
TRB), and all queued requests meet Missed Interval Isoc error, busy_slot
points to trb0.
busy_slot->trb0
trb1
...
free_slot->trb31(Link TRB)
After end transfer and receiving the XferNotReady event, trb_left is
caculated as 1 which is wrong, and no TRB will be primed to the
endpoint.
The root cause is free_slot is not increased the same way as busy_slot.
When busy_slot is increased by one, it checks if points to a link TRB
after increasement, but free_slot checks it before increasement.
free_slot should behave the same as busy_slot to make the trb_left
caculation correct.
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
This fixes a bug when dwc3_pci_register_phys() fails and leaves device enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
First usage of ret variable will re-write initial value. Thus, there is no need
to initialize it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this makes it slightly easier to read generic CMD
logs. It also helps make sure we're sending proper
parameters for each command.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Facilitate getting required 3.3V and 1.0V VDD supply for
DWC3 controller on Exynos.
With patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
certain perripherals will now need to ensure that,
they request VDD regulators in their drivers, and enable
them so as to make them working.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Glue layers for the DWC3 driver only make sense on specific platforms.
Add dependencies so that they are not built where they aren't needed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move mode (Host, Peripheral, OTG) initialization
to its own function in order to decrease the size
of our probe() routine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
our probe() routine is too large and we can
easily refactor PHY-related code out to another
function to make it slightly less painful to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
so it seems like DWC3 IP doesn't clear stalls
automatically when we disable an endpoint, because
of that, we _must_ make sure stalls are cleared
before clearing the proper bit in DALEPENA register.
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc3_gadget_resize_tx_fifos() iterate only over IN
endpoints that are actually present, based on the
num_in_eps parameter. This terminates the loop so as to
prevent dereferencing a potential NULL dwc->eps[i] where
i >= (num_in_eps + num_out_eps).
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
This patch move simply OF helper function to extcon core and change function
name as following:
- of_extcon_get_extcon_dev() -> extcon_get_edev_by_phandle()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
We know what "value" is and it upsets static checkers that we appear to
have doubts about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These were cut and paste from the ->disconnect function.
Fixes commit 30d577b9bcc4 ('usb: dwc3: gadget: call gadget driver's
->suspend/->resume')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().
However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since PHYs for dwc3 is optional (not all SoCs having PHYs for DWC3
should be programmed), do not return from probe if the USB PHY library
returns -ENODEV as that indicates the platform does not have a
programmable PHY.
While this can be considered as a temporary fix, a long term solution
would be to add 'nop' PHY for platforms that does not have programmable
PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.
Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When going into bus suspend/resume we _must_
call gadget driver's ->suspend/->resume callbacks
accordingly. This patch implements that very feature
which has been missing forever.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's not always we need to force a transfer to be removed
from the core's internal cache. This extra argument will
help differentiating those two cases.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During superspeed, HIRD threshold should always
be zero. Curent driver wasn't making sure that
was the case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we have hibernation configured, Databook
instructs us to set KEEP_CONNECT bit together
with RUN_STOP bit, in step 9 of section 12.3.6.1
Initialization for Hibernation Support.
Signed-off-by: Felipe Balbi <balbi@ti.com>
