Check in fdb_add_entry() if the source port should learn, similar
check is used in br_fdb_update.
Note that new fdb entries which are added manually or
as local ones are still permitted.
This patch has been tested by running traffic via a bridge port and
switching the port's state, also by manually adding/removing entries
from the bridge's fdb.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network managers like netifd (used in OpenWRT for instance) try to
configure interface options after creation but before setting the
interface up.
Unfortunately the sysfs / bridge currently only allows to configure the
hash_max and multicast_router options when the bridge interface is up.
But since br_multicast_init() doesn't start any timers and only sets
default values and initializes timers it should be save to reconfigure
the default values after that, before things actually get active after
the bridge is set up.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b672 ("bridge br_multicast: IPv6 MLD support.")
Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c055d5b03b.
There are two issues:
'dnat_took_place' made me think that this is related to
-j DNAT/MASQUERADE.
But thats only one part of the story. This is also relevant for SNAT
when we undo snat translation in reverse/reply direction.
Furthermore, I originally wanted to do this mainly to avoid
storing ipv6 addresses once we make DNAT/REDIRECT work
for ipv6 on bridges.
However, I forgot about SNPT/DNPT which is stateless.
So we can't escape storing address for ipv6 anyway. Might as
well do it for ipv4 too.
Reported-and-tested-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After improving setsockopt() coverage in trinity, I started triggering
vmalloc failures pretty reliably from this code path:
warn_alloc_failed+0xe9/0x140
__vmalloc_node_range+0x1be/0x270
vzalloc+0x4b/0x50
__do_replace+0x52/0x260 [ip_tables]
do_ipt_set_ctl+0x15d/0x1d0 [ip_tables]
nf_setsockopt+0x65/0x90
ip_setsockopt+0x61/0xa0
raw_setsockopt+0x16/0x60
sock_common_setsockopt+0x14/0x20
SyS_setsockopt+0x71/0xd0
It turns out we don't validate that the num_counters field in the
struct we pass in from userspace is initialized.
The same problem also exists in ebtables, arptables, ipv6, and the
compat variants.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When bridge netfilter re-fragments an IP packet for output, all
packets that can not be re-fragmented to their original input size
should be silently discarded.
However, current bridge netfilter output path generates an ICMP packet
with 'size exceeded MTU' message for such packets, this is a bug.
This patch refactors the ip_fragment() API to allow two separate
use cases. The bridge netfilter user case will not
send ICMP, the routing output will, as before.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. Briefly
speaking, cleanups and minor fixes for ipset from Jozsef Kadlecsik and
Serget Popovich, more incremental updates to make br_netfilter a better
place from Florian Westphal, ARP support to the x_tables mark match /
target from and context Zhang Chunyu and the addition of context to know
that the x_tables runs through nft_compat. More specifically, they are:
1) Fix sparse warning in ipset/ip_set_hash_ipmark.c when fetching the
IPSET_ATTR_MARK netlink attribute, from Jozsef Kadlecsik.
2) Rename STREQ macro to STRNCMP in ipset, also from Jozsef.
3) Use skb->network_header to calculate the transport offset in
ip_set_get_ip{4,6}_port(). From Alexander Drozdov.
4) Reduce memory consumption per element due to size miscalculation,
this patch and follow up patches from Sergey Popovich.
5) Expand nomatch field from 1 bit to 8 bits to allow to simplify
mtype_data_reset_flags(), also from Sergey.
6) Small clean for ipset macro trickery.
7) Fix error reporting when both ip_set_get_hostipaddr4() and
ip_set_get_extensions() from per-set uadt functions.
8) Simplify IPSET_ATTR_PORT netlink attribute validation.
9) Introduce HOST_MASK instead of hardcoded 32 in ipset.
10) Return true/false instead of 0/1 in functions that return boolean
in the ipset code.
11) Validate maximum length of the IPSET_ATTR_COMMENT netlink attribute.
12) Allow to dereference from ext_*() ipset macros.
13) Get rid of incorrect definitions of HKEY_DATALEN.
14) Include linux/netfilter/ipset/ip_set.h in the x_tables set match.
15) Reduce nf_bridge_info size in br_netfilter, from Florian Westphal.
16) Release nf_bridge_info after POSTROUTING since this is only needed
from the physdev match, also from Florian.
17) Reduce size of ipset code by deinlining ip_set_put_extensions(),
from Denys Vlasenko.
18) Oneliner to add ARP support to the x_tables mark match/target, from
Zhang Chunyu.
19) Add context to know if the x_tables extension runs from nft_compat,
to address minor problems with three existing extensions.
20) Correct return value in several seqfile *_show() functions in the
netfilter tree, from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have four xtables extensions that cannot be used from the
xt over nft compat layer. The problem is that they need real access to
the full blown xt_entry to validate that the rule comes with the right
dependencies. This check was introduced to overcome the lack of
sufficient userspace dependency validation in iptables.
To resolve this problem, this patch introduces a new field to the
xt_tgchk_param structure that tell us if the extension is run from
nft_compat context.
The three affected extensions are:
1) CLUSTERIP, this target has been superseded by xt_cluster. So just
bail out by returning -EINVAL.
2) TCPMSS. Relax the checking when used from nft_compat. If used with
the wrong configuration, it will corrupt !syn packets by adding TCP
MSS option.
3) ebt_stp. Relax the check to make sure it uses the reserved
destination MAC address for STP.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
nf_bridge information is only needed for -m physdev, so we can always free
it after POST_ROUTING. This has the advantage that allocation and free will
typically happen on the same cpu.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The neigh_header is only needed when we detect DNAT after prerouting
and neigh cache didn't have a mac address for us.
The output port has not been chosen yet so we can re-use the storage
area, bringing struct size down to 32 bytes on x86_64.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Older gcc versions (e.g. gcc version 4.4.6) don't like anonymous unions
which was causing build issues on the newly added switchdev attr/obj
structs. Fix this by using named union on structs.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is revert of:
commit 68e331c785 ("bridge: offload bridge port attributes to switch asic
if feature flag set")
Restore br_dellink back to original and don't call into SELF port driver.
rtnetlink.c:bridge_dellink() already does a call into port driver for SELF.
bridge vlan add/del cmd defaults to MASTER. From man page for bridge vlan
add/del cmd:
self the vlan is configured on the specified physical device.
Required if the device is the bridge device.
master the vlan is configured on the software bridge (default).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is revert of:
commit 68e331c785 ("bridge: offload bridge port attributes to switch asic
if feature flag set")
Restore br_setlink back to original and don't call into SELF port driver.
rtnetlink.c:bridge_setlink() already does a call into port driver for SELF.
bridge set link cmd defaults to MASTER. From man page for bridge link set
cmd:
self link setting is configured on specified physical device
master link setting is configured on the software bridge (default)
The link setting has two values: the device-side value and the software
bridge-side value. These are independent and settable using the bridge
link set cmd by specifying some combination of [master] | [self].
Furthermore, the device-side and bridge-side settings have their own
initial value, viewable from bridge -d link show cmd.
Restoring br_setlink back to original makes rocker (the only in-kernel user
of SELF link settings) work as first implement: two-sided values.
It's true that when both MASTER and SELF are specified from the command,
two netlink notifications are generated, one for each side of the settings.
The user-space app can distiquish between the two notifications by
observing the MASTER or SELF flag.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP update is just a settable port attribute, so convert
switchdev_port_stp_update to an attr set.
For DSA, the prepare phase is skipped and STP updates are only done in the
commit phase. This is because currently the DSA drivers don't need to
allocate any memory for STP updates and the STP update will not fail to HW
(unless something horrible goes wrong on the MDIO bus, in which case the
prepare phase wouldn't have been able to predict anyway).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use these new, neat helpers.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 37a393bc49 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper functions to parse and dump register values in netlink attributes.
These helpers will later be changed to take care of translation between the
old 128 bit and the new 32 bit register numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simple conversion to use u32 pointers to the beginning of the registers
to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All users of nft_validate_register_store() first invoke
nft_validate_output_register(). There is in fact no use for using it
on its own, so simplify the code by folding the functionality into
nft_validate_register_store() and kill it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The existing name is ambiguous, data is loaded as well when we read from
a register. Rename to nft_validate_register_store() for clarity and
consistency with the upcoming patch to introduce its counterpart,
nft_validate_register_load().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For values spanning multiple registers, we need to validate that enough
space is available from the destination register onwards. Add a len
argument to nft_validate_data_load() and consolidate the existing length
validations in preparation of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_bridge_info->mask is used for several things, for example to
remember if skb->pkt_type was set to OTHER_HOST.
For a bridge, OTHER_HOST is expected case. For ip forward its a non-starter
though -- routing expects PACKET_HOST.
Bridge netfilter thus changes OTHER_HOST to PACKET_HOST before hook
invocation and then un-does it after hook traversal.
This information is irrelevant outside of br_netfilter.
After this change, ->mask now only contains flags that need to be
known outside of br_netfilter in fast-path.
Future patch changes mask into a 2bit state field in sk_buff, so that
we can remove skb->nf_bridge pointer for good and consider all remaining
places that access nf_bridge info content a not-so fastpath.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
->mask is a bit info field that mixes various use cases.
In particular, we have flags that are mutually exlusive, and flags that
are only used within br_netfilter while others need to be exposed to
other parts of the kernel.
Remove BRNF_8021Q/PPPoE flags. They're mutually exclusive and only
needed within br_netfilter context.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't access skb->nf_bridge directly, this pointer will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_netfilter maintains an extra state, nf_bridge_info, which is attached
to skb via skb->nf_bridge pointer.
Amongst other things we use skb->nf_bridge->data to store the original
mac header for every processed skb.
This is required for ip refragmentation when using conntrack
on top of bridge, because ip_fragment doesn't copy it from original skb.
However there is no need anymore to do this unconditionally.
Move this to the one place where its needed -- when br_netfilter calls
ip_fragment().
Also switch to percpu storage for this so we can handle fragmenting
without accessing nf_bridge meta data.
Only user left is neigh resolution when DNAT is detected, to hold
the original source mac address (neigh resolution builds new mac header
using bridge mac), so rename ->data and reduce its size to whats needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We also need to save/store in forward, else br_parse_ip_options call
will zero frag_max_size as well.
Fixes: 93fdd47e5 ('bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING')
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next.
Basically, more incremental updates for br_netfilter from Florian
Westphal, small nf_tables updates (including one fix for rb-tree
locking) and small two-liner to add extra validation for the REJECT6
target.
More specifically, they are:
1) Use the conntrack status flags from br_netfilter to know that DNAT is
happening. Patch for Florian Westphal.
2) nf_bridge->physoutdev == NULL already indicates that the traffic is
bridged, so let's get rid of the BRNF_BRIDGED flag. Also from Florian.
3) Another patch to prepare voidization of seq_printf/seq_puts/seq_putc,
from Joe Perches.
4) Consolidation of nf_tables_newtable() error path.
5) Kill nf_bridge_pad used by br_netfilter from ip_fragment(),
from Florian Westphal.
6) Access rb-tree root node inside the lock and remove unnecessary
locking from the get path (we already hold nfnl_lock there), from
Patrick McHardy.
7) You cannot use a NFT_SET_ELEM_INTERVAL_END when the set doesn't
support interval, also from Patrick.
8) Enforce IP6T_F_PROTO from ip6t_REJECT to make sure the core is
actually restricting matches to TCP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_netfilter frag output function calls skb_cow_head() so in
case it needs a larger headroom to e.g. re-add a previously stripped PPPOE
or VLAN header things will still work (at cost of reallocation).
We can then move nf_bridge_encap_header_len to br_netfilter.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Its not needed anymore since 2bf540b73e
([NETFILTER]: bridge-netfilter: remove deferred hooks).
Before this it was possible to have physoutdev set for locally generated
packets -- this isn't the case anymore:
BRNF_STATE_BRIDGED flag is set when we assign nf_bridge->physoutdev,
so physoutdev != NULL means BRNF_STATE_BRIDGED is set.
If physoutdev is NULL, then we are looking at locally-delivered and
routed packet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ask conntrack instead of storing ipv4 address in nf_bridge_info->data.
Ths avoids the need to use ->data during NF_PRE_ROUTING.
Only two functions that need ->data remain.
These will be addressed in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On adding an interface br_add_if() sets the MTU to the min of
all the interfaces. Do the same thing on removing an interface too
in br_del_if.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e5de75b ("netfilter: bridge: move DNAT helper to br_netfilter") results
in the following link problem:
net/bridge/br_device.c:29: undefined reference to `br_nf_prerouting_finish_bridge`
Moreover it creates a hard dependency between br_netfilter and the
bridge core, which is what we've been trying to avoid so far.
Resolve this problem by using a hook structure so we reduce #ifdef
pollution and keep bridge netfilter specific code under br_netfilter.c
which was the original intention.
Reported-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
