To speed up the Simple Pairing connection setup, the support for the
default link policy has been enabled. This is in contrast to settings
the link policy on every connection setup. Using the default link policy
is the preferred way since there is no need to dynamically change it for
every connection.
For backward compatibility reason and to support old userspace the
HCISETLINKPOL ioctl has been switched over to using hci_request() to
issue the HCI command for setting the default link policy instead of
just storing it in the HCI device structure.
However the hci_request() can only be issued when the device is
brought up. If used on a device that is registered, but still down
it will timeout and fail. This is problematic since the command is
put on the TX queue and the Bluetooth core tries to submit it to
hardware that is not ready yet. The timeout for these requests is
10 seconds and this causes a significant regression when setting up
a new device.
The userspace can perfectly handle a failure of the HCISETLINKPOL
ioctl and will re-submit it later, but the 10 seconds delay causes
a problem. So in case hci_request() is called on a device that is
still down, just fail it with ENETDOWN to indicate what happens.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes kernel bugzilla 11469: "TUN with 1024 neighbours:
ip6_dst_lookup_tail NULL crash"
dst->neighbour is not necessarily hooked up at this point
in the processing path, so blindly dereferencing it is
the wrong thing to do. This NULL check exists in other
similar paths and this case was just an oversight.
Also fix the completely wrong and confusing indentation
here while we're at it.
Based upon a patch by Evgeniy Polyakov.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit commit 4c563f7669 ("[XFRM]:
Speed up xfrm_policy and xfrm_state walking") inadvertently removed
larval states and socket policies from netlink dumps. This patch
restores them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Security Mode 4 of the Bluetooth 2.1 specification has strict
authentication and encryption requirements. It is the initiators job
to create a secure ACL link. However in case of malicious devices, the
acceptor has to make sure that the ACL is encrypted before allowing
any kind of L2CAP connection. The only exception here is the PSM 1 for
the service discovery protocol, because that is allowed to run on an
insecure ACL link.
Previously it was enough to reject a L2CAP connection during the
connection setup phase, but with Bluetooth 2.1 it is forbidden to
do any L2CAP protocol exchange on an insecure link (except SDP).
The new hci_conn_check_link_mode() function can be used to check the
integrity of an ACL link. This functions also takes care of the cases
where Security Mode 4 is disabled or one of the devices is based on
an older specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the introduction of Security Mode 4 and Simple Pairing from the
Bluetooth 2.1 specification it became mandatory that the initiator
requires authentication and encryption before any L2CAP channel can
be established. The only exception here is PSM 1 for the service
discovery protocol (SDP). It is meant to be used without any encryption
since it contains only public information. This is how Bluetooth 2.0
and before handle connections on PSM 1.
For Bluetooth 2.1 devices the pairing procedure differentiates between
no bonding, general bonding and dedicated bonding. The L2CAP layer
wrongly uses always general bonding when creating new connections, but it
should not do this for SDP connections. In this case the authentication
requirement should be no bonding and the just-works model should be used,
but in case of non-SDP connection it is required to use general bonding.
If the new connection requires man-in-the-middle (MITM) protection, it
also first wrongly creates an unauthenticated link key and then later on
requests an upgrade to an authenticated link key to provide full MITM
protection. With Simple Pairing the link key generation is an expensive
operation (compared to Bluetooth 2.0 and before) and doing this twice
during a connection setup causes a noticeable delay when establishing
a new connection. This should be avoided to not regress from the expected
Bluetooth 2.0 connection times. The authentication requirements are known
up-front and so enforce them.
To fulfill these requirements the hci_connect() function has been extended
with an authentication requirement parameter that will be stored inside
the connection information and can be retrieved by userspace at any
time. This allows the correct IO capabilities exchange and results in
the expected behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ACL config stage keeps holding a reference count on incoming
connections when requesting the extended features. This results in
keeping an ACL link up without any users. The problem here is that
the Bluetooth specification doesn't define an ownership of the ACL
link and thus it can happen that the implementation on the initiator
side doesn't care about disconnecting unused links. In this case the
acceptor needs to take care of this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bridge: don't allow setting hello time to zero
netns : fix kernel panic in timewait socket destruction
pkt_sched: Fix qdisc state in net_tx_action()
netfilter: nf_conntrack_irc: make sure string is terminated before calling simple_strtoul
netfilter: nf_conntrack_gre: nf_ct_gre_keymap_flush() fixlet
netfilter: nf_conntrack_gre: more locking around keymap list
netfilter: nf_conntrack_sip: de-static helper pointers
Dushan Tcholich reports that on his system ksoftirqd can consume
between %6 to %10 of cpu time, and cause ~200 context switches per
second.
He then correlated this with a report by bdupree@techfinesse.com:
http://marc.info/?l=linux-kernel&m=119613299024398&w=2
and the culprit cause seems to be starting the bridge interface.
In particular, when starting the bridge interface, his scripts
are specifying a hello timer interval of "0".
The bridge hello time can't be safely set to values less than 1
second, otherwise it is possible to end up with a runaway timer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
How to reproduce ?
- create a network namespace
- use tcp protocol and get timewait socket
- exit the network namespace
- after a moment (when the timewait socket is destroyed), the kernel
panics.
# BUG: unable to handle kernel NULL pointer dereference at
0000000000000007
IP: [<ffffffff821e394d>] inet_twdr_do_twkill_work+0x6e/0xb8
PGD 119985067 PUD 11c5c0067 PMD 0
Oops: 0000 [1] SMP
CPU 1
Modules linked in: ipv6 button battery ac loop dm_mod tg3 libphy ext3 jbd
edd fan thermal processor thermal_sys sg sata_svw libata dock serverworks
sd_mod scsi_mod ide_disk ide_core [last unloaded: freq_table]
Pid: 0, comm: swapper Not tainted 2.6.27-rc2 #3
RIP: 0010:[<ffffffff821e394d>] [<ffffffff821e394d>]
inet_twdr_do_twkill_work+0x6e/0xb8
RSP: 0018:ffff88011ff7fed0 EFLAGS: 00010246
RAX: ffffffffffffffff RBX: ffffffff82339420 RCX: ffff88011ff7ff30
RDX: 0000000000000001 RSI: ffff88011a4d03c0 RDI: ffff88011ac2fc00
RBP: ffffffff823392e0 R08: 0000000000000000 R09: ffff88002802a200
R10: ffff8800a5c4b000 R11: ffffffff823e4080 R12: ffff88011ac2fc00
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000000
FS: 0000000041cbd940(0000) GS:ffff8800bff839c0(0000)
knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000007 CR3: 00000000bd87c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff8800bff9e000, task
ffff88011ff76690)
Stack: ffffffff823392e0 0000000000000100 ffffffff821e3a3a
0000000000000008
0000000000000000 ffffffff821e3a61 ffff8800bff7c000 ffffffff8203c7e7
ffff88011ff7ff10 ffff88011ff7ff10 0000000000000021 ffffffff82351108
Call Trace:
<IRQ> [<ffffffff821e3a3a>] ? inet_twdr_hangman+0x0/0x9e
[<ffffffff821e3a61>] ? inet_twdr_hangman+0x27/0x9e
[<ffffffff8203c7e7>] ? run_timer_softirq+0x12c/0x193
[<ffffffff820390d1>] ? __do_softirq+0x5e/0xcd
[<ffffffff8200d08c>] ? call_softirq+0x1c/0x28
[<ffffffff8200e611>] ? do_softirq+0x2c/0x68
[<ffffffff8201a055>] ? smp_apic_timer_interrupt+0x8e/0xa9
[<ffffffff8200cad6>] ? apic_timer_interrupt+0x66/0x70
<EOI> [<ffffffff82011f4c>] ? default_idle+0x27/0x3b
[<ffffffff8200abbd>] ? cpu_idle+0x5f/0x7d
Code: e8 01 00 00 4c 89 e7 41 ff c5 e8 8d fd ff ff 49 8b 44 24 38 4c 89 e7
65 8b 14 25 24 00 00 00 89 d2 48 8b 80 e8 00 00 00 48 f7 d0 <48> 8b 04 d0
48 ff 40 58 e8 fc fc ff ff 48 89 df e8 c0 5f 04 00
RIP [<ffffffff821e394d>] inet_twdr_do_twkill_work+0x6e/0xb8
RSP <ffff88011ff7fed0>
CR2: 0000000000000007
This patch provides a function to purge all timewait sockets related
to a network namespace. The timewait sockets life cycle is not tied with
the network namespace, that means the timewait sockets stay alive while
the network namespace dies. The timewait sockets are for avoiding to
receive a duplicate packet from the network, if the network namespace is
freed, the network stack is removed, so no chance to receive any packets
from the outside world. Furthermore, having a pending destruction timer
on these sockets with a network namespace freed is not safe and will lead
to an oops if the timer callback which try to access data belonging to
the namespace like for example in:
inet_twdr_do_twkill_work
-> NET_INC_STATS_BH(twsk_net(tw), LINUX_MIB_TIMEWAITED);
Purging the timewait sockets at the network namespace destruction will:
1) speed up memory freeing for the namespace
2) fix kernel panic on asynchronous timewait destruction
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_tx_action() can skip __QDISC_STATE_SCHED bit clearing while qdisc
is neither ran nor rescheduled, which may cause endless loop in
dev_deactivate().
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan points out:
1. simple_strtoul() silently accepts all characters for given base even
if result won't fit into unsigned long. This is amazing stupidity in
itself, but
2. nf_conntrack_irc helper use simple_strtoul() for DCC request parsing.
Data first copied into 64KB buffer, so theoretically nothing prevents
reading past the end of it, since data comes from network given 1).
This is not actually a problem currently since we're guaranteed to have
a 0 byte in skb_shared_info or in the buffer the data is copied to, but
to make this more robust, make sure the string is actually terminated.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does "kfree(list_head)" which looks wrong because entity that was
allocated is definitely not list_head.
However, this all works because list_head is first item in
struct nf_ct_gre_keymap.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
gre_keymap_list should be protected in all places.
(unless I'm misreading something)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helper's ->help hook can run concurrently with itself, so iterating over
SIP helpers with static pointer won't work reliably.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 087d833e5a, which was
reported to break wireless at least in some combinations with 32bit user
space and a 64bit kernel. Alex Williamnson bisected it to this commit.
Reported-and-bisected-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
Andrew Morton reported a build failure on sparc32, because TIPC
uses names like "struct node" and there is a like named data
structure defined in linux/node.h
This just regexp replaces "struct node*" to "struct tipc_node*"
to avoid this and any future similar problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipsec: Fix deadlock in xfrm_state management.
ipv: Re-enable IP when MTU > 68
net/xfrm: Use an IS_ERR test rather than a NULL test
ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message.
ath9k: Incorrect key used when group and pairwise ciphers are different.
rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON
mac80211: Fix debugfs union misuse and pointer corruption
wireless/libertas/if_cs.c: fix memory leaks
orinoco: Multicast to the specified addresses
iwlwifi: fix 64bit platform firmware loading
iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE)
iwlwifi: workaround interrupt handling no some platforms
iwlwifi: do not use GFP_DMA in iwl_tx_queue_init
net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS
net: Unbreak userspace usage of linux/mroute.h
pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock()
ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
Ever since commit 4c563f7669
("[XFRM]: Speed up xfrm_policy and xfrm_state walking") it is
illegal to call __xfrm_state_destroy (and thus xfrm_state_put())
with xfrm_state_lock held. If we do, we'll deadlock since we
have the lock already and __xfrm_state_destroy() tries to take
it again.
Fix this by pushing the xfrm_state_put() calls after the lock
is dropped.
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable IP when the MTU gets back to a valid size.
This patch just checks if the in_dev is NULL on a NETDEV_CHANGEMTU event
and if MTU is valid (bigger than 68), then re-enable in_dev.
Also a function that checks valid MTU size was created.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function xfrm_bundle_create returns an ERR
pointer, but never returns a NULL pointer. So a NULL test that comes
after an IS_ERR test should be deleted.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@match_bad_null_test@
expression x, E;
statement S1,S2;
@@
x = xfrm_bundle_create(...)
... when != x = E
* if (x != NULL)
S1 else S2
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current setup with hal and NetworkManager will fail to work
without newest hal version with this config option disabled.
Although this will solve itself by time, at the moment it is
dishonest to say that we don't know any software that uses it,
if there are many many people relying on old hal versions.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-2.6.27' of git://linux-nfs.org/~bfields/linux:
nfsd: fix buffer overrun decoding NFSv4 acl
sunrpc: fix possible overrun on read of /proc/sys/sunrpc/transports
nfsd: fix compound state allocation error handling
svcrdma: Fix race between svc_rdma_recvfrom thread and the dto_tasklet
Vegard Nossum reported
----------------------
> I noticed that something weird is going on with /proc/sys/sunrpc/transports.
> This file is generated in net/sunrpc/sysctl.c, function proc_do_xprt(). When
> I "cat" this file, I get the expected output:
> $ cat /proc/sys/sunrpc/transports
> tcp 1048576
> udp 32768
> But I think that it does not check the length of the buffer supplied by
> userspace to read(). With my original program, I found that the stack was
> being overwritten by the characters above, even when the length given to
> read() was just 1.
David Wagner added (among other things) that copy_to_user could be
probably used here.
Ingo Oeser suggested to use simple_read_from_buffer() here.
The conclusion is that proc_do_xprt doesn't check for userside buffer
size indeed so fix this by using Ingo's suggestion.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
CC: Ingo Oeser <ioe-lkml@rameria.de>
Cc: Neil Brown <neilb@suse.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Greg Banks <gnb@sgi.com>
Cc: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Use qdisc_root_sleeping_lock() instead of qdisc_root_lock() where
appropriate. The only difference is while dev is deactivated, when
currently we can use a sleeping qdisc with the lock of noop_qdisc.
This shouldn't be dangerous since after deactivation root lock could
be used only by gen_estimator code, but looks wrong anyway.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of identifiers needs to be checked against the option
length. Also, the identifier index provided needs to be verified
to make sure that it doesn't exceed the bounds of the array.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonds check to prevent buffer overlflow was not exactly
right. It still allowed overflow of up to 8 bytes which is
sizeof(struct sctp_authkey).
Since optlen is already checked against the size of that struct,
we are guaranteed not to cause interger overflow either.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the TCP header is miscalculated when the window scale ends
up being 0. Additionally, this can be induced by sending a SYN to a
passive open port with a window scale option with value 0.
Signed-off-by: Philip Love <love_phil@emc.com>
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While passing a qdisc root lock to gen_new_estimator() and
gen_replace_estimator() dev could be deactivated or even before
grafting proper root qdisc as qdisc_sleeping (e.g. qdisc_create), so
using qdisc_root_lock() is not enough. This patch adds
qdisc_root_sleeping_lock() for this, plus additional checks, where
necessary.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pointers are RCU protected, so proper primitives should be used.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During dev_graft_qdisc() dev is deactivated, so qdisc_root_lock()
returns wrong lock of noop_qdisc instead of qdisc_sleeping.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The association request includes a list of supported data rates.
802.11b: 4 supported rates.
802.11g: 12 (8 + 4) supported rates.
802.11a: 8 supported rates.
The rates tag of the assoc request has room for only 8 rates. In case of
802.11g an extended rate tag is appended. However in net/wireless/mlme.c
an extended (empty) rate tag is also appended if the number of rates is
exact 8. This empty (length=0) extended rates tag causes some APs to
deny association with code 18 (unsupported rates). These APs include my
ZyXEL G-570U, and according to Tomas Winkler som Cisco APs.
'If count == 8' has been used to check for the need for an extended rates
tag. But count would also be equal to 8 if the for loop exited because of
no more supported rates. Therefore a check for count being less than
rates_len would seem more correct.
Thanks to:
* Dan Williams for newbie guidance
* Tomas Winkler for confirming the problem
Signed-off-by: Jan-Espen Pettersen <sigsegv@radiotube.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous version was using incorrect union structures for non-AP
interfaces when adding and removing max_ratectrl_rateidx and
force_unicast_rateidx entries. Depending on the vif type, this ended
up in corrupting debugfs entries since the dentries inside different
union structures ended up going being on top of eachother.. As the
end result, debugfs files were being left behind with references to
freed data (instant kernel oops on access) and directories were not
removed properly when unloading mac80211 drivers. This patch fixes
those issues by using only a single union structure based on the vif
type.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function mesh_table_grow, it is the new table not the argument table
that should be freed if the function fails (cf commit
bd9b448f4c)
The semantic match that detects this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = mesh_table_alloc@p1(...)
...
if (x == NULL) S
... when != E = x
when != mesh_table_free(x)
goto@p2 l;
... when != E = x
when != f(...,x,...)
when any
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
p3 << r.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s via line %s" % (p1[0].file,p1[0].line,p3[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous code was using IWEVCUSTOM to report IEs from AssocReq and
AssocResp frames into user space. This can easily hit the 256 byte
limit (IW_CUSTOM_MAX) with APs that include number of vendor IEs in
AssocResp. This results in the event message not being sent and dmesg
showing "wlan0 (WE) : Wireless Event too big (366)" type of errors.
Convert mac80211 to use IWEVASSOCREQIE/IWEVASSOCRESPIE to avoid the
issue of being unable to send association IEs as wireless events. These
newer event types use binary encoding and larger maximum size
(IW_GENERIC_IE_MAX = 1024), so the likelyhood of not being able to send
the IEs is much smaller than with IWEVCUSTOM. As an extra benefit, the
code is also quite a bit simpler since there is no need to allocate an
extra buffer for hex encoding.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial patch adding a missing line break on
rfkill_claim_show().
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.co>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Braino: net.ipv6 in ipv6 skeleton has no business in rotable
class
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net.ipv4.neigh should be a part of skeleton to avoid ordering problems
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure used for SCTP_AUTH_KEY option contains a
length that needs to be verfied to prevent buffer overflow
conditions. Spoted by Eugene Teo <eteo@redhat.com>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem spotted with zebra, but not sure if it is
necessary a kernel problem. With IPV6 when an address is added to an
interface, Zebra creates a duplicate RIB entry, one as a connected
route, and other as a kernel route.
When an address is added to an interface the RTN_NEWADDR message
causes Zebra to create a connected route. In IPV4 when an address is
added to an interface a RTN_NEWROUTE message is set to user space with
the protocol RTPROT_KERNEL. Zebra ignores these messages, because it
already has the connected route.
The problem is that route created in IPV6 has route protocol ==
RTPROT_BOOT. Was this a design decision or a bug? This fixes it. Same
patch applies to both net-2.6 and stable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.
With feedback from Herbert Xu and David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_deactivate() can skip rescheduling of a qdisc by qdisc_watchdog()
or other timer calling netif_schedule() after dev_queue_deactivate().
We prevent this checking aliveness before scheduling the timer. Since
during deactivation the root qdisc is available only as qdisc_sleeping
additional accessor qdisc_root_sleeping() is created.
With feedback from Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the SCTP-AUTH socket options could cause a panic
if the extension is disabled and the API is envoked.
Additionally, there were some additional assumptions that
certain pointers would always be valid which may not
always be the case.
This patch hardens the API and address all of the crash
scenarios.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann