The current code only assigns the default cpu_dp to all user ports of
the switch to which the CPU port belongs. The user ports of the other
switches of the fabric thus don't have a default CPU port.
This patch fixes this by assigning the cpu_dp of all user ports of all
switches of the fabric when the tree is fully parsed.
Fixes: a29342e739 ("net: dsa: Associate slave network device with CPU port")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports with DSA, have the
dsa_port structure know which CPU it is associated with. This will be
important in order to make sure the correct CPU is used for transmission
of the frames. If not for functional reasons, for performance (e.g: load
balancing) and forwarding decisions.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.
The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.
To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().
Fixes: 9520ed8fb8 ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was no reason for duplicating the code that initializes
ds->enabled_port_mask in both dsa_parse_ports_dn() and
dsa_parse_ports(), instead move this to dsa_ds_parse() which is early
enough before ops->setup() has run.
While at it, we can now make dsa_is_cpu_port() check ds->cpu_port_mask
which is a step towards being multi-CPU port capable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have all the information we need in dsa_port, so use it instead of
repeating the same arguments over and over again.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to have a reference to a dsa_switch, instead we should
pass a reference to a CPU dsa_port, change that. This is a preliminary
change to better support multiple CPU ports.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_ptr is not a void pointer anymore since Nov 2011, as of cf50dcc24f
("dsa: Change dsa_uses_{dsa, trailer}_tags() into inline functions"),
but an explicit dsa_switch_tree pointer, thus remove the (void *) cast.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The public include/net/dsa.h file is meant for DSA drivers, while all
DSA core files share a common private header net/dsa/dsa_priv.h file.
Ensure that dsa_priv.h is the only DSA core file to include net/dsa.h,
and add a new line to separate absolute and relative headers at the same
time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dsa_switch_tree instance holds a dsa_switch pointer and a port index
to identify the switch port to which the CPU is attached.
Now that the DSA layer has a dsa_port structure to hold this data, use
it to point the switch CPU port.
This patch simply substitutes s/dst->cpu_switch/dst->cpu_dp->ds/ and
s/dst->cpu_port/dst->cpu_dp->index/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_create() can fail, and dsa_user_port_unapply() will properly check
for the network device not being NULL before attempting to destroy it. We were
not setting the slave network device as NULL if dsa_slave_create() failed, so
we would later on be calling dsa_slave_destroy() on a now free'd and
unitialized network device, causing crashes in dsa_slave_destroy().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the physical switch instance and port index a DSA port belongs to to
the dsa_port structure.
That can be used later to retrieve information about a physical port
when configuring a switch fabric, or lighten up struct dsa_slave_priv.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains the number of ports. Use it where the
structure is valid instead of the DSA_MAX_PORTS value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the assignment of ports in _dsa_register_switch() closer to where
it is checked, no functional change. Re-order declarations to be
preserve the inverted christmas tree style.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that these functions take a device_node structure pointer
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new DTS bindings for DSA (dsa2), the "ethernet" and "link"
phandles are respectively mandatory and exclusive to CPU port and DSA
link device tree nodes.
Simplify dsa2.c a bit by checking the presence of such phandle instead
of checking the redundant "label" property.
Then the Linux philosophy for Ethernet switch ports is to expose them to
userspace as standard NICs by default. Thus use the standard enumerated
"eth%d" device name if no "label" property is provided for a user port.
This allows to save DTS files from subjective net device names.
If one wants to rename an interface, udev rules can be used as usual.
Of course the current behavior is unchanged, and the optional "label"
property for user ports has precedence over the enumerated name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly possible to have non zero indexed switches being present
in a DSA switch tree, in such a case, we will be deferencing a NULL
pointer while dsa_cpu_port_ethtool_{setup,restore}. Be more defensive
and ensure that dst->ds[0] is valid before doing anything with it.
Fixes: 0c73c523cf ("net: dsa: Initialize CPU port ethtool ops per tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there can be multiple dsa switches stacked together but
not all of devicetree nodes available at the time of calling
dsa_dst_parse(), EPROBE_DEFER can be returned by it. When this
happens, only the last dsa switch has to be deleted by
dsa_dst_del_ds(), but not the whole list, because next time linux
cames back to this function it will try to add only the last dsa
switch which returned EPROBE_DEFER.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_dsa_register_switch() gets a dsa_switch_tree object either via
dsa_get_dst() or via dsa_add_dst(). Former path does not increase kref
in returned object (resulting into caller not owning a reference),
while later path does create a new object (resulting into caller owning
a reference).
The rest of _dsa_register_switch() assumes that it owns a reference, and
calls dsa_put_dst().
This causes a memory breakage if first switch in the tree initialized
successfully, but second failed to initialize. In particular, freed
dsa_swith_tree object is left referenced by switch that was initialized,
and later access to sysfs attributes of that switch cause OOPS.
To fix, need to add kref_get() call to dsa_get_dst().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 1 of the 3 drivers currently has a set_addr() operation. Make the
set_addr() callback optional to reduce the amount of empty stubs inside
the drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 83c0afaec7 ("net: dsa: Add new binding implementation")
has a duplicate invocation of the set_addr() operation callback. Remove one
of them.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/dsa/dsa2.c:680:6: warning:
symbol '_dsa_unregister_switch' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.
Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.
This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can properly support multiple distinct trees in the system,
using a global variable: dsa_cpu_port_ethtool_ops is getting clobbered
as soon as the second switch tree gets probed, and we don't want that.
We need to move this to be dynamically allocated, and since we can't
really be comparing addresses anymore to determine first time
initialization versus any other times, just move this to dsa.c and
dsa2.c where the remainder of the dst/ds initialization happens.
The operations teardown restores the master netdev's ethtool_ops to its
original ethtool_ops pointer (typically within the Ethernet driver)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mimic what net/dsa/dsa.c does and provide a slave MII bus by default
which will be created if the driver implements a phy_read method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers rely on these two bitmasks to contain the correct values
for them to successfully probe and initialize at drv->setup() time,
calculate correct values to put in both masks as early as possible in
dsa_get_ports_dn().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot