This patch changes the default initial receive window to 10 mss
(defined constant). The default window is limited to the maximum
of 10*1460 and 2*mss (when mss > 1460).
draft-ietf-tcpm-initcwnd-00 is a proposal to the IETF that recommends
increasing TCP's initial congestion window to 10 mss or about 15KB.
Leading up to this proposal were several large-scale live Internet
experiments with an initial congestion window of 10 mss (IW10), where
we showed that the average latency of HTTP responses improved by
approximately 10%. This was accompanied by a slight increase in
retransmission rate (0.5%), most of which is coming from applications
opening multiple simultaneous connections. To understand the extreme
worst case scenarios, and fairness issues (IW10 versus IW3), we further
conducted controlled testbed experiments. We came away finding minimal
negative impact even under low link bandwidths (dial-ups) and small
buffers. These results are extremely encouraging to adopting IW10.
However, an initial congestion window of 10 mss is useless unless a TCP
receiver advertises an initial receive window of at least 10 mss.
Fortunately, in the large-scale Internet experiments we found that most
widely used operating systems advertised large initial receive windows
of 64KB, allowing us to experiment with a wide range of initial
congestion windows. Linux systems were among the few exceptions that
advertised a small receive window of 6KB. The purpose of this patch is
to fix this shortcoming.
References:
1. A comprehensive list of all IW10 references to date.
http://code.google.com/speed/protocols/tcpm-IW10.html
2. Paper describing results from large-scale Internet experiments with IW10.
http://ccr.sigcomm.org/drupal/?q=node/621
3. Controlled testbed experiments under worst case scenarios and a
fairness study.
http://www.ietf.org/proceedings/79/slides/tcpm-0.pdf
4. Raw test data from testbed experiments (Linux senders/receivers)
with initial congestion and receive windows of both 10 mss.
http://research.csc.ncsu.edu/netsrv/?q=content/iw10
5. Internet-Draft. Increasing TCP's Initial Window.
https://datatracker.ietf.org/doc/draft-ietf-tcpm-initcwnd/
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure sysctl_tcp_cookie_size is read once in
tcp_cookie_size_check(), or we might return an illegal value to caller
if sysctl_tcp_cookie_size is changed by another cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: William Allen Simpson <william.allen.simpson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_tso_win_divisor might be set to zero while one cpu runs in
tcp_tso_should_defer(). Make sure we dont allow a divide by zero by
reading sysctl_tcp_tso_win_divisor exactly once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug has to do with boundary checks on the initial receive window.
If the initial receive window falls between init_cwnd and the
receive window specified by the user, the initial window is incorrectly
brought down to init_cwnd. The correct behavior is to allow it to
remain unchanged.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_BASE_MSS is defined, but not used.
commit 5d424d5a introduce this macro, so use
it to initial sysctl_tcp_base_mss.
commit 5d424d5a67
Author: John Heffner <jheffner@psc.edu>
Date: Mon Mar 20 17:53:41 2006 -0800
[TCP]: MTU probing
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_pick_tx, don't do work in calculating queue
index or setting
the index in the sock unless the device has more than one queue. This
allows the sock to be set only with a queue index of a multi-queue
device which is desirable if device are stacked like in a tunnel.
We also allow the mapping of a socket to queue to be changed. To
maintain in order packet transmission a flag (ooo_okay) has been
added to the sk_buff structure. If a transport layer sets this flag
on a packet, the transmit queue can be changed for the socket.
Presumably, the transport would set this if there was no possbility
of creating OOO packets (for instance, there are no packets in flight
for the socket). This patch includes the modification in TCP output
for setting this flag.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tcp_connect code completely ignores errors from sending an skb.
This makes sense in many situations (like -ENOBUFFS) but I want to be able to
immediately fail connections if they are denied by the SELinux netfilter hook.
Netfilter does not normally return ECONNREFUSED when it drops a packet so we
respect that error code as a final and fatal error that can not be recovered.
Based-on-patch-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Ilpo Jarvinen, this updates also the initial window
setting for tcp_output with regard to RFC 5681.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Via setsockopt it is possible to reduce the socket RX buffer
(SO_RCVBUF). TCP method to select the initial window and window scaling
option in tcp_select_initial_window() currently misbehaves and do not
consider a reduced RX socket buffer via setsockopt.
Even though the server's RX buffer is reduced via setsockopt() to 256
byte (Initial Window 384 byte => 256 * 2 - (256 * 2 / 4)) the window
scale option is still 7:
192.168.1.38.40676 > 78.47.222.210.5001: Flags [S], seq 2577214362, win 5840, options [mss 1460,sackOK,TS val 338417 ecr 0,nop,wscale 0], length 0
78.47.222.210.5001 > 192.168.1.38.40676: Flags [S.], seq 1570631029, ack 2577214363, win 384, options [mss 1452,sackOK,TS val 2435248895 ecr 338417,nop,wscale 7], length 0
192.168.1.38.40676 > 78.47.222.210.5001: Flags [.], ack 1, win 5840, options [nop,nop,TS val 338421 ecr 2435248895], length 0
Within tcp_select_initial_window() the original space argument - a
representation of the rx buffer size - is expanded during
tcp_select_initial_window(). Only sysctl_tcp_rmem[2], sysctl_rmem_max
and window_clamp are considered to calculate the initial window.
This patch adjust the window_clamp argument if the user explicitly
reduce the receive buffer.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/vhost/net.c
net/bridge/br_device.c
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36f
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
It can happen that there are no packets in queue while calling
tcp_xmit_retransmit_queue(). tcp_write_queue_head() then returns
NULL and that gets deref'ed to get sacked into a local var.
There is no work to do if no packets are outstanding so we just
exit early.
This oops was introduced by 08ebd1721a (tcp: remove tp->lost_out
guard to make joining diff nicer).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Tested-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can pass a gfp argument to tso_fragment() and avoid GFP_ATOMIC
allocations sometimes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 33ad798c92 (tcp: options clean up) introduced a problem
if MD5+SACK+timestamps were used in initial SYN message.
Some stacks (old linux for example) try to negotiate MD5+SACK+TSTAMP
sessions, but since 40 bytes of tcp options space are not enough to
store all the bits needed, we chose to disable timestamps in this case.
We send a SYN-ACK _without_ timestamp option, but socket has timestamps
enabled and all further outgoing messages contain a TS block, all with
the initial timestamp of the remote peer.
Fix is to really disable timestamps option for the whole session.
Reported-by: Bijay Singh <Bijay.Singh@guavus.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the
sk->sk_route_caps &= ~NETIF_F_GSO_MASK
that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)
So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.
Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for TSO segments of an skb in TCP_MIB_OUTSEGS counter. Without
doing this, the counter can be off by orders of magnitude from the
actual number of segments sent.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Herbert Xu said: we should be able to simply replace ipfragok
with skb->local_df. commit f88037(sctp: Drop ipfargok in sctp_xmit function)
has droped ipfragok and set local_df value properly.
The patch kills the ipfragok parameter of .queue_xmit().
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
inet: Remove unused send_check length argument
This patch removes the unused length argument from the send_check
function in struct inet_connection_sock_af_ops.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Yinghai <yinghai.lu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Commit 4957faad (TCPCT part 1g: Responder Cookie => Initiator), part
of TCP_COOKIE_TRANSACTION implementation, forgot to correctly size
synack skb in case user data must be included.
Many thanks to Mika Pentillä for spotting this error.
Reported-by: Penttillä Mika <mika.penttila@ixonos.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtnetlink init_rcvwnd to set the TCP initial receive window size
advertised by passive and active TCP connections.
The current Linux TCP implementation limits the advertised TCP initial
receive window to the one prescribed by slow start. For short lived
TCP connections used for transaction type of traffic (i.e. http
requests), bounding the advertised TCP initial receive window results
in increased latency to complete the transaction.
Support for setting initial congestion window is already supported
using rtnetlink init_cwnd, but the feature is useless without the
ability to set a larger TCP initial receive window.
The rtnetlink init_rcvwnd allows increasing the TCP initial receive
window, allowing TCP connection to advertise larger TCP receive window
than the ones bounded by slow start.
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_push checks tcp_send_head and calls __tcp_push_pending_frames,
which again checks tcp_send_head, and this unnecessary check is
done for every other caller of __tcp_push_pending_frames.
Remove tcp_send_head check in __tcp_push_pending_frames and add
the check to tcp_push_pending_frames. Other functions call
__tcp_push_pending_frames only when tcp_send_head would evaluate
to true.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It creates a regression, triggering badness for SYN_RECV
sockets, for example:
[19148.022102] Badness at net/ipv4/inet_connection_sock.c:293
[19148.022570] NIP: c02a0914 LR: c02a0904 CTR: 00000000
[19148.023035] REGS: eeecbd30 TRAP: 0700 Not tainted (2.6.32)
[19148.023496] MSR: 00029032 <EE,ME,CE,IR,DR> CR: 24002442 XER: 00000000
[19148.024012] TASK = eee9a820[1756] 'privoxy' THREAD: eeeca000
This is likely caused by the change in the 'estab' parameter
passed to tcp_parse_options() when invoked by the functions
in net/ipv4/tcp_minisocks.c
But even if that is fixed, the ->conn_request() changes made in
this patch series is fundamentally wrong. They try to use the
listening socket's 'dst' to probe the route settings. The
listening socket doesn't even have a route, and you can't
get the right route (the child request one) until much later
after we setup all of the state, and it must be done by hand.
This stuff really isn't ready, so the best thing to do is a
full revert. This reverts the following commits:
f55017a93f022c3f7d821aba721ebacda42ebd67345cda2fd6dc343475ed05eaade2786a2a2d6bf8
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise:
ERROR: "sysctl_tcp_cookie_size" [net/ipv6/ipv6.ko] undefined!
make[1]: *** [__modpost] Error 1
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/tcp_output.c: In function ‘tcp_make_synack’:
net/ipv4/tcp_output.c:2488: warning: cast from pointer to integer of different size
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse incoming TCP_COOKIE option(s).
Calculate <SYN,ACK> TCP_COOKIE option.
Send optional <SYN,ACK> data.
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
Requires:
TCPCT part 1a: add request_values parameter for sending SYNACK
TCPCT part 1b: generate Responder Cookie secret
TCPCT part 1c: sysctl_tcp_cookie_size, socket option TCP_COOKIE_TRANSACTIONS
TCPCT part 1d: define TCP cookie option, extend existing struct's
TCPCT part 1e: implement socket option TCP_COOKIE_TRANSACTIONS
TCPCT part 1f: Initiator Cookie => Responder
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate and format <SYN> TCP_COOKIE option.
This is a significantly revised implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
Requires:
TCPCT part 1c: sysctl_tcp_cookie_size, socket option TCP_COOKIE_TRANSACTIONS
TCPCT part 1d: define TCP cookie option, extend existing struct's
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Define sysctl (tcp_cookie_size) to turn on and off the cookie option
default globally, instead of a compiled configuration option.
Define per socket option (TCP_COOKIE_TRANSACTIONS) for setting constant
data values, retrieving variable cookie values, and other facilities.
Move inline tcp_clear_options() unchanged from net/tcp.h to linux/tcp.h,
near its corresponding struct tcp_options_received (prior to changes).
This is a straightforward re-implementation of an earlier (year-old)
patch that no longer applies cleanly, with permission of the original
author (Adam Langley):
http://thread.gmane.org/gmane.linux.network/102586
These functions will also be used in subsequent patches that implement
additional features.
Requires:
net: TCP_MSS_DEFAULT, TCP_MSS_DESIRED
Signed-off-by: William.Allen.Simpson@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional function parameters associated with sending SYNACK.
These parameters are not needed after sending SYNACK, and are not
used for retransmission. Avoids extending struct tcp_request_sock,
and avoids allocating kernel memory.
Also affects DCCP as it uses common struct request_sock_ops,
but this parameter is currently reserved for future use.
Signed-off-by: William.Allen.Simpson@gmail.com
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use no window scale bit in the features field.
Note that this is not the same as setting a window scale of 0
as would happen with window limit on route.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement querying and acting upon the no timestamp bit in the feature
field.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement querying and acting upon the no sack bit in the features
field.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acknowledge TCP window scale support by inserting the proper option in SYN/ACK
and SYN headers even if our window scale is zero.
This fixes the following observed behavior:
1. Client sends a SYN with TCP window scaling option and non zero window scale
value to a Linux box.
2. Linux box notes large receive window from client.
3. Linux decides on a zero value of window scale for its part.
4. Due to compare against requested window scale size option, Linux does not to
send windows scale TCP option header on SYN/ACK at all.
With the following result:
Client box thinks TCP window scaling is not supported, since SYN/ACK had no
TCP window scale option, while Linux thinks that TCP window scaling is
supported (and scale might be non zero), since SYN had TCP window scale
option and we have a mismatched idea between the client and server
regarding window sizes.
Probably it also fixes up the following bug (not observed in practice):
1. Linux box opens TCP connection to some server.
2. Linux decides on zero value of window scale.
3. Due to compare against computed window scale size option, Linux does
not to set windows scale TCP option header on SYN.
With the expected result that the server OS does not use window scale option
due to not receiving such an option in the SYN headers, leading to suboptimal
performance.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Signed-off-by: Ori Finkelman <ori@comsleep.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock
mount_root => nfs_root_data => tcp_close => lock sk_lock =>
tcp_send_fin => alloc_skb_fclone => page reclaim
David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.
But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for something else I spent some time adding
one liner comments to the tcp_output.c functions that
didn't have any. That makes the comments more consistent.
I hope I documented everything right.
No code changes.
v2: Incorporated feedback from Ilpo.
v3: Change style of one liner comments, add a few more comments.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket starts out on a non-TSO route, and then switches to
a TSO route, then the tail on the tx queue can morph into a TSO
packet, causing mischief because the rest of the stack does not
expect a partially linear TSO packet.
This patch fixes this by ensuring that skb->ip_summed is set to
CHECKSUM_PARTIAL before declaring a packet as TSO.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be very safe compared with full enabled, so I see
no reason why it shouldn't be done right away. As ECN can only
be negotiated if the SYN sending party is also supporting it,
somebody in the loop probably knows what he/she is doing. If
SYN does not ask for ECN, the server side SYN-ACK is identical
to what it is without ECN. Thus it's quite safe.
The chosen value is safe w.r.t to existing configs which
choose to currently set manually either 0 or 1 but
silently upgrades those who have not explicitly requested
ECN off.
Whether to just enable both sides comes up time to time but
unless that gets done now we can at least make the servers
aware of ECN already. As there are some known problems to occur
if ECN is enabled, it's currently questionable whether there's
any real gain from enabling clients as servers mostly won't
support it anyway (so we'd hit just the negative sides). After
enabling the servers and getting that deployed, the client end
enable really has some potential gain too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just noticed while doing some new work that the recent
mid-wq adjustment logic will misbehave when FACK is not
in use (happens either due sysctl'ed off or auto-detected
reordering) because I forgot the relevant TCPCB tagbit.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that trivial reset of pcount to one was not sufficient
in tcp_retransmit_skb. Multiple counters experience a positive
miscount when skb's pcount gets lowered without the necessary
adjustments (depending on skb's sacked bits which exactly), at
worst a packets_out miscount can crash at RTO if the write queue
is empty!
Triggering this requires mss change, so bidir tcp or mtu probe or
like.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need full-scale adjustment to fix a TCP miscount in the next
patch, so just move it into a helper and call for that from the
other places.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's very little need for most of the callsites to get
tp->xmit_goal_size updated. That will cost us divide as is,
so slice the function in two. Also, the only users of the
tp->xmit_goal_size are directly behind tcp_current_mss(),
so there's no need to store that variable into tcp_sock
at all! The drop of xmit_goal_size currently leaves 16-bit
hole and some reorganization would again be necessary to
change that (but I'm aiming to fill that hole with u16
xmit_goal_size_segs to cache the results of the remaining
divide to get that tso on regression).
Bring xmit_goal_size parts into tcp.c
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pure assignment case, the earlier zeroing is
still in effect.
David S. Miller raised concerns if the ifs are there to avoid
dirtying cachelines. I came to these conclusions:
> We'll be dirty it anyway (now that I check), the first "real" statement
> in tcp_rcv_established is:
>
> tp->rx_opt.saw_tstamp = 0;
>
> ...that'll land on the same dword. :-/
>
> I suppose the blocks are there just because they had more complexity
> inside when they had to calculate the eff_sacks too (maybe it would
> have been better to just remove them in that drop-patch so you would
> have had less head-ache :-)).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The above functions from include/net/tcp.h have been defined with an
argument that they never use. The argument is 'u32 ack' which is never
used inside the function body, and thus it can be removed. The rest of
the patch involves the necessary changes to the function callers of the
above two functions.
Signed-off-by: Hantzis Fotis <xantzis@ceid.upatras.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
I guess these fields were one day 16-bit in the struct but
nowadays they're just using 8 bits anyway.
This is just a precaution, didn't result any change in my
case but who knows what all those varying gcc versions &
options do. I've been told that 16-bit is not so nice with
some cpus.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes insignificant bug that would cause sending of stale
SACK block (would occur in some corner cases).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If cur_mss grew very recently so that the previously G/TSOed skb
now fits well into a single segment it would get send up in
parts unless we calculate # of segments again. This corner-case
could happen eg. after mtu probe completes or less than
previously sack blocks are required for the opposite direction.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) We didn't remove any skbs, so no need to handle stale refs.
2) scoreboard_skb_hint is trivial, no timestamps were changed
so no need to clear that one
3) lost_skb_hint needs tweaking similar to that of
tcp_sacktag_one().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb can be sent right away, we certainly should do that
if it's in the middle of the queue because it won't get
more data into it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backtracking to sacked skbs is a horrible performance killer
since the hint cannot be advanced successfully past them...
...And it's totally unnecessary too.
In theory this is 2.6.27..28 regression but I doubt anybody
can make .28 to have worse performance because of other TCP
improvements.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our TCP stack does not set the urgent flag if the urgent pointer
does not fit in 16 bits, i.e., if it is more than 64K from the
sequence number of a packet.
This behaviour is different from the BSDs, and clearly contradicts
the purpose of urgent mode, which is to send the notification
(though not necessarily the associated data) as soon as possible.
Our current behaviour may in fact delay the urgent notification
indefinitely if the receiver window does not open up.
Simply matching BSD however may break legacy applications which
incorrectly rely on the out-of-band delivery of urgent data, and
conversely the in-band delivery of non-urgent data.
Alexey Kuznetsov suggested a safe solution of following BSD only
if the urgent pointer itself has not yet been transmitted. This
way we guarantee that when the remote end sees the packet with
non-urgent data marked as urgent due to wrap-around we would have
advanced the urgent pointer beyond, either to the actual urgent
data or to an as-yet untransmitted packet.
The only potential downside is that applications on the remote
end may see multiple SIGURG notifications. However, this would
occur anyway with other TCP stacks. More importantly, the outcome
of such a duplicate notification is likely to be harmless since
the signal itself does not carry any information other than the
fact that we're in urgent mode.
Thanks to Ilpo Järvinen for fixing a critical bug in this and
Jeff Chua for reporting that bug.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is obsolete since the passes got combined.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our TCP stack does not set the urgent flag if the urgent pointer
does not fit in 16 bits, i.e., if it is more than 64K from the
sequence number of a packet.
This behaviour is different from the BSDs, and clearly contradicts
the purpose of urgent mode, which is to send the notification
(though not necessarily the associated data) as soon as possible.
Our current behaviour may in fact delay the urgent notification
indefinitely if the receiver window does not open up.
Simply matching BSD however may break legacy applications which
incorrectly rely on the out-of-band delivery of urgent data, and
conversely the in-band delivery of non-urgent data.
Alexey Kuznetsov suggested a safe solution of following BSD only
if the urgent pointer itself has not yet been transmitted. This
way we guarantee that when the remote end sees the packet with
non-urgent data marked as urgent due to wrap-around we would have
advanced the urgent pointer beyond, either to the actual urgent
data or to an as-yet untransmitted packet.
The only potential downside is that applications on the remote
end may see multiple SIGURG notifications. However, this would
occur anyway with other TCP stacks. More importantly, the outcome
of such a duplicate notification is likely to be harmless since
the signal itself does not carry any information other than the
fact that we're in urgent mode.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since jiffies is unsigned long, the types get expanded into
that and after long enough time the difference will therefore
always be > 1 (and that probably happens near boot as well as
iirc the first jiffies wrap is scheduler close after boot to
find out problems related to that early).
This was originally noted by Bill Fink in Dec'07 but nobody
never ended fixing it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_minshall_update is not significant difference since it only
checks for not full-sized skb which is BUG'ed on the push_one
path anyway.
tcp_snd_test is tcp_nagle_test+tcp_cwnd_test+tcp_snd_wnd_test,
just the order changed slightly.
net/ipv4/tcp_output.c:
tcp_snd_test | -89
tcp_mss_split_point | -91
tcp_may_send_now | +53
tcp_cwnd_validate | -98
tso_fragment | -239
__tcp_push_pending_frames | -1340
tcp_push_one | -146
7 functions changed, 53 bytes added, 2003 bytes removed, diff: -1950
net/ipv4/tcp_output.c:
tcp_write_xmit | +1772
1 function changed, 1772 bytes added, diff: +1772
tcp_output.o.new:
8 functions changed, 1825 bytes added, 2003 bytes removed, diff: -178
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I should have noticed this earlier... :-) The previous solution
to URG+GSO/TSO will cause SACK block tcp_fragment to do zig-zig
patterns, or even worse, a steep downward slope into packet
counting because each skb pcount would be truncated to pcount
of 2 and then the following fragments of the later portion would
restore the window again.
Basically this reverts "tcp: Do not use TSO/GSO when there is
urgent data" (33cf71cee1). It also removes some unnecessary code
from tcp_current_mss that didn't work as intented either (could
be that something was changed down the road, or it might have
been broken since the dawn of time) because it only works once
urg is already written while this bug shows up starting from
~64k before the urg point.
The retransmissions already are split to mss sized chunks, so
only new data sending paths need splitting in case they have
a segment otherwise suitable for gso/tso. The actually check
can be improved to be more narrow but since this is late -rc
already, I'll postpone thinking the more fine-grained things.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I always had thought that collapsing up to two at a time was
intentional decision to avoid excessive processing if 1 byte
sized skbs are to be combined for a full mtu, and consecutive
retransmissions would make the size of the retransmittee
double each round anyway, but some recent discussion made me
to understand that was not the case. Thus make collapse work
more and wait less.
It would be possible to take advantage of the shifting
machinery (added in the later patch) in the case of paged
data but that can be implemented on top of this change.
tcp_skb_is_last check is now provided by the loop.
I tested a bit (ss-after-idle-off, fill 4096x4096B xfer,
10s sleep + 4096 x 1byte writes while dropping them for
some a while with netem):
. 16774097:16775545(1448) ack 1 win 46
. 16775545:16776993(1448) ack 1 win 46
. ack 16759617 win 2399
P 16776993:16777217(224) ack 1 win 46
. ack 16762513 win 2399
. ack 16765409 win 2399
. ack 16768305 win 2399
. ack 16771201 win 2399
. ack 16774097 win 2399
. ack 16776993 win 2399
. ack 16777217 win 2399
P 16777217:16777257(40) ack 1 win 46
. ack 16777257 win 2399
P 16777257:16778705(1448) ack 1 win 46
P 16778705:16780153(1448) ack 1 win 46
FP 16780153:16781313(1160) ack 1 win 46
. ack 16778705 win 2399
. ack 16780153 win 2399
F 1:1(0) ack 16781314 win 2399
While without drop-all period I get this:
. 16773585:16775033(1448) ack 1 win 46
. ack 16764897 win 9367
. ack 16767793 win 9367
. ack 16770689 win 9367
. ack 16773585 win 9367
. 16775033:16776481(1448) ack 1 win 46
P 16776481:16777217(736) ack 1 win 46
. ack 16776481 win 9367
. ack 16777217 win 9367
P 16777217:16777218(1) ack 1 win 46
P 16777218:16777219(1) ack 1 win 46
P 16777219:16777220(1) ack 1 win 46
...
P 16777247:16777248(1) ack 1 win 46
. ack 16777218 win 9367
. ack 16777219 win 9367
...
. ack 16777233 win 9367
. ack 16777248 win 9367
P 16777248:16778696(1448) ack 1 win 46
P 16778696:16780144(1448) ack 1 win 46
FP 16780144:16781313(1169) ack 1 win 46
. ack 16780144 win 9367
F 1:1(0) ack 16781314 win 9367
The window seems to be 30-40 segments, which were successfully
combined into: P 16777217:16777257(40) ack 1 win 46
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=12014
Since most (if not all) implementations of TSO and even the in-kernel
software GSO do not update the urgent pointer when splitting a large
segment, it is necessary to turn off TSO/GSO for all outgoing traffic
with the URG pointer set.
Looking at tcp_current_mss (and the preceding comment) I even think
this was the original intention. However, this approach is insufficient,
because TSO/GSO is turned off only for newly created frames, not for
frames which were already pending at the arrival of a message with
MSG_OOB set. These frames were created when TSO/GSO was enabled,
so they may be large, and they will have the urgent pointer set
in tcp_transmit_skb().
With this patch, such large packets will be fragmented again before
going to the transmit routine.
As a side note, at least the following NICs are known to screw up
the urgent pointer in the TCP header when doing TSO:
Intel 82566MM (PCI ID 8086:1049)
Intel 82566DC (PCI ID 8086:104b)
Intel 82541GI (PCI ID 8086:1076)
Broadcom NetXtreme II BCM5708 (PCI ID 14e4:164c)
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Miller noticed that commit
33ad798c92 '(tcp: options clean up')
did not move the req->cookie_ts check.
This essentially disabled commit 4dfc281702
'[Syncookies]: Add support for TCP options via timestamps.'.
This restores the original logic.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not our bug! Sadly some devices cannot cope with the change
of TCP option ordering which was a result of the recent rewrite of
the option code (not that there was some particular reason steming
from the rewrite for the reordering) though any ordering of TCP
options is perfectly legal. Thus we restore the original ordering
to allow interoperability with/through such broken devices and add
some warning about this trap. Since the reordering just happened
without any particular reason, this change shouldn't cost us
anything.
There are already couple of known failure reports (within close
proximity of the last release), so the problem might be more
wide-spread than a single device. And other reports which may
be due to the same problem though the symptoms were less obvious.
Analysis of one of the case revealed (with very high probability)
that sack capability cannot be negotiated as the first option
(SYN never got a response).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Aldo Maggi <sentiniate@tiscali.it>
Tested-by: Aldo Maggi <sentiniate@tiscali.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for the recent "sack issue" I also read all eff_sacks
usage that was played around by some relevant commit. I found
out that there's another thing that is asking for a fix (unrelated
to the "sack issue" though).
This feature has probably very little significance in practice.
Opposite direction timeout with bidirectional tcp comes to me as
the most likely scenario though there might be other cases as
well related to non-data segments we send (e.g., response to the
opposite direction segment). Also some ACK losses or option space
wasted for other purposes is necessary to prevent the earlier
SACK feedback getting to the sender.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It all started from me noticing that this urgent check in
tcp_clean_rtx_queue is unnecessarily inside the loop. Then
I took a longer look to it and found out that the users of
urg_mode can trivially do without, well almost, there was
one gotcha.
Bonus: those funny people who use urg with >= 2^31 write_seq -
snd_una could now rejoice too (that's the only purpose for the
between being there, otherwise a simple compare would have done
the thing). Not that I assume that the rest of the tcp code
happily lives with such mind-boggling numbers :-). Alas, it
turned out to be impossible to set wmem to such numbers anyway,
yes I really tried a big sendfile after setting some wmem but
nothing happened :-). ...Tcp_wmem is int and so is sk_sndbuf...
So I hacked a bit variable to long and found out that it seems
to work... :-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current TCP code relies on the local port of the listening socket
being the same as the destination address of the incoming
connection. Port redirection used by many transparent proxying
techniques obviously breaks this, so we have to store the original
destination port address.
This patch extends struct inet_request_sock and stores the incoming
destination port value there. It also modifies the handshake code to
use that value as the source port when sending reply packets.
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm trying to use the TCP_MAXSEG option to setsockopt() to set the MSS
for both sides of a bidirectional connection.
man tcp says: "If this option is set before connection establishment, it
also changes the MSS value announced to the other end in the initial
packet."
However, the kernel only uses the MTU/route cache to set the advertised
MSS. That means if I set the MSS to, say, 500 before calling connect(),
I will send at most 500-byte packets, but I will still receive 1500-byte
packets in reply.
This is a bug, either in the kernel or the documentation.
This patch (applies to latest net-2.6) reduces the advertised value to
that requested by the user as long as setsockopt() is called before
connect() or accept(). This seems like the behavior that one would
expect as well as that which is documented.
I've tried to make sure that things that depend on the advertised MSS
are set correctly.
Signed-off-by: Tom Quetchenbach <virtualphtn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If lost skb is sacked, we might have nothing to retransmit
as high as the retransmit_high is pointing to, so place
it lower to avoid unnecessary walking.
This is mainly for the case where high L'ed skbs gets sacked.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most importantly avoid doing it with cumulative ACK. Not clearing
means that we no longer need n^2 processing in resolution of each
fast recovery.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't much sense here afaict, probably never has. Since
fragmenting and collapsing deal the hints by themselves, there
should be very little reason for the rexmit loop to do that.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both loops are quite similar, so they can be combined
with little effort. As a result, forward_skb_hint becomes
obsolete as well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The validity of the retransmit_high must then be ensured
if no L'ed skb exits!
This makes a minor change to behavior, we now have to
iterate the head to find out that the loop terminates.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main benefit in this is that we can then freely point
the retransmit_skb_hint to anywhere we want to because
there's no longer need to know what would be the count
changes involve, and since this is really used only as a
terminator, unnecessary work is one time walk at most,
and if some retransmissions are necessary after that
point later on, the walk is not full waste of time
anyway.
Since retransmit_high must be kept valid, all lost
markers must ensure that.
Now I also have learned how those "holes" in the
rexmittable skbs can appear, mtu probe does them. So
I removed the misleading comment as well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ie., the difference between partial and all clearing doesn't
exists anymore since the SACK optimizations got dropped by
an sacktag rewrite.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the TCP header is miscalculated when the window scale ends
up being 0. Additionally, this can be induced by sending a SYN to a
passive open port with a window scale option with value 0.
Signed-off-by: Philip Love <love_phil@emc.com>
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Alexey Dobriyan:
CHECK net/ipv4/tcp_output.c
net/ipv4/tcp_output.c:475:7: warning: dubious: !x & y
And sparse is damn right!
if (unlikely(!OPTION_TS & opts->options))
^^^
size += TCPOLEN_SACKPERM_ALIGNED;
OPTION_TS is (1 << 1), so condition will never trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
This should fix the following bugs:
* Connections with MD5 signatures produce invalid packets whenever SACK
options are included
* MD5 signatures are counted twice in the MSS calculations
Behaviour changes:
* A SYN with MD5 + SACK + TS elicits a SYNACK with MD5 + SACK
This is because we can't fit any SACK blocks in a packet with MD5 + TS
options. There was discussion about disabling SACK rather than TS in
order to fit in better with old, buggy kernels, but that was deemed to
be unnecessary.
* SYNs with MD5 don't include a TS option
See above.
Additionally, it removes a bunch of duplicated logic for calculating options,
which should help avoid these sort of issues in the future.
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the MD5 code assumes that the SKBs are linear and, in the case
that they aren't, happily goes off and hashes off the end of the SKB and
into random memory.
Reported by Stephen Hemminger in [1]. Advice thanks to Stephen and Evgeniy
Polyakov. Also includes a couple of missed route_caps from Stephen's patch
in [2].
[1] http://marc.info/?l=linux-netdev&m=121445989106145&w=2
[2] http://marc.info/?l=linux-netdev&m=121459157816964&w=2
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fortunately (almost) all the TCP code has a sock to get the net from :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some places in TCP that select one MIB index to
bump snmp statistics like this:
if (<something>)
NET_INC_STATS_BH(<some_id>);
else if (<something_else>)
NET_INC_STATS_BH(<some_other_id>);
...
else
NET_INC_STATS_BH(<default_id>);
or in a more tricky but still similar way.
On the other hand, this NET_INC_STATS_BH is a camouflaged
increment of percpu variable, which is not that small.
Factoring those cases out de-bloats 235 bytes on non-preemptible
i386 config and drives parts of the code into 80 columns.
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-235 (-235)
function old new delta
tcp_fastretrans_alert 1437 1424 -13
tcp_dsack_set 137 124 -13
tcp_xmit_retransmit_queue 690 676 -14
tcp_try_undo_recovery 283 265 -18
tcp_sacktag_write_queue 1550 1515 -35
tcp_update_reordering 162 106 -56
tcp_retransmit_timer 990 904 -86
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP "resets sent" counter is not incremented when a TCP Reset is
sent via tcp_send_active_reset().
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are seeing an issue with TCP in handling an ICMP frag needed
message that is received after net.ipv4.tcp_retries1 retransmits.
The default value of retries1 is 3. So if the path mtu changes
and ICMP frag needed is lost for the first 3 retransmits or if
it gets delayed until 3 retransmits are done, TCP doesn't update
MSS correctly and continues to retransmit the orginal message
until it timesout after tcp_retries2 retransmits.
I am seeing this issue even with the latest 2.6.25.4 kernel.
In tcp_retransmit_timer(), when retransmits counter exceeds
tcp_retries1 value, the dst cache entry of the socket is reset.
At this time, if we receive an ICMP frag needed message, the
dst entry gets updated with the new MTU, but the TCP sockets
dst_cache entry remains NULL.
So the next time when we try to retransmit after the ICMP frag
needed is received, tcp_retransmit_skb() gets called. Here the
cur_mss value is calculated at the start of the routine with
a NULL sk_dst_cache. Instead we should call tcp_current_mss after
the rebuild_header that caches the dst entry with the updated mtu.
Also the rebuild_header should be called before tcp_fragment
so that skb is fragmented if the mss goes down.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed can only be more strict than what was checked by the
earlier common case check for non-tail skbs, thus
cwnd_len <= needed will never match in that case anyway.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the use of SACK and window scaling when syncookies are used
and the client supports tcp timestamps. Options are encoded into
the timestamp sent in the syn-ack and restored from the timestamp
echo when the ack is received.
Based on earlier work by Glenn Griffin.
This patch avoids increasing the size of structs by encoding TCP
options into the least significant bits of the timestamp and
by not using any 'timestamp offset'.
The downside is that the timestamp sent in the packet after the synack
will increase by several seconds.
changes since v1:
don't duplicate timestamp echo decoding function, put it into ipv4/syncookie.c
and have ipv6/syncookies.c use it.
Feedback from Glenn Griffin: fix line indented with spaces, kill redundant if ()
Reviewed-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes Bugzilla #10384
tcp_simple_retransmit does L increment without any checking
whatsoever for overflowing S+L when Reno is in use.
The simplest scenario I can currently think of is rather
complex in practice (there might be some more straightforward
cases though). Ie., if mss is reduced during mtu probing, it
may end up marking everything lost and if some duplicate ACKs
arrived prior to that sacked_out will be non-zero as well,
leading to S+L > packets_out, tcp_clean_rtx_queue on the next
cumulative ACK or tcp_fastretrans_alert on the next duplicate
ACK will fix the S counter.
More straightforward (but questionable) solution would be to
just call tcp_reset_reno_sack() in tcp_simple_retransmit but
it would negatively impact the probe's retransmission, ie.,
the retransmissions would not occur if some duplicate ACKs
had arrived.
So I had to add reno sacked_out reseting to CA_Loss state
when the first cumulative ACK arrives (this stale sacked_out
might actually be the explanation for the reports of left_out
overflows in kernel prior to 2.6.23 and S+L overflow reports
of 2.6.24). However, this alone won't be enough to fix kernel
before 2.6.24 because it is building on top of the commit
1b6d427bb7 ([TCP]: Reduce sacked_out with reno when purging
write_queue) to keep the sacked_out from overflowing.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update: My mailer ate one of Jarek's feedback mails... Fixed the
parameter in netif_set_gso_max_size() to be u32, not u16. Fixed the
whitespace issue due to a patch import botch. Changed the types from
u32 to unsigned int to be more consistent with other variables in the
area. Also brought the patch up to the latest net-2.6.26 tree.
Update: Made gso_max_size container 32 bits, not 16. Moved the
location of gso_max_size within netdev to be less hotpath. Made more
consistent names between the sock and netdev layers, and added a
define for the max GSO size.
Update: Respun for net-2.6.26 tree.
Update: changed max_gso_frame_size and sk_gso_max_size from signed to
unsigned - thanks Stephen!
This patch adds the ability for device drivers to control the size of
the TSO frames being sent to them, per TCP connection. By setting the
netdevice's gso_max_size value, the socket layer will set the GSO
frame size based on that value. This will propogate into the TCP
layer, and send TSO's of that size to the hardware.
This can be desirable to help tune the bursty nature of TSO on a
per-adapter basis, where one may have 1 GbE and 10 GbE devices
coexisting in a system, one running multiqueue and the other not, etc.
This can also be desirable for devices that cannot support full 64 KB
TSO's, but still want to benefit from some level of segmentation
offloading.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When selecting a new window, tcp_select_window() tries not to shrink
the offered window by using the maximum of the remaining offered window
size and the newly calculated window size. The newly calculated window
size is always a multiple of the window scaling factor, the remaining
window size however might not be since it depends on rcv_wup/rcv_nxt.
This means we're effectively shrinking the window when scaling it down.
The dump below shows the problem (scaling factor 2^7):
- Window size of 557 (71296) is advertised, up to 3111907257:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . ack 3111835961 win 557 <...>
- New window size of 514 (65792) is advertised, up to 3111907217, 40 bytes
below the last end:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . 3113575668:3113577116(1448) ack 3111841425 win 514 <...>
The number 40 results from downscaling the remaining window:
3111907257 - 3111841425 = 65832
65832 / 2^7 = 514
65832 % 2^7 = 40
If the sender uses up the entire window before it is shrunk, this can have
chaotic effects on the connection. When sending ACKs, tcp_acceptable_seq()
will notice that the window has been shrunk since tcp_wnd_end() is before
tp->snd_nxt, which makes it choose tcp_wnd_end() as sequence number.
This will fail the receivers checks in tcp_sequence() however since it
is before it's tp->rcv_wup, making it respond with a dupack.
If both sides are in this condition, this leads to a constant flood of
ACKs until the connection times out.
Make sure the window is never shrunk by aligning the remaining window to
the window scaling factor.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TSO it was possible to send past the receiver window when the skb
to be sent was the last in the write queue while the receiver window
is the limiting factor. One can notice that there's a loophole in the
tcp_mss_split_point that lacked a receiver window check for the
tcp_write_queue_tail() if also cwnd was smaller than the full skb.
Noticed by Thomas Gleixner <tglx@linutronix.de> in form of "Treason
uncloaked! Peer ... shrinks window .... Repaired." messages (the peer
didn't actually shrink its window as the message suggests, we had just
sent something past it without a permission to do so).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated to incorporate Eric's suggestion of using a per cpu buffer
rather than allocating on the stack. Just a two line change, but will
resend in it's entirety.
Signed-off-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This patch removes the no longer used
EXPORT_SYMBOL(sysctl_tcp_tso_win_divisor).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of segments which are purely for control without any
data (SYN/ACK/FIN/RST), many fields are set to common values
in multiple places.
i386 results:
$ gcc --version
gcc (GCC) 4.1.2 20070626 (Red Hat 4.1.2-13)
$ codiff tcp_output.o.old tcp_output.o.new
net/ipv4/tcp_output.c:
tcp_xmit_probe_skb | -48
tcp_send_ack | -56
tcp_retransmit_skb | -79
tcp_connect | -43
tcp_send_active_reset | -35
tcp_make_synack | -42
tcp_send_fin | -48
7 functions changed, 351 bytes removed
net/ipv4/tcp_output.c:
tcp_init_nondata_skb | +90
1 function changed, 90 bytes added
tcp_output.o.mid:
8 functions changed, 90 bytes added, 351 bytes removed, diff: -261
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were manually selected from indent's results which as is
are too noisy to be of any use without human reason. In addition,
some extra newlines between function and its comment were removed
too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snd_up check should be enough. I suspect this has been
there to provide a minor optimization in clean_rtx_queue which
used to have a small if (!->sacked) block which could skip
snd_up check among the other work.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's very little need to have the packets_out incrementing in
a separate function. Also name the combined function
appropriately.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces new memory accounting functions for each network
protocol. Most of them are renamed from memory accounting functions
for stream protocols. At the same time, some stream memory accounting
functions are removed since other functions do same thing.
Renaming:
sk_stream_free_skb() -> sk_wmem_free_skb()
__sk_stream_mem_reclaim() -> __sk_mem_reclaim()
sk_stream_mem_reclaim() -> sk_mem_reclaim()
sk_stream_mem_schedule -> __sk_mem_schedule()
sk_stream_pages() -> sk_mem_pages()
sk_stream_rmem_schedule() -> sk_rmem_schedule()
sk_stream_wmem_schedule() -> sk_wmem_schedule()
sk_charge_skb() -> sk_mem_charge()
Removeing
sk_stream_rfree(): consolidates into sock_rfree()
sk_stream_set_owner_r(): consolidates into skb_set_owner_r()
sk_stream_mem_schedule()
The following functions are added.
sk_has_account(): check if the protocol supports accounting
sk_mem_uncharge(): do the opposite of sk_mem_charge()
In addition, to achieve consolidation, updating sk_wmem_queued is
removed from sk_mem_charge().
Next, to consolidate memory accounting functions, this patch adds
memory accounting calls to network core functions. Moreover, present
memory accounting call is renamed to new accounting call.
Finally we replace present memory accounting calls with new interface
in TCP and SCTP.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Hideo Aoki <haoki@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If snd_wnd - snd_nxt wasn't multiple of MSS, skb was split on
odd boundary by the callers of tcp_window_allows.
We try really hard to avoid unnecessary modulos. Therefore the
old caller side check "if (skb->len < limit)" was too wide as
well because limit is not bound in any way to skb->len and can
cause spurious testing for trimming in the middle of the queue
while we only wanted that to happen at the tail of the queue.
A simple additional caller side check for tcp_write_queue_tail
would likely have resulted 2 x modulos because the limit would
have to be first calculated from window, however, doing that
unnecessary modulo is not mandatory. After a minor change to
the algorithm, simply determine first if the modulo is needed
at all and at that point immediately decide also from which
value it should be calculated from.
This approach also kills some duplicated code.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 'free_space' variable in __tcp_select_window() is signed,
expression (free_space / 2) forces compiler to emit an integer divide.
This can be changed to a plain right shift, less expensive.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'd say that most of what tcp_tso_should_defer had in between
there was dead code because of this.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointing to the next skb is necessary to avoid referencing
already SACKed skbs which will soon be on a separate list.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lines won't be that long and it's compiler's job to optimize
them.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
They better be valid when call to write_queue functions is made
once things that follow are going in.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd argument is always zero (according to grep :) Eliminate
it and merge the function with sk_stream_alloc_skb.
This saves 44 more bytes, and together with the previous patch
we have:
add/remove: 1/0 grow/shrink: 0/8 up/down: 183/-751 (-568)
function old new delta
sk_stream_alloc_skb - 183 +183
ip_rt_init 529 525 -4
arp_ignore 112 107 -5
__inet_lookup_listener 284 274 -10
tcp_sendmsg 2583 2481 -102
tcp_sendpage 1449 1300 -149
tso_fragment 417 258 -159
tcp_fragment 1149 988 -161
__tcp_push_pending_frames 1998 1837 -161
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better place exists in update_send_head (other non-queue related
adjustments are done there as well) which is the only caller of
tcp_advance_send_head (now that the bogus call from mtu_probe is
gone).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key points of this patch are:
- In case new SACK information is advance only type, no skb
processing below previously discovered highest point is done
- Optimize cases below highest point too since there's no need
to always go up to highest point (which is very likely still
present in that SACK), this is not entirely true though
because I'm dropping the fastpath_skb_hint which could
previously optimize those cases even better. Whether that's
significant, I'm not too sure.
Currently it will provide skipping by walking. Combined with
RB-tree, all skipping would become fast too regardless of window
size (can be done incrementally later).
Previously a number of cases in TCP SACK processing fails to
take advantage of costly stored information in sack_recv_cache,
most importantly, expected events such as cumulative ACK and new
hole ACKs. Processing on such ACKs result in rather long walks
building up latencies (which easily gets nasty when window is
huge). Those latencies are often completely unnecessary
compared with the amount of _new_ information received, usually
for cumulative ACK there's no new information at all, yet TCP
walks whole queue unnecessary potentially taking a number of
costly cache misses on the way, etc.!
Since the inclusion of highest_sack, there's a lot information
that is very likely redundant (SACK fastpath hint stuff,
fackets_out, highest_sack), though there's no ultimate guarantee
that they'll remain the same whole the time (in all unearthly
scenarios). Take advantage of this knowledge here and drop
fastpath hint and use direct access to highest SACKed skb as
a replacement.
Effectively "special cased" fastpath is dropped. This change
adds some complexity to introduce better coveraged "fastpath",
though the added complexity should make TCP behave more cache
friendly.
The current ACK's SACK blocks are compared against each cached
block individially and only ranges that are new are then scanned
by the high constant walk. For other parts of write queue, even
when in previously known part of the SACK blocks, a faster skip
function is used (if necessary at all). In addition, whenever
possible, TCP fast-forwards to highest_sack skb that was made
available by an earlier patch. In typical case, no other things
but this fast-forward and mandatory markings after that occur
making the access pattern quite similar to the former fastpath
"special case".
DSACKs are special case that must always be walked.
The local to recv_sack_cache copying could be more intelligent
w.r.t DSACKs which are likely to be there only once but that
is left to a separate patch.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is going to replace the sack fastpath hint quite soon... :-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment in tcp_nagle_test suggests that. This bug is very
very old, even 2.4.0 seems to have it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code has striking complexity to perform a query
which can be reduced to a very simple compare.
FIN seqno may be included to write_seq but it should not make
any significant difference here compared to skb->len which was
used previously. One won't end up there with SYN still queued.
Use of write_seq check guarantees that there's a valid skb in
send_head so I removed the extra check.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: John Heffner <jheffner@psc.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It seems that the checked range for receiver window check should
begin from the first rather than from the last skb that is going
to be included to the probe. And that can be achieved without
reference to skbs at all, snd_nxt and write_seq provides the
correct seqno already. Plus, it SHOULD account packets that are
necessary to trigger fast retransmit [RFC4821].
Location of snd_wnd < probe_size/size_needed check is bogus
because it will cause the other if() match as well (due to
snd_nxt >= snd_una invariant).
Removed dead obvious comment.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addition of lost_retrans_low to tcp_sock might be
unnecessary, it's not clear how often lost_retrans worker is
executed when there wasn't work to do.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Passing wrong skb to tcp_adjust_fackets_out could corrupt
fastpath_cnt_hint as tcp_skb_pcount(next_skb) is not included
to it if hint points exactly to the next_skb (it's lagging
behind, see sacktag).
2) When fastpath_skb_hint is put backwards to avoid dangling
skb reference, the skb's pcount must also be removed from count
(not included like above).
Reported by Cedric Le Goater <legoater@free.fr>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was found due to bug report from Cedric Le Goater though
it turned this turned out to be unrelated bug.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I previously added checking to position that is rather poor as
state has already been adjusted quite a bit. Re-placing it above
all state changes should be more robust though the return should
never ever get executed regardless of its place :-).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason to clear the sacktag skb hint when small part
of the rexmit queue changes. Account changes (if any) instead when
fragmenting/collapsing. RTO/FRTO do not touch SACKED_ACKED bits so
no need to discard SACK tag hint at all.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Substraction for fackets_out is unconditional when snd_una
advances, thus there's no need to do it inside the loop. Just
make sure correct bounds are honored.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
