Use CLAIM protocol to make sure the device is available for use.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a replicator port is enabled, we block the traffic
on the other port and route all traffic to the new enabled
port. If there are two active trace sessions each targeting
the two different paths from the replicator, the second session
will disable the first session and route all the data to the
second path.
ETR
/
e.g, replicator
\
ETB
If CPU0 is operated in sysfs mode to ETR and CPU1 is operated
in perf mode to ETB, depending on the order in which the
replicator is enabled one device is blocked.
Ideally we need trace-id for the session to make the
right choice. That implies we need a trace-id allocation
logic for the coresight subsystem and use that to route
the traffic. The short term solution is to only manage
the "target port" and leave the other port untouched.
That leaves both the paths unaffected, except that some
unwanted traffic may be pushed to the paths (if the Trace-IDs
are not far enough), which is still fine and can be filtered
out while processing rather than silently blocking the data.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert component enable/disable messages from dev_info to dev_dbg.
When used with perf, the components in the paths are enabled/disabled
during each schedule of the run, which can flood the dmesg with these
messages. Moreover, they are only useful for debug purposes. So,
convert such messages to dev_dbg() which can be turned on as
needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose