On the Arm Juno platform, the HDLCD pixel clock is constrained to 250KHz
resolution in order to avoid the tiny System Control Processor spending
aeons trying to calculate exact PLL coefficients. This means that modes
like my oddball 1600x1200 with 130.89MHz clock get rejected since the
rate cannot be matched exactly. In practice, though, this mode works
quite happily with the clock at 131MHz, so let's relax the check to
allow a little bit of slop.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Rather than allowing any old mode through, then subsequently refusing
unmatchable clock rates in atomic_check when it's too late to back out
and pick a different mode, let's do that validation up-front where it
will cause unsupported modes to be correctly pruned in the first place.
This also eliminates an issue whereby a perceived clock rate of 0 would
cause atomic disable to fail and prevent the module from being unloaded.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
This patch trying to fix monitor freeze issue caused by drm error
'flip_done timed out' on LS1028A platform. this set try is make a loop
around the second setting CVAL and try like 5 times before giveing up.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fixing the DMA mapping sg segment warning, which shows "DMA-API: mapping
sg segment longer than device claims to support [len=921600] [max=65536]".
Fixed by setting the max segment size at Komeda driver.
This patch depends on:
- https://patchwork.freedesktop.org/series/54448/
- https://patchwork.freedesktop.org/series/54449/
- https://patchwork.freedesktop.org/series/54450/
- https://patchwork.freedesktop.org/series/58976/
Changes since v1:
- Adds member description
- Adds patch denpendency in the comment
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Reviewed-by: Ayan Kumar Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the case of a normal sync update, the preparation of framebuffers (be
it calling drm_atomic_helper_prepare_planes() or doing setups with
drm_framebuffer_get()) are performed in the new_state and the respective
cleanups are performed in the old_state.
In the case of async updates, the preparation is also done in the
new_state but the cleanups are done in the new_state (because updates
are performed in place, i.e. in the current state).
The current code blocks async udpates when the fb is changed, turning
async updates into sync updates, slowing down cursor updates and
introducing regressions in igt tests with errors of type:
"CRITICAL: completed 97 cursor updated in a period of 30 flips, we
expect to complete approximately 15360 updates, with the threshold set
at 7680"
Fb changes in async updates were prevented to avoid the following scenario:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, cleanup fb1
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb2
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2 (wrong)
Where we have a single call to prepare fb2 but double cleanup call to fb2.
To solve the above problems, instead of blocking async fb changes, we
place the old framebuffer in the new_state object, so when the code
performs cleanups in the new_state it will cleanup the old_fb and we
will have the following scenario instead:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, no cleanup
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb1
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2
Where calls to prepare/cleanup are balanced.
Cc: <stable@vger.kernel.org> # v4.14+
Fixes: 25dc194b34 ("drm: Block fb changes for async plane updates")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-6-helen.koike@collabora.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.19+
Fixes: 539c320bfa ("drm/vc4: update cursors asynchronously through atomic")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-5-helen.koike@collabora.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Cc: <stable@vger.kernel.org> # v4.14+
Fixes: 224a4c9709 ("drm/msm: update cursors asynchronously through atomic")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-4-helen.koike@collabora.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 674e78acae ("drm/amd/display: Add fast path for cursor plane updates")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-3-helen.koike@collabora.com
In the case of async update, modifications are done in place, i.e. in the
current plane state, so the new_state is prepared and the new_state is
cleaned up (instead of the old_state, unlike what happens in a
normal sync update).
To cleanup the old_fb properly, it needs to be placed in the new_state
in the end of async_update, so cleanup call will unreference the old_fb
correctly.
Also, the previous code had a:
plane_state = plane->funcs->atomic_duplicate_state(plane);
...
swap(plane_state, plane->state);
if (plane->state->fb && plane->state->fb != new_state->fb) {
...
}
Which was wrong, as the fb were just assigned to be equal, so this if
statement nevers evaluates to true.
Another details is that the function drm_crtc_vblank_get() can only be
called when vop->is_enabled is true, otherwise it has no effect and
trows a WARN_ON().
Calling drm_atomic_set_fb_for_plane() (which get a referent of the new
fb and pus the old fb) is not required, as it is taken care by
drm_mode_cursor_universal() when calling
drm_atomic_helper_update_plane().
Fixes: 15609559a8 ("drm/rockchip: update cursors asynchronously through atomic.")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-2-helen.koike@collabora.com
mtk_dsi_stop() should be called after mtk_drm_crtc_atomic_disable(), which
needs ovl irq for drm_crtc_wait_one_vblank(), since after mtk_dsi_stop() is
called, ovl irq will be disabled. If drm_crtc_wait_one_vblank() is called
after last irq, it will timeout with this message: "vblank wait timed out
on crtc 0". This happens sometimes when turning off the screen.
In drm_atomic_helper.c#disable_outputs(),
the calling sequence when turning off the screen is:
1. mtk_dsi_encoder_disable()
--> mtk_output_dsi_disable()
--> mtk_dsi_stop(); /* sometimes make vblank timeout in
atomic_disable */
--> mtk_dsi_poweroff();
2. mtk_drm_crtc_atomic_disable()
--> drm_crtc_wait_one_vblank();
...
--> mtk_dsi_ddp_stop()
--> mtk_dsi_poweroff();
mtk_dsi_poweroff() has reference count design, change to make
mtk_dsi_stop() called in mtk_dsi_poweroff() when refcount is 0.
Fixes: 0707632b5b ("drm/mediatek: update DSI sub driver flow for sending commands to panel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
num_pipes is used for mutex created in mtk_drm_crtc_create(). If we
don't clear num_pipes count, when rebinding driver, the count will
be accumulated. From mtk_disp_mutex_get(), there can only be at most
10 mutex id. Clear this number so it starts from 0 in every rebind.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
shutdown all CRTC when unbinding drm driver.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Unbinding components (i.e. mtk_dsi and mtk_disp_ovl/rdma/color) will
trigger master(mtk_drm)'s .unbind(), and currently mtk_drm's unbind
won't actually unbind components. During the next bind,
mtk_drm_kms_init() is called, and the components are added back.
.unbind() should call mtk_drm_kms_deinit() to unbind components.
And since component_master_del() in .remove() will trigger .unbind(),
which will also unregister device, it's fine to remove original functions
called here.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
detatch panel in mtk_dsi_destroy_conn_enc(), since .bind will try to
attach it again.
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Save RING_HEAD into vgpu reg when vgpu switched out and report
it's value back to guest.
v6: addressed comment for ring head wrap count support. (Zhenyu)
v5: ring head wrap count support.
v4: updated HEAD/TAIL with guest value, not host value. (Yan Zhao)
v3: save RING HEAD/TAIL vgpu reg in save_ring_hw_state. (Zhenyu Wang)
v2: save RING_TAIL as well during vgpu mmio switch to meet ring_is_idle
condition. (Fred Gao)
v1: based on input from Weinan. (Weinan Li)
[zhenyuw: Include this fix for possible future guest kernel that
would utilize RING_HEAD for hangcheck.]
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Instead of updating by MMIO write, all of the wa regs are initialized by
wa_ctx. From host side, it should make this behavior as expected, add
'F_CMD_ACCESS' flag to these regs and allow access by commands.
[ 123.557608] gvt: vgpu 2: srm access to non-render register (b11c)
[ 123.563728] gvt: vgpu 2: MI_STORE_REGISTER_MEM handler error
[ 123.569409] gvt: vgpu 2: cmd parser error
[ 123.573424] 0x0
[ 123.573425] 0x24
[ 123.578686] gvt: vgpu 2: scan workload error
[ 123.582958] GVT Internal error for the guest
[ 123.587317] Now vgpu 2 will enter failsafe mode.
[ 123.591938] gvt: vgpu 2: failed to submit desc 0
[ 123.596557] gvt: vgpu 2: fail submit workload on ring 0
[ 123.601786] gvt: vgpu 2: fail to emulate MMIO write 00002230 len 4
Acked-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
-----BEGIN PGP SIGNATURE-----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=pg9D
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-05-31' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too crazy, pretty quiet, maybe too quiet.
amdgpu:
- a fixed version of the raven firmware fix we previously reverted
- stolen memory fix
imx:
- regression fix
qxl:
- remove a bad warning
etnaviv:
- VM locking fix"
* tag 'drm-fixes-2019-05-31' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: reserve stollen vram for raven series
drm/etnaviv: lock MMU while dumping core
drm/imx: ipuv3-plane: fix atomic update status query for non-plus i.MX6Q
drm/qxl: drop WARN_ONCE()
drm/amd/display: Don't load DMCU for Raven 1 (v2)
Fix a regression introduced by 70e8a0c71e ("drm/imx: ipuv3-plane: add
function to query atomic update status") that halves the frame rate on
non-plus i.MX6Q, because the pending check always returns "pending"
even if an update is actually applied.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXO5pYxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwDwZAP4oMXmOOAE4ZAB1r/TjPAQ/IK1j
2Jg9EtGdbKn+vPQMJgD/YP5TcdUzOjbbHMnlGV/SAkxpz4+8IvOI/N6XkiEI/gY=
=bJyj
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2019-05-29' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: ipuv3-plane: fix frame rate regression on non-plus i.MX6Q
Fix a regression introduced by 70e8a0c71e ("drm/imx: ipuv3-plane: add
function to query atomic update status") that halves the frame rate on
non-plus i.MX6Q, because the pending check always returns "pending"
even if an update is actually applied.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1559128738.3651.4.camel@pengutronix.de
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 99 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.163048684@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The klocwork static code analyzer complains about using pointer after
being freed, because further we pass it to the gvt_vgpu_err() function.
Assign pointer to be NULL intentionaly, to meet requirements of the code
analyzer.
This patch fixed the issue #648 reported as error by klocwork.
Acked-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Aleksei Gimbitskii <aleksei.gimbitskii@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Static code analyzer warns that index value for scratch_pt may be equal
to -1. Index value type is intel_gvt_gtt_type_t, so it may be any number
at range -1 to 17. Check first if cur_pt_type and cur_pt_type+1 is valid
values.
v2:
- Print some error messages if page table type is invalid. (Colin Xu)
v4:
- Print cur_pt_type in error message. (Colin Xu)
This patch fixed the critial issue #422 reported by klocwork.
Acked-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Aleksei Gimbitskii <aleksei.gimbitskii@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fix the length value of VEB_DI_IECP.
Fixes: be1da7070a ("drm/i915/gvt: vGPU command scanner")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Gao, Fred <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The vgpu ggtt range should be in vgpu aperture or hidden range. This
patch enforce begin and end address check and guarantee both of them are
in the valid range.
For size=0, it will regress to vgpu_gmadr_is_valid(), will refine
this usage in a later fix.
Fixes: 2707e44466 ("drm/i915/gvt: vGPU graphics memory virtualization")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Enter failsafe if vgpu tries to change CSFE_CHICKEN1_REG setting
which is controlled by host.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Enter failsafe if vgpu tries to change GFX_MODE controlled by host.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Host prints below warning message when guest running some application:
"gvt: vgpu(1) Invalid FORCE_NONPRIV write 2754 at 24f0".
"gvt: vgpu(1) Invalid FORCE_NONPRIV write 28a0 at 24f0".
Registers 0x2754 and 0x28a0 are required by guest so add to whitelist.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlzu9swACgkQlvcN/ahK
BwqUOwgAj4S9jbhER39gl+ifvrL8cCc7tq5H5LxSElinu/RMnzKWmdXZ9Z5aiIdq
QLVSe1cg90sad/0zeha4E9HOzKiIOdWMIv++OToIwToAfmpl2DgY0UcUbiqkQEuA
aae3T1E6tDfTYKmqxUhqolE1ZvxmLLVyjV9KOVE4HUuSsLIRr5d8eyrjJPkC/dGY
lKhsHz80oi8X8sPx/CA6Xk1uAVoPCOh4mFPovqOJepl9DnStw8QxeoBzMAqoKBPo
evyI6+HeI3Bh8IyPs1x7NJsNYAbiuAGMuOgKNohPqO+CAIsOLV26fUWwZfpwxBuA
1+x+gckxPeHsKJS6AMcMk8gSyPBk/w==
=6Adp
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-05-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
qxl: Drop WARN when u/s tries to mmap a prime buffer (Gerd)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529211833.GA195708@art_vandelay
our extensions and, thus, the documentation build in general. Who knew
that those deprecation warnings it was outputting actually meant we should
change something? This set of fixes makes the build work again with
Sphinx 2.0 and eliminates the warnings for 1.8. As part of that, we also
need a few fixes to the docs for places where the new Sphinx is more
strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes add
some glue to continue to support versions back to 1.3. We will be adding
some infrastructure soon to nudge users of old versions forward, with the
idea of maybe increasing our minimum version (and removing this glue)
sometime in the future.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzsYw8PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YGuwH+gOk2lGPpI7tsIsctUr3TTviYbu9EywGINUA
c2pPQBHbC13F/QKkb/WArnIhM7eRMWxNy1IlrzqTTLRcAteJihoRNldLVpImxwHJ
DaULovUHRO9uNuVORGV4RLOBUUkrguoz4X7OZooT3tluRZcL58C3Qn8MbZYiZYf1
ZJKHVJxfSedyHYTK1H5qB9uAAvdoNGLjvK8pzA9S7HgHM9viuOlY2GTHn4uvlmI+
qgnbVRNeEb8IRFztvKy2RyMAisx2o5v/lfpKVM+OC9EJgkpw+mw55YUdfDeNavJg
2d3xv8zgS1TP+qAmba2uVwiRDNChTKxz72nbaqZZGOt16StRiyY=
=hrKI
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2-fixes2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"The Sphinx 2.0 release contained a few incompatible API changes that
broke our extensions and, thus, the documentation build in general.
Who knew that those deprecation warnings it was outputting actually
meant we should change something? This set of fixes makes the build
work again with Sphinx 2.0 and eliminates the warnings for 1.8. As
part of that, we also need a few fixes to the docs for places where
the new Sphinx is more strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes
add some glue to continue to support versions back to 1.3. We will be
adding some infrastructure soon to nudge users of old versions
forward, with the idea of maybe increasing our minimum version (and
removing this glue) sometime in the future"
* tag 'docs-5.2-fixes2' of git://git.lwn.net/linux:
drm/i915: Maintain consistent documentation subsection ordering
scripts/sphinx-pre-install: make it handle Sphinx versions
docs: Fix conf.py for Sphinx 2.0
docs: fix multiple doc build warnings in enumeration.rst
lib/list_sort: fix kerneldoc build error
docs: fix numaperf.rst and add it to the doc tree
doc: Cope with the deprecation of AutoReporter
doc: Cope with Sphinx logging deprecations
to avoid screen corruption during modprobe.
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
display hardware clock will not unprepare when
crtc is disable, until crtc is destroyed.
with this patch, hard clock will disable and unprepare
at the same time.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
The devcoredump needs to operate on a stable state of the MMU while
it is writing the MMU state to the coredump. The missing lock
allowed both the userspace submit, as well as the GPU job finish
paths to mutate the MMU state while a coredump is under way.
Fixes: a8c21a5451 (drm/etnaviv: add initial etnaviv DRM driver)
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: David Jander <david@protonic.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
The current buffer check halves the frame rate on non-plus i.MX6Q,
as the IDMAC current buffer pointer is not yet updated when
ipu_plane_atomic_update_pending is called from the EOF irq handler.
Fixes: 70e8a0c71e ("drm/imx: ipuv3-plane: add function to query atomic update status")
Tested-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later". Only the "obvious" versions of these matches are
included here, a number of "non-obvious" variants of text have been
found but those have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOgmlw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4rACfRqxGOGVLR/t6E9dDzOZRAdEz/mYAoJLZmziY
0YlSSSPtP5HI6JDh65Ng
=HXQb
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
-----BEGIN PGP SIGNATURE-----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=4Wu/
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-05-24-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too unusual here for rc2. Except the amdgpu DMCU firmware
loading fix caused build breakage with a different set of Kconfig
options. I've just reverted it for now until the AMD folks can rewrite
it to avoid that problem.
i915:
- boosting fix
- bump ready task fixes
- GVT - reset fix, error return, TRTT handling fix
amdgpu:
- DMCU firmware loading fix
- Polaris 10 pci id for kfd
- picasso screen corruption fix
- SR-IOV fixes
- vega driver reload fixes
- SMU locking fix
- compute profile fix for kfd
vmwgfx:
- integer overflow fixes
- dma sg fix
sun4i:
- HDMI phy fixes
gma500:
- LVDS detection fix
panfrost:
- devfreq selection fix"
* tag 'drm-fixes-2019-05-24-1' of git://anongit.freedesktop.org/drm/drm: (32 commits)
Revert "drm/amd/display: Don't load DMCU for Raven 1"
drm/panfrost: Select devfreq
drm/gma500/cdv: Check vbt config bits when detecting lvds panels
drm/vmwgfx: integer underflow in vmw_cmd_dx_set_shader() leading to an invalid read
drm/vmwgfx: NULL pointer dereference from vmw_cmd_dx_view_define()
drm/vmwgfx: Use the dma scatter-gather iterator to get dma addresses
drm/vmwgfx: Fix compat mode shader operation
drm/vmwgfx: Fix user space handle equal to zero
drm/vmwgfx: Don't send drm sysfs hotplug events on initial master set
drm/i915/gvt: Fix an error code in ppgtt_populate_spt_by_guest_entry()
drm/i915/gvt: do not let TRTTE and 0x4dfc write passthrough to hardware
drm/i915/gvt: add 0x4dfc to gen9 save-restore list
drm/i915/gvt: Tiled Resources mmios are in-context mmios for gen9+
drm/i915/gvt: use cmd to restore in-context mmios to hw for gen9 platform
drm/i915/gvt: emit init breadcrumb for gvt request
drm/amdkfd: Fix compute profile switching
drm/amdgpu: skip fw pri bo alloc for SRIOV
drm/amd/powerplay: fix locking in smu_feature_set_supported()
drm/amdgpu/gmc9: set vram_width properly for SR-IOV
drm/amdgpu/soc15: skip reset on init
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.663497195@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091649.499889647@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
v2: Fix ifdef (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
With Sphinx 2.0 (or prior versions with the deprecation warnings fixed) the
docs build fails with:
Documentation/gpu/i915.rst:403: WARNING: Title level inconsistent:
Global GTT Fence Handling
~~~~~~~~~~~~~~~~~~~~~~~~~
reST markup error:
Documentation/gpu/i915.rst:403: (SEVERE/4) Title level inconsistent:
I "fixed" it by changing the subsections in i915.rst, but that didn't seem
like the correct change. It turns out that a couple of i915 files create
their own subsections in kerneldoc comments using apostrophes as the
heading marker:
Layout
''''''
That breaks the normal subsection marker ordering, and newer Sphinx is
rather more strict about enforcing that ordering. So fix the offending
comments to make Sphinx happy.
(This is unfortunate, in that kerneldoc comments shouldn't need to be aware
of where they might be included in the heading hierarchy, but I don't see
a better way around it).
Cc: stable@vger.kernel.org # v4.14+
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This reverts commit 55143dc23c.
This causes build breakags with some Kconfigs so revert for now.
Fixes: 55143dc23c ("drm/amd/display: Don't load DMCU for Raven 1")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes for 5.2:
- Fix for DMCU firmware issues for stable
- Add missing polaris10 pci id to kfd
- Screen corruption fix on picasso
- Fix for driver reload on vega10
- SR-IOV fixes
- Locking fix in new SMU code
- Compute profile switching fix for KFD
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522205425.3657-1-alexander.deucher@amd.com
- gma500 fix to make lvds detection more reliable
- select devfreq for panfrost since it can't probe without it
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlzlpl0ACgkQlvcN/ahK
Bwp5PAgAnL7n2k7f6ifBhF4h0SLWAGDLNnO1Pmyi5lYQTHSPf66N2xpgatTicMY6
EKVvzsFO3dTFDFbFY3kUC+nuVTaz7NDbPXnVRxiEsIlqoEIII70XHLZJKYdEjkEQ
b2Tueo7lPj6EZjdcOHuErpdd9+Iy4FqPpsNuXz4giBlDU5yVYMgfY/j6EEq7QiSh
N9onTxlSJug/RWtqFx3tGSBxQvLuot+2w3h3i9wIqu/BqjilR1mbmYH9iPULm4wa
CDatEDP3hNSDfQfQTinFpmZR6x29GMGNr4ATBCRCxCupnEofv8eHO1u2cB28sB6s
HQXkBYDaeBIDM3Aozs2A5n89LheG9Q==
=FgtF
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-05-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- sun4i fixes to hdmi phy as well as u16 overflow in dsi (left from -next-fixes)
- gma500 fix to make lvds detection more reliable
- select devfreq for panfrost since it can't probe without it
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190522194440.GA22359@art_vandelay
Currently, there is some logic for the driver to work without devfreq.
However, the driver actually fails to probe if !CONFIG_PM_DEVFREQ.
Fix this by selecting devfreq, and drop the additional checks
for devfreq.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190517150042.776-1-ezequiel@collabora.com
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If SVGA_3D_CMD_DX_SET_SHADER is called with a shader ID
of SVGA3D_INVALID_ID, and a shader type of
SVGA3D_SHADERTYPE_INVALID, the calculated binding.shader_slot
will be 4294967295, leading to an out-of-bounds read in vmw_binding_loc()
when the offset is calculated.
Cc: <stable@vger.kernel.org>
Fixes: d80efd5cb3 ("drm/vmwgfx: Initial DX support")
Signed-off-by: Murray McAllister <murray.mcallister@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
If SVGA_3D_CMD_DX_DEFINE_RENDERTARGET_VIEW is called with a surface
ID of SVGA3D_INVALID_ID, the srf struct will remain NULL after
vmw_cmd_res_check(), leading to a null pointer dereference in
vmw_view_add().
Cc: <stable@vger.kernel.org>
Fixes: d80efd5cb3 ("drm/vmwgfx: Initial DX support")
Signed-off-by: Murray McAllister <murray.mcallister@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Use struct sg_dma_page_iter in favour struct of sg_page_iter, which fairly
recently was declared useless for obtaining dma addresses.
With a struct sg_dma_page_iter we can't call sg_page_iter_page() so
when the page is needed, use the same page lookup mechanism as for the
non-sg dma modes instead of calling sg_dma_page_iter.
Note, the fixes tag doesn't really point to a commit introducing a
failure / regression, but rather to a commit that implemented a simple
workaround for this problem.
Cc: Jason Gunthorpe <jgg@mellanox.com>
Fixes: d901b2760d ("lib/scatterlist: Provide a DMA page iterator")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
In compat mode, we allowed host-backed user-space with guest-backed
kernel / device. In this mode, set shader commands was broken since
no relocations were emitted. Fix this.
Cc: <stable@vger.kernel.org>
Fixes: e8c66efbfe ("drm/vmwgfx: Make user resource lookups reference-free during validation")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
User-space handles equal to zero are interpreted as uninitialized or
illegal by some drm systems (most notably kms). This means that a
dumb buffer or surface with a zero user-space handle can never be
used as a kms frame-buffer.
Cc: <stable@vger.kernel.org>
Fixes: c7eae62666 ("drm/vmwgfx: Make the object handles idr-generated")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
This may confuse user-space clients like plymouth that opens a drm
file descriptor as a result of a hotplug event and then generates a
new event...
Cc: <stable@vger.kernel.org>
Fixes: 5ea1734827 ("drm/vmwgfx: Send a hotplug event at master_set")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
"ret" is uninitialized on this path but it should be -EINVAL.
Fixes: 930c8dfea4 ("drm/i915/gvt: Check if get_next_pt_type() always returns a valid value")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
the vGPU write on TRTTE and 0x4dfc is now write to vreg first. their
values all be restored hardware when context switching.
Fixes: e39c5add32 ("drm/i915/gvt: vGPU MMIO virtualization")
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
0x4dfc is in-context mmio for gen9+, but each vm have different settings
need to add it to save-restore list along with other trtt registers
Fixes: 1786571393 ("drm/i915/gvt: vGPU context switch")
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
for restore-inhibit context, hardware will not load in-context mmios
(engine context part) to hardware, but hardware will save the mmio
values in hardware back to context image. So, in order to save correct
values of vGPU back to context image, values of vGPU mmios have to be
loaded into hardware first for restore-inhibit context.
In this patch, the mechanism is applied to all gen9 platform.
The reason excluding gen8 platforms is only because of lacking of testing
on those platforms.
v3: for mocs registers, goto in-context mmios save-restore path for skl
platform as well (weinan li)
v2: update vreg when scanning indirect context for inhibit context for
gen9
Cc: Weinan Li <weinan.z.li@intel.com>
Acked-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
"To track whether a request has started on HW, we can emit a breadcrumb at
the beginning of the request and check its timeline's HWSP to see if the
breadcrumb has advanced past the start of this request." It means all the
request which timeline's has_init_breadcrumb is true, then the
emit_init_breadcrumb process must have before emitting the real commands,
otherwise, the scheduler might get a wrong state of this request during
reset. If the request is exactly the guilty one, the scheduler won't
terminate it with the wrong state. To avoid this, do emit_init_breadcrumb
for all the requests from gvt.
v2: cc to stable kernel
Fixes: 8547444137 ("drm/i915: Identify active requests")
Cc: stable@vger.kernel.org
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fix compute profile switching on process termination.
Add a dedicated reference counter to keep track of entry/exit to/from
compute profile. This enables switching compute profiles for other
reasons than process creation or termination.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PSP fw primary buffer is not used under SRIOV.
Under SRIOV, VBIOS or hypervisor driver will load psp
sos and psp sysdrv. Therefore, we don't need to
allocate memory for it.
v2: remove superfluous check for amdgpu_bo_free_kernel().
Signed-off-by: Yintian Tao <yttao@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a typo so the code unlocks twice instead of taking the lock and
then releasing it.
Fixes: f14a323db5 ("drm/amd/powerplay: implement update enabled feature state to smc for smu11")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SR-IOV, vram_width can't be read from ATOM as
RAVEN, and DF related registers is not readable, so hardcord
is the only way to set the correct vram_width.
Reviewed-by: Yintian Tao <yttao@amd.com>
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Yintian Tao <yttao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not necessary on soc15 and breaks driver reload on server cards.
Acked-by: Amber Lin <Amber.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This was added to amdgpu but was missed in amdkfd
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.rg
[WHY]
Some early Raven boards had a bad SBIOS that doesn't play nicely with
the DMCU FW. We thought the issues were fixed by ignoring errors on DMCU
load but that doesn't seem to be the case. We've still seen reports of
users unable to boot their systems at all.
[HOW]
Disable DMCU load on Raven 1. Only load it for Raven 2 and Picasso.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY]
We only want to load DMCU FW on Picasso and Raven 2, not on Raven 1.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
In commit b7404c7ecb ("drm/i915: Bump ready tasks ahead of
busywaits"), I tried cutting a corner in order to not install a signal
for each of our dependencies, and only listened to requests on which we
were intending to busywait. The compromise that was made was that
instead of then being able to promote the request with a full
NOSEMAPHORE like its non-busywaiting brethren, as we had not ensured we
had cleared the semaphore chain, we settled for only using the NEWCLIENT
boost. With an over saturated system with multiple NEWCLIENTS in flight
at any time, this was found to be an inadequate promotion and left us
with a much poorer scheduling order than prior to using semaphores.
The outcome of this patch, is that all requests have NOSEMAPHORE
priority when they have no dependencies and are ready to run and not
busywait, restoring the pre-semaphore ordering on saturated systems.
We can demonstrate the effect of poor scheduling order by oversaturating
the system using gem_wsim on a system with multiple vcs engines
(i.e running the same workloads across more clients than required for
peak throughput, e.g. media_load_balance_17i7.wsim -c4 -b context):
x v5.1 (normalized)
+ tip
* fix
+------------------------------------------------------------------------+
| x |
| x |
| x |
| x |
| %x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %%x |
| %#x |
| %#x |
| %#x |
| %#x |
| %#x |
| + %#xx |
| + %#xx |
| + %%#xx |
| + %%#xx |
| + %%#xx |
| + %%#xx |
| + %%##x |
| +++ %%##x |
| +++ %%##x |
| +++ %%##x |
| ++++ %%##x |
| ++++ %%##x |
| ++++ %%##xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ %###xx |
| ++++ + %#O#xx |
| ++++ + %#O#xx |
| ++++++ + %#O#xx |
| ++++++++++ %OOOxxx|
| ++++++++++ + %#OOO#xx|
| + ++++++++++++ ++ +++++ + ++ @@OOOO#xx|
| |A_| |
||__________M_______A____________________| |
| |A_| |
+------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 120 0.99456 1.00628 0.999985 1.0001545 0.0024387139
+ 120 0.873021 1.00037 0.884134 0.90148752 0.039190862
Difference at 99.5% confidence
-0.098667 +/- 0.0110762
-9.86517% +/- 1.10745%
(Student's t, pooled s = 0.0277657)
% 120 0.990207 1.00165 0.9970265 0.99699748 0.0021024
Difference at 99.5% confidence
-0.003157 +/- 0.000908245
-0.315651% +/- 0.0908105%
(Student's t, pooled s = 0.00227678)
Fixes: b7404c7ecb ("drm/i915: Bump ready tasks ahead of busywaits")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-2-chris@chris-wilson.co.uk
(cherry picked from commit 17db337f50)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Commit 1413b2bc07 ("drm/i915: Trim NEWCLIENT boosting") had the
intended consequence of not allowing a sequence of work that merely
crossed into a new engine the privilege to be promoted to NEWCLIENT
status. It also had the unintended consequence of actually making
NEWCLIENT effective on heavily oversubscribed transcode machines and
impacting upon their throughput.
If we consider a client packet composed of (rcsA, rcsB, vcs) and 30 of
those clients, using the NEWCLIENT boost that will be scheduled as
rcsA x 30, (rcsB, vcs) x 30
where as before it would have been
(rcsA, rcsB, vcs) x 30
That is with NEWCLIENT only boosting the first request of each client,
we would execute all rcsA requests prior to running on the vcs engines;
acruing a lot of dead time as compared to the previous case where the
vcs engine would be started in parallel to processing the second client.
The previous patch has the effect of delaying submission until it is
required by a third party (either the user with an explicit wait, or by
another client/engine). We reduce the NEWCLIENT bump to a mere WAIT,
which has the effect of removing its preemptive grant and reducing it to
the same level as any other user interaction -- that it will not be
promoted above the interengine dependencies, and so preventing NEWCLIENTS
from starving other engines. This a large nerf to the rrul properties of
the current NEWCLIENT, but it still does give prioritised submission to
new requests from light workloads.
References: b16c765122 ("drm/i915: Priority boost for new clients")
Fixes: 1413b2bc07 ("drm/i915: Trim NEWCLIENT boosting") # customer impact
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-4-chris@chris-wilson.co.uk
(cherry picked from commit 68fc728b01)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The handling of the no-preemption priority level imposes the restriction
that we need to maintain the implied ordering even though preemption is
disabled. Otherwise we may end up with an AB-BA deadlock across multiple
engine due to a real preemption event reordering the no-preemption
WAITs. To resolve this issue we currently promote all requests to WAIT
on unsubmission, however this interferes with the timeslicing
requirement that we do not apply any implicit promotion that will defeat
the round-robin timeslice list. (If we automatically promote the active
request it will go back to the head of the queue and not the tail!)
So we need implicit promotion to prevent reordering around semaphores
where we are not allowed to preempt, and we must avoid implicit
promotion on unsubmission. So instead of at unsubmit, if we apply that
implicit promotion on adding the dependency, we avoid the semaphore
deadlock and we also reduce the gains made by the promotion for user
space waiting. Furthermore, by keeping the earlier dependencies at a
higher level, we reduce the search space for timeslicing without
altering runtime scheduling too badly (no dependencies at all will be
assigned a higher priority for rrul).
v2: Limit the bump to external edges (as originally intended) i.e.
between contexts and out to the user.
Testcase: igt/gem_concurrent_blit
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-3-chris@chris-wilson.co.uk
(cherry picked from commit 6e7eb7a807)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
To simplify the next patch, update bump_priority and schedule to accept
the internal i915_sched_ndoe directly and not expect a request pointer.
add/remove: 0/0 grow/shrink: 2/1 up/down: 8/-15 (-7)
Function old new delta
i915_schedule_bump_priority 109 113 +4
i915_schedule 50 54 +4
__i915_schedule 922 907 -15
v2: Adopt node for the old rq local, since it no longer is a request but
the origin node.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-2-chris@chris-wilson.co.uk
(cherry picked from commit 52c76fb18a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
To avoid pulling in a forward declaration in the next patch, move the
i915_sched_node handling to after the main dfs of the scheduler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-1-chris@chris-wilson.co.uk
(cherry picked from commit 5ae87063c1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
patches so we can merge them into -fixes.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlziwSIACgkQlvcN/ahK
BwrfMgf/egFs+Z6oNAlKgadIiy+qd8Yp4DrQHYssdV2ToxCBDiOpTrxeC92gFcqD
TNVUpLRg0XoDcVm81HriOMfmK9uUsOreFY2WoER1hKgeiv1QNpO8AO6rzF4aykY6
nn8PP0N4QS3En/bwqxDr8S9mnXzxkBjYk6j/Kn7kEXfsH2nI9RxIl9zBhLirsYBq
GOj01tsdbTPZBaDg0p0A0ZUzlqoyZInMPkri+pCiAgF2w6mo1n3Z/y45uGpboMFn
daGJjdZCoRtHaBo5naqLQ4Osx075oqZaguGaAT+BNb3QaulBDeKCA0Bu201iqWwD
INBD+Bh/6Q9MdV8vzc3VLwLJFlDj0A==
=ZyUW
-----END PGP SIGNATURE-----
Merge drm-misc-next-fixes-2019-05-20 into drm-misc-fixes
Picking up 3 sun4i patches that missed the last drm-misc-next-fixes pull
request for 5.2
Signed-off-by: Sean Paul <seanpaul@chromium.org>
include when we had clk_readl() and clk_writel(), but those are gone now
so this patch pushes the dependency out to the users of clk-provider.h.
-----BEGIN PGP SIGNATURE-----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=JjQo
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk framework updates from Stephen Boyd:
"One more patch to remove io.h from clk-provider.h.
We used to need this include when we had clk_readl() and clk_writel(),
but those are gone now so this patch pushes the dependency out to the
users of clk-provider.h"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Remove io.h from clk-provider.h
-----BEGIN PGP SIGNATURE-----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=EfK4
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"A bunch of fixes for the merge window closure, doesn't seem to be
anything too major or serious in there.
It does add TU117 turing modesetting to nouveau but it's just an
enable for preexisting code.
amdgpu:
- gpu reset at load crash fix
- ATPX hotplug fix for when dGPU is off
- SR-IOV fixes
radeon:
- r5xx pll fixes
i915:
- GVT (MCHBAR, buffer alignment, misc warnings fixes)
- Fixes for newly enabled semaphore code
- Geminilake disable framebuffer compression
- HSW edp fast modeset fix
- IRQ vs RCU race fix
nouveau:
- Turing modesetting fixes
- TU117 support
msm:
- SDM845 bringup fixes
panfrost:
- static checker fixes
pl111:
- spinlock init fix.
bridge:
- refresh rate register fix for adv7511"
* tag 'drm-next-2019-05-16' of git://anongit.freedesktop.org/drm/drm: (36 commits)
drm/msm: Upgrade gxpd checks to IS_ERR_OR_NULL
drm/msm/dpu: Remove duplicate header
drm/pl111: Initialize clock spinlock early
drm/msm: correct attempted NULL pointer dereference in debugfs
drm/msm: remove resv fields from msm_gem_object struct
drm/nouveau: fix duplication of nv50_head_atom struct
drm/nouveau/disp/dp: respect sink limits when selecting failsafe link configuration
drm/nouveau/core: initial support for boards with TU117 chipset
drm/nouveau/core: allow detected chipset to be overridden
drm/nouveau/kms/gf119-gp10x: push HeadSetControlOutputResource() mthd when encoders change
drm/nouveau/kms/nv50-: fix bug preventing non-vsync'd page flips
drm/nouveau/kms/gv100-: fix spurious window immediate interlocks
drm/bridge: adv7511: Fix low refresh rate selection
drm/panfrost: Add missing _fini() calls in panfrost_device_fini()
drm/panfrost: Only put sync_out if non-NULL
drm/i915: Seal races between async GPU cancellation, retirement and signaling
drm/i915: Fix fastset vs. pfit on/off on HSW EDP transcoder
drm/i915/fbc: disable framebuffer compression on GeminiLake
drm/amdgpu/psp: move psp version specific function pointers to early_init
drm/radeon: prefer lower reference dividers
...
Loop N1 instruction delay for burst mode devices are computed
based on horizontal sync and porch timing values.
The current driver is using u16 type for computing this hsync_porch
value, which would failed to fit within the u16 type for large sync
and porch timings devices. This would result in hsync_porch overflow
and eventually computed wrong instruction delay value.
Example, timings, where it produces the overflow
{
.hdisplay = 1080,
.hsync_start = 1080 + 408,
.hsync_end = 1080 + 408 + 4,
.htotal = 1080 + 408 + 4 + 38,
}
It reproduces the desired delay value 65487 but the correct working
value should be 7.
So, Fix it by computing hsync_porch value separately with u32 type.
Fixes: 1c1a7aa366 ("drm/sun4i: dsi: Add burst support")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190512184128.13720-2-jagan@amarulasolutions.com
Current code initializes HDMI PHY clock driver before reset line is
deasserted and clocks enabled. Because of that, initial readout of
clock divider is incorrect (0 instead of 2). This causes any clock
rate with divider 1 (register value 0) to be set incorrectly.
Fix this by moving initialization of HDMI PHY clock driver after reset
line is deasserted and clocks enabled.
Cc: stable@vger.kernel.org # 4.17+
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190514204337.11068-2-jernej.skrabec@siol.net
- Fix the low refresh rate register in adv7511
- A handful of msm fixes that fell out of 5.1 bringup on SDM845
- Fix spinlock initialization in pl111
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlzccqQACgkQlvcN/ahK
Bwojowf/fzcPku4y1L8IzPIoQ75iYr7VC4jhHiTN1DxHHVQUCCMpdPk9EPMJUPY3
OeMmOqirtOL4+QK+5z/3Zp8ERJ+NYz93Hgkc3GNlNGwt12odr1mavRWNmhPRNx0t
Ghj3nFDRI9MuK6rK3Hzc+Kap5vTFwD3bAEaCt3eRGlnf0yTzqwer969GsaKCeMeo
XqSI3ZtJq2T6bxpvwgKbRNHWxnEGtW/wI7newfz0I3BIVIbciTPz564kNmXiba8R
mC8CG2WB860hxT4AZkFoKTP8IalfskL9XPrLKOmpYocPxPDSwBz6lHQzOJlvk52d
OjQrcmD3URs5j3xSVmMvoPrT05fTYQ==
=dZYN
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2019-05-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- A couple new panfrost fixes
- Fix the low refresh rate register in adv7511
- A handful of msm fixes that fell out of 5.1 bringup on SDM845
- Fix spinlock initialization in pl111
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515201729.GA89093@art_vandelay
dev_pm_domain_attach_by_name() can return NULL, so we should check for
that case when we're about to dereference gxpd.
Fixes: 9325d4266a ("drm/msm/gpu: Attach to the GPU GX power domain")
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515170104.155525-1-sean@poorly.run
