Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Section Y.7.4 Actions on receipt of proactive RANN, an individually
addressed PREQ should be generated towards the neighbor peer mesh STA indicated
in the RANN Sender Address field in the forwarding information.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The association sequence looks (roughly) like
this now:
* set BSSID
* set station to EXIST state
* send auth
* set station to AUTH state
* send assoc
* set station to ASSOC state
* set BSS info to associated
In contrast, the deauth/disassoc sequence is
the other way around:
* clear BSSID/BSS info state
* remove station
* send deauth/disassoc
(in some cases the last two steps are reversed.)
This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
* send deauth/disassoc
* flush
* remove station
* clear BSSID/BSS info state
At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The major features of this series are:
- making RCU more aggressive about entering dyntick-idle mode in order to
improve energy efficiency
- converting a few more call_rcu()s to kfree_rcu()s
- applying a number of rcutree fixes and cleanups to rcutiny
- removing CONFIG_SMP #ifdefs from treercu
- allowing RCU CPU stall times to be set via sysfs
- adding CPU-stall capability to rcutorture
- adding more RCU-abuse diagnostics
- updating documentation
- fixing yet more issues located by the still-ongoing top-to-bottom
inspection of RCU, this time with a special focus on the
CPU-hotplug code path.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad reports that if a scan finishes in the
middle of processing associated (however it
happens), the interface can go idle. This is
because we set assoc_data to NULL before we
set associated. Change the order so any idle
check will find either one of them.
Doing this requires duplicating the TX sync
processing, but I already have a patch to
delete that completely and will submit that
as soon as my driver changes to no longer
require it are submitted.
Reported-by: Eliad Peller <eliad@wizery.com>
Tested-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_restart_sta_timer() takes care for enqueueing
monitor_work if needed, so no need to do it again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that monitor the connection in the hw don't need
the monitor work in the driver.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: stable@vger.kernel.org
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call_rcu() in mesh_gate_del() invokes mesh_gate_node_reclaim(),
which simply calls kfree(). So convert the call_rcu() to kfree_rcu(),
allowing mesh_gate_node_reclaim() to be eliminated.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
[<8137b9df>] rwlock_bug+0x3d/0x47
[<81179830>] do_raw_read_lock+0x19/0x29
[<8137f063>] _raw_read_lock+0xd/0xf
[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
[<812dc0c9>] __dev_change_flags+0x9c/0x113
[<812dc1ae>] dev_change_flags+0x18/0x44
[<8132144f>] devinet_ioctl+0x243/0x51a
[<81321ba9>] inet_ioctl+0x93/0xac
[<812cc951>] sock_ioctl+0x1c6/0x1ea
[<812cc78b>] ? might_fault+0x20/0x20
[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
[<810a6ebb>] ? fget_light+0x2f/0x70
[<812ce549>] ? sys_recvmsg+0x3e/0x48
[<810b1f35>] sys_ioctl+0x46/0x69
[<8137fa77>] sysenter_do_call+0x12/0x2
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you want to use mesh support from mac80211 on a recent
kernel on 2.6.24 you'll run into a name clash when compiling
against include/linux/namei.h, so rename this routine.
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c: At top level:
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c:342:26: error: conflicting types for ‘path_lookup’
include/linux/namei.h:71:12: note: previous declaration of ‘path_lookup’ was here
Although this could sit as a separate patch in compat-wireless it seems
best to just merge upstream.
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@frijolero.org>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not debugging mac80211 code, station state transitions do not need to
show up in the kernel log.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dummy STA support was added because I didn't
want to change the driver API at the time. Now
that we have state transitions triggering station
add/remove in the driver, we only call add once a
station reaches ASSOCIATED, so we can remove the
dummy station stuff again.
While at it, tighten the RX check and accept only
port control (EAP) frames from the AP station if
it's not associated yet -- in other cases there's
no race.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of maintaining separate sta_add/sta_remove
callsites, implement it in sta_state when the driver
has no sta_state implementation.
The only behavioural change this should cause is in
secure mesh mode: with this the station entries will
only be created after the stations are set to AUTH.
Given which drivers support mesh, this seems to not
be a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by drivers later if they
need to have stations inserted all the time,
in mac80211 has no purpose, is never used
and sta_state starts out in NONE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station couldn't be uploaded to the driver but
is still kept (only in IBSS mode) we still shouldn't
try to program the keys for it into hardware; fix
this bug by skipping the key upload in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting keys and updating TKIP keys must use the
BSS sdata (not AP_VLAN), so we translate. Move
the translation into driver-ops wrappers instead
of having it inline in the code to simplify the
normal code flow.
The same can be done for sta_add/remove which
already does the translation in the wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the station state modification right before insert,
this just makes the current code more readable (you can
tell that it's before insertion looking at a single
screenful of code) right now, but some upcoming changes
will require this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code checks for stored_mpdu_num > 1, causing
the reorder_timer to be triggered indefinitely, but the
frame is never timed-out (until the next packet is received)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Cc: <stable@vger.kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unted the assumption that the sta struct is still accessible before the
synchronize_rcu call we should move the num_sta_ps counter decrement
after synchronize_rcu to avoid incorrect decrements if num_sta_ps.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver blocked this specific STA with the help of
ieee80211_sta_block_awake we won't clear WLAN_STA_PS_STA later but
still decrement num_sta_ps. Hence, the next data frame from this
STA will trigger ap_sta_ps_end again and also decrement num_sta_ps
again leading to an incorrect num_sta_ps counter.
This can result in problems with powersaving clients not waking up
from PS because the TIM calculation might be skipped due to the
incorrect num_sta_ps counter.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN_STA_PS_DRIVER is set by ieee80211_sta_block_awake the
num_sta_ps counter is not incremented. Hence, we shouldn't decrement
it in __sta_info_destroy if only WLAN_STA_PS_DRIVER is set. This
could result in an incorrect num_sta_ps counter leading to strange side
effects with associated powersaving clients.
Fix this by only decrementing num_sta_ps when WLAN_STA_PS_STA was set
before.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f1e3be1561.
Johannes Berg <johannes@sipsolutions.net> thinks that this patch is
incorrect. I'll defer to his judgment.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_recalc_idle() iterates through the vifs,
sets bss_conf.idle = true if they are disconnected,
and increases "count" if they are not (which later
gets evaluated in order to determine whether the
device is idle).
However, the loop doesn't set bss_conf.idle = false
(along with increasing "count"), causing the device
idle state and the vif idle state to get out of sync
in some cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 13c40c5 ("mac80211: Add HT operation modes for IBSS") broke
ibss operation by mistakenly removing the local->oper_channel
update (causing ibss to start on the wrong channel). fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh's patch to destroy aggregation sessions when
stations are destroyed was needed, but unnecessarily
complex. Clean up this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Actually the DA field has already been checked along the rx path (in
prepare_for_handlers()) and this check is therefore useless at this point.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When deauth is requested while an auth or assoc
work item is in progress, we currently delete it
without regard for any state it might need to
clean up. Fix it by cleaning up for those items.
In the case Pontus found, the problem manifested
itself as such:
authenticate with 00:23:69:aa:dd:7b (try 1)
authenticated
failed to insert Dummy STA entry for the AP (error -17)
deauthenticating from 00:23:69:aa:dd:7b by local choice (reason=2)
It could also happen differently if the driver
uses the tx_sync callback.
We can't just call the ->done() method of the work
items because that will lock up due to the locking
in cfg80211. This fix isn't very clean, but that
seems acceptable since I have patches pending to
remove this code completely.
Cc: stable@vger.kernel.org
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Tested-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local->tx_headroom instad of local->hw.extra_tx_headroom.
local->tx_headroom is the max of hw.extra_tx_headroom required by the
driver and the headroom required by mac80211 for status reporting. On
drivers where hw.extra_tx_headroom is smaller than what mac80211
requires (e.g. ath5k), we would not reserve sufficient buffer space to
report tx status.
Also, don't reserve local->tx_headroom + local->hw.extra_tx_headroom.
Reported-by: Simon Morgenthaler <s.morgenthaler@students.unibe.ch>
Reported-by: Kai Scharwies <kai@scharwies.de>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since stations moved into a virtual interface
subdirectory, this link has been broken. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other code paths in sta_unblock synchronize with the network
softirq by using local_bh_disable/enable. Do the same around
ieee80211_sta_ps_deliver_wakeup.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function ieee80211_tx_h_encrypt the var info was
initialized from tx->skb, since the fucntion
is called after the function ieee80211_tx_h_fragment
tx->skb is not valid anymore.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may leak the 'fwd_skb' we skb_copy() in ieee80211_rx_h_mesh_fwding() if
we take the 'else' branch in the 'if' statement just below. If we take
that branch we'll end up returning from the function and since we've not
assigned 'fwd_skb' to anything at that point, we leak it when the variable
goes out of scope.
The simple fix seems to be to just kfree_skb(fwd_skb); just before we
return. That is what this patch does.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace attempts to authorize a station
that is already authorized, nothing happens as
you'd expect. Similarly, when it unauthorizes
a station that is associated, nothing happens.
However, when it unauthorizes a station that
isn't even associated yet, we erroneously try
to move the station to associated. This seems
to happen occasionally as a result of a race
when wpa_supplicant attempts to unauthorize
the port in managed mode. Particularly with my
new patches to keep stations, it can then move
a station into ASSOCIATED state before we have
really associated, which is really confusing.
I introduced this bug in
"mac80211: refactor station state transitions"
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since:
commit 816c04fe7e
Author: Christian Lamparter <chunkeey@googlemail.com>
Date: Sat Apr 30 15:24:30 2011 +0200
mac80211: consolidate MIC failure report handling
is possible to that we dereference rx->key == NULL when driver set
RX_FLAG_MMIC_STRIPPED and not RX_FLAG_IV_STRIPPED and we are in
promiscuous mode. This happen with rt73usb and rt61pci at least.
Before the commit we always check rx->key against NULL, so I assume
fix should be done in mac80211 (also mic_fail path has similar check).
References:
https://bugzilla.redhat.com/show_bug.cgi?id=769766http://rt2x00.serialmonkey.com/pipermail/users_rt2x00.serialmonkey.com/2012-January/004395.html
Cc: stable@vger.kernel.org # 3.0+
Reported-by: Stuart D Gathman <stuart@gathman.org>
Reported-by: Kai Wohlfahrt <kai.scorpio@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_offchannel_enable_all_ps function is no longer used
and looks like its logic is extensively handled in
ieee80211_offchannel_stop_vifs
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ideally, hardware/firmware initialization is complete after the
drv_start routine. In mac80211 restart code (ieee80211_reconfig),
defer calling the driver commands i.e. setup fragmentation
threshold, rts threshold and coverage class till drv_start
routine is called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
v2: Removed extra blank line added.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this is being recently introduced by the commit
a85e1d5597
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when we run high bandwidth UDP traffic and we trigger a scan, the scan
state machine seems to be looping in SUSPEND->RESUME->DECISION->SUSPEND
and SET_CHANNEL seems to be never called as 'tx_empty' is never true
while running UDP traffic. fix this by settting SET_CHANNEL state when
we get into RESUME state.
Cc: Leela Kella <leela@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the vif is stopped while it is offchannel (e.g. right
after p2p negotiation) the SDATA_STATE_OFFCHANNEL flag
is never get cleared, resulting in various bad effects
(e.g. GO can't start beaconing).
Fix it by clearing the SDATA_STATE_OFFCHANNEL flag
even if the vif is stopped.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to not serve any purpose anymore, at least all frame
processing afterwards seems to be able to deal with QoS frames. So,
let's save the expensive memmove and just leave the QoS header in the
802.11 frame for further processing.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 relays a frame from STA1 to STA2 in AP mode it will get
re-classified in the tx path. Unfortunately the frame protocol field
is always set to ETH_P_8023 while the classification only kicks in
for ETH_P_IP. Hence, a high priority frame from STA1 will be send to
STA2 as best effort.
Instead of running classification on the frame just use the same
priority as STA1 did. Do this by adding 256 to the skb->priority
to allow cfg80211_classify8021d to shortcut frame classification.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS merge code calls ieee80211_sta_expire() with a relatively
short expire timeout that purges other clients prematurely. The
expire function has to check that only the clients belonging to
the vif in question are purged.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 42624d4913
created following sparse warning
>net/mac80211/sta_info.c:965:24: warning: incorrect type in assignment (different address spaces)
>net/mac80211/sta_info.c:965:24: expected struct tid_ampdu_tx *tid_tx
>net/mac80211/sta_info.c:965:24: got struct tid_ampdu_tx [noderef] <asn:4>*<noident>
Making use of rcu_dereference_protected to fix the problem.
V2:
- Replacing rcu_dereference with rcu_dereference_protected
as suggested by Johannes.
- Adding mutex_lock/unlock to satisfy the condition at
rcu_dereference_protected
Cc: Nishant Sarmukadam <nishants@marvell.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a peer changes SMPS state we should update
rate control so it doesn't have to detect it by
itself. It can't detect "dynamic" mode anyway
since that just requires rts-cts handshaking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently code allows three (HT_AGG_MAX_RETRIES) unanswered addba
requests. When this limit is reached aggregation is turned off for
given TID permanently. This doesn't seem right: three requests is
not that much, some 'blackout' can happen, but effect of it affects
whole connection indefinitely.
This patch increases number of retries to 15. Also, when there have
been 3 or more retries it splits further retries apart by 15 seconds
instead of sending them in very short period of time.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we found that power save is not getting enabled when we do
change interface in this order STA->IBSS->STA. this is
because ieee80211_setup_sdata clears type-dependent union
Reported-by: Leela Kella <leela@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently BAR, ADDBA and DELBA frames are always sent using AC_VO. If
the TID for which a BA session is established is assigned to a different
queue BAR, ADDBA and DELBA frames can "overtake" frames of the according
BA session.
Hence, always put BA session related frames into the same queue as the
BA sessions data frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that IBSS no longer needs to insert stations
from atomic context, we can get rid of all the
special cases for that, and even get rid of the
sta_lock (though it needs to stay as tim_lock.)
This makes the station management code much more
straight-forward.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to notify drivers and simplify the station
management code, defer IBSS station insertion to a
work item and don't do it directly while receiving
a frame.
This increases the complexity in IBSS a little bit,
but it's pretty straight forward and it allows us
to reduce the station management complexity (next
patch) considerably.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No real changes, just note that they are const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, each AP interface will send multicast
traffic if any interface has a station entry even
if that station entry is allocated only. With the
new station state management we can easily fix it
by adding a counter that counts each authorized
station only and send multicast traffic only when
the correct interface has at least one authorized
station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>