As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA7 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 2 gpio keys wired through TS_LCD_GPIO3, TS_LCD_GPIO4
which in turn connected to PCF8575 GPIO pcf_lcd: gpio@20 expander
pins 2 and 3.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 4 user gpio leds connected to PCF8575 GPIO pcf_lcd:
gpio@20 expander pins [4,5,6,7], so add corresponding DT nodes.
Do not enable any triggers by default as not all of them are proved
to work on -RT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT definition for CF8575 GPIO pcf_lcd: gpio@20
expander which is connected to i2c bus 1 and has slave address 0x20.
It allows to control:
- tc_lcd gpios, pins p0-p3
- user leds, pins p4-p7
- control LCD panel power, p15
PCF8575 GPIO pcf_lcd: gpio@20 expander supports interrupt controller
functionality and its INT line is connected to dra7 GPIO6.11 pin.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This GPIO expander is used for controlling various muxes on the board.
By default select audio functionality over VIN6 by setting the P1
(vin6_sel_s0) pin to low.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS77018DBVT is used to create 1.8V from avm_3v3_sw's 3.3V connected to
aic3106's DVDD.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the name for the supply as it is in the schematics since the same
supply is used for other peripherals than MMC2, like audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fix it by making ldo1_reg as always_on.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SDMMC Card Detect can be used over default GPIO map.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a node for evm_3v3_sd using onboard pcf GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.
Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
data instead of platform data from Eliad Peller <eliad@wizery.com>:
- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.
- Update the current users to use the bindings instead of pdata-quirks.
- Finally, remove the deprecated wl12xx_platform_data struct
Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.
As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nr1k
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:
Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:
- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.
- Update the current users to use the bindings instead of pdata-quirks.
- Finally, remove the deprecated wl12xx_platform_data struct
Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.
As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.
* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
wlcore: remove wl12xx_platform_data
ARM: dts: add wl12xx/wl18xx bindings
wlcore: add device-tree support
dt: bindings: add TI's wilink wireless device
wl12xx: use frequency instead of enumerations for pdata clocks
wlcore: set irq_trigger in board files instead of hiding behind a quirk
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
64KiB is allocated for qspi dtb partition which is not
sufficient, so updating the partition table size to 512KiB
for device tree partition.
This also aligns the QSPI partition definitions between
kernel and U-Boot.
Fixes: dc2dd5b8 ("ARM: dts: dra7: Add qspi device")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest Data Manual, for newer samples,
the nominal voltage required for VDD_CORE at OPP_NOM can be
upto 1.06V which was 1.03V earlier.
Update the regulator max voltage constraint for SMPS7,
connected to VDD_CORE, to meet this requirement.
Document reference:
DRA74 Data Manual, SPRS857M - Dec 2012, Revised Oct 2014.
DRA72 Data Manual, SPRS906G - Dec 2012, revised Oct 2014.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The max expected voltage for VDD_GPU, connected to SMPS6, is 1.25V.
Correct regulator max voltage constraint to meet this requirement.
Document reference: DRA74 Data Manual, SPRS857M - Dec 2012,
Revised Oct 2014.
Fixes: c56a831ca4 ("ARM: dts: DRA7: Add TPS659038 PMIC nodes")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.
WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.
The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2Sq1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, this is the largest branch, though this time a little under
half of the total changes with 307 individual non-merge changesets.
The largest changes are the addition of new machines, in particular
the Tegra based Chromebook, the Renesas r8a7794 SoC, and DT support
for the old i.MX1 platform.
Other changes include
- at91: various sam9 and sama5 updates
- exynos: much extended Peach Pi/Pit (Chromebook 2) support
- keystone: new peripherals
- meson: added DT for meson6 SoC
- mvebu: new device support for Armada 370/375
- qcom: improved support for IPQ8064 and MSM8x60
- rockchip: much improved support for rk3288
- shmobile: lots of updates all over the place
- sunxi: dts license change
- sunxi: more a23 device support
- vexpress: CLCD DT description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (308 commits)
ARM: DTS: meson: update DTSI to add watchdog node
ARM: dts: keystone-k2l: fix mdio io start address
ARM: dts: keystone-k2e: fix mdio io start address
ARM: dts: keystone-k2e: update usb1 node for dma properties
ARM: dts: keystone: fix io range for usb_phy0
Revert "Merge tag 'hix5hd2-dt-for-3.18' of git://github.com/hisilicon/linux-hisi into next/dt"
Revert "ARM: dts: hix5hd2: add wdg node"
ARM: dts: add rk3288 i2s controller
ARM: vexpress: Add CLCD Device Tree properties
ARM: bcm2835: add I2S pinctrl to device tree
ARM: meson: documentation: add bindings documentation
ARM: meson: dts: add basic Meson/Meson6/Meson6-atv1200 DTSI/DTS
ARM: dts: mt6589: Change compatible string for GIC
ARM: dts: mediatek: Add compatible property for aquaris5
ARM: dts: mt6589-aquaris5: Add boot argument earlyprintk
ARM: dts: mt6589: Fix typo in GIC unit address
ARM: dts: Build dtb for Mediatek board
ARM: dts: keystone: fix bindings for pcie and usb clock nodes
ARM: dts: keystone: k2l: Fix chip selects for SPI devices
ARM: dts: keystone: add dsp gpio controllers nodes
...
The nand timings were scaled down by 2 to account for
the 2x rate returned by clk_get_rate(gpmc_fclk).
As the clock data got fixed by [1], revert back to actual
timings (i.e. scale them up by 2).
Without this NAND doesn't work on dra7-evm.
[1] - commit dd94324b98
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Fixes: ff66a3c86e ("ARM: dts: dra7: add support for parallel NAND flash")
Cc: <stable@vger.kernel.org> [3.16]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mark rxd as wakeupcapable for 115200n8 no hardware-flow control
configuration. If h/w flow control is being used, then rts/cts
appropriately should be used.
Signed-off-by: Nishanth Menon <nm@ti.com>
DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).
Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Document and use new cadence serial binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlPI73sACgkQykllyylKDCGYzQCggc3g80f6R008+SNKlrN0Wuy+
b9kAnjqTO0Q0kDf4PlI/a5EVsfPmOzoS
=Bo6W
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
The ldousb_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7xx platform has in-build GPMC and ELM h/w engines which can be used
for accessing externel NAND flash device. This patch:
- adds generic DT binding in dra7.dtsi for enabling GPMC and ELM h/w engines
- adds DT binding for Micron NAND Flash (MT29F2G16AADWP) present on dra7-evm
*Important*
On DRA7 EVM, GPMC_WPN and NAND_BOOTn are controlled by DIP switch
So following board settings are required for NAND device detection:
SW5.9 (GPMC_WPN) = LOW
SW5.1 (NAND_BOOTn) = HIGH
Signed-off-by: Minal Shah <minalkshah@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB pinmux information and USB modes
for the USB controllers.
CC: BenoƮt Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These add device tree entry for qspi controller driver on dra7-evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA722 is part of DRA72x family which are single core cortex A15 devices
with most infrastructure IPs otherwise same as whats on the DRA74x family.
So move the cpu nodes into dra74x.dtsi and dra72x.dtsi respectively.
Also add a minimal dra72-evm dts file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: linux-doc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>
"ti,dra752" is neither documented nor correct, since the device is actually a
dra742 device as rightly documented in dt bindings.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT nodes for TPS659038 PMIC on DRA7 boards.
It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>