In a crosslink configuration doorbells and messages largely work the
same but the NTB registers must be accessed through the reserved LUT
window. Also, as a bonus, seeing there are now two independent sets of
NTB links, both partitions can actually use all 60 doorbell registers
instead of them having to be split into two for each partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Crosslink is a feature of the Switchtec switches that is similar to
the B2B mode of other NTB devices. It allows a system to be designed
that is perfectly symmetric with two identical switches that link
two hosts together.
In order for the system to be symmetric, there is an empty host-less
partition between the two switches which the host must enumerate and
assign BAR addresses to. The firmware in the switch manages this
specially so that the BAR addresses on both sides of the empty
partition will be identical despite being in the same partition with
the same address space.
The driver determines whether crosslink is enabled by a flag set in
the NTB partition info registers which are set by the switch's
configuration file.
When crosslink is enabled, a reserved LUT window is setup to point to
the peer's switch's NTB registers and the local MWs are set to forward
to the host-less partition's BARs. (Yes, this hurts my brain too.)
Once this is setup, largely the same NTB infrastructure is used to
communicate between the two hosts.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a prep patch in order to support the crosslink feature which
will require the driver to setup the requester ID table in another
partition as well as it's own. To aid this, create a helper function
which sets up the requester IDs from an array.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a prep patch in order to support the crosslink feature which
will require the driver to use another reserved LUT window. To
simplify this we move the code which sets up the reserved LUT window
into a helper function which will be used by the crosslink
initialization.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a prep patch in order to support the crosslink feature which will
require the driver to use another reserved LUT window. To simplify this,
we add some code to track the number of reserved LUT windows in use
instead of assuming this is always 1.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.
Use following logic to determine the NT peer partition:
1) If there are 2 partitions, and the target vector is set in
the Switchtec configuration, use the partition specified in target
vector.
2) If there are 2 partitions and target vector is unset
use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
this is invalid and report an error.
Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This resolves a bug which may incorrectly configure the peer host's
LUT for shared memory window access. The code was using the local
host's first BAR number, rather than the peer hosts's first BAR
number, to determine what peer NT control register to program.
The bug will cause the Switchtec NTB link to work only if both peers
have the same first NTB BAR configured. In all other configurations,
the link will not come up, failing silently.
When both hosts have the same first BAR, the configuration works only
because the first BAR numbers happent to be the same. When the hosts
do not have the same first BAR, then the LUT translation will not be
configured in the correct peer LUT and will not give the peer the
shared memory window access required for the link to operate.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Switchtec hardware has two types of memory windows: LUTs and Direct.
The first area in each BAR is for LUT windows and the remaining area is
for the direct region. The total number of LUT entries is set by a
configuration setting in hardware and they all must be the same
size. (This is fixed by switchtec_ntb to be 64K.)
switchtec_ntb enables the LUTs only for the first BAR and enables the
highest power of two possible. Seeing the LUTs are at the beginning of
the BAR, the direct memory window's alignment is affected. Therefore,
the maximum direct memory window size can not be greater than the number
of LUTs times 64K. The direct window in other BARs will not have this
restriction as the LUTs will not be enabled there. LUTs will only be
exposed through the NTB API if the use_lut_mw parameter is set.
Seeing the Switchtec hardware, by default, configures BARs to be 4G a
module parameter is given to limit the size of the advertised memory
windows. Higher layers tend to allocate the maximum BAR size and this
has a tendency to fail when they try to allocate 4GB of contiguous
memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing there is no dedicated hardware for this, we simply add
these as entries in the shared memory window. Thus, we could support
any number of them but 128 seems like enough, for now.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pretty straightforward implementation of doorbell registers.
The shift and mask were setup in an earlier patch and this just hooks
up the appropriate portion of the IDB register as the local doorbells
and the opposite portion of ODB as the peer doorbells. The DB mask is
protected by a spinlock to avoid concurrent read-modify-write accesses.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
switchtec_ntb checks for a link by looking at the shared memory
window. If the magic number is correct and the other side indicates
their link is enabled then we take the link to be up.
Whenever we change our local link status we send a msg to the
other side to check whether it's up and change their status.
The current status is maintained in a flag so ntb_is_link_up
can return quickly.
We utilize Switchtec's link status notifier to also check link changes
when the switch notices a port changes state.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add a skeleton NTB driver which will be filled out in subsequent patches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set up some hardware registers and creates interrupt service routines
for the doorbells and messages.
There are 64 doorbells in the switch that are shared between all
partitions. The upper 4 doorbells are also shared with the messages
and are therefore not used. Thus, this provides 28 doorbells for each
partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add the code to initialize the memory windows in the hardware.
This includes setting up the requester ID table, and figuring out
which BAR corresponds to which memory window. (Seeing the switch
can be configured with any number of BARs.)
Also, seeing the device doesn't have hardware for scratchpads or
determining the link status, we create a shared memory window that has
these features. A magic number with a version component will be used
to determine if the other side's driver is actually up.
The shared memory window also informs the other side of the
size and count of the local memory windows.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>