Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
Some boards that were added after the mass io_pgoffst/io_physio
removal, and were not updated in the original patch. Fixup here.
c.f. original io_pgoffst/io_physio removal
commit 6451d7783b
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most of the regulator data structures are local to the
board file, but not made static. Fix this.
Also make the nand partition table static.
This gets rid of all the sparse warnings for this file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On Davinci SRAM is mapped as MT_DEVICE becasue of the section
mapping pre-requisite instead of intended MT_MEMORY_NONCACHED
Since the section mapping limitation gets fixed with first
patch in this series, the MT_MEMORY_NONCACHED can be used now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds initial support for the Hawkboard-L138 system
It is under the machine name "omapl138_hawkboard".
This system is based on the da850 davinci CPU architecture.
Information on these system may be found at http://www.hawkboard.org.
Basic support for the UART console is included in this patch.
It's tested with latest Angstrom File Systems like ramdisk
from http://alturl.com/imb45.
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For the MityDSP-L138/MityARM-1808 SOMS, read the factory assigned
MAC address from the onboard I2C EPROM and assign it to the emac
device during platform initialization.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's touchscreen
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds evm board specific keymap definitions and controller
configuration data for on-chip keypad controller on tnetv107x silicon.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's keypad
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.
In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds mdio platform devices on SoCs that have the necessary
hardware. Clock lookup entries (aliases) have also been added, so that the
MDIO and EMAC drivers can independently enable/disable a shared underlying
clock. Further, the EMAC MMR region has been split down into separate MDIO
and EMAC regions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the i2c0 bus and attached devices to the MityDSP-L138
and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator
needed for power management and a small 24c02 EPROM that contains
factory configuration data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds an entry into the idcode table for tnetv107x silicon revision
1.1 and 1.2 devices.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system
on Module (SOM) under the machine name "mityomapl138". These SOMs are based
on the da850 davinci CPU architecture. Information on these SOMs may be
found at http://www.mitydsp.com.
Basic support for the console UART, NAND, and EMAC (MII interface) is
included in this patch.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds machine checks in the serial console init routines
for the DA8XX EVM boards. This is needed because there are other
DA8XX based machines that use a different UART/tty as the console
and may be included in a common kernel build.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup NAND flash timing on DM6467T EVM.
Without the timing setup, the NAND flash on DM6467T
RevC EVM reports a number of random bad blocks because
of read errors.
Also, with this, copying a 100M file on RevB EVM takes
~35 sec against 1 minute 30 seconds earlier.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup the NAND flash timings for DA850 EVM
Before configuring the timing values, throughput calculation
using dd command yielded 469 kB/s write and 966 kB/s read speed.
After the timing configuration, the throughput was measured to
be 2.4 MB/s write and 5 MB/s read.
[Mukul Bhatnagar: actual calculation of timing values from the
NAND datasheet]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Mukul Bhatnagar <mbhatnagar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setup the NAND flash timings for DA830 EVM.
Before configuring the timing values, throughput calculation
using dd command yielded 477 kB/s write and 970 kB/s read speed.
After the timing configuration, the throughput was measured to
be 2.5 MB/s write and 5.1 MB/s read.
[Mukul Bhatnagar: actual calculation of timing values from the
NAND datasheet]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mukul Bhatnagar <mbhatnagar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DM644x EVM nand flash timing was earlier being
done as a special case in the NAND driver itself.
With the NAND driver now capable of progamming the
AEMIF interface using timing data passed from the
platform, the timing values are being moved into
their rightful place in the EVM specific board file.
The values being programmed match what was being done
earlier and thus do not represent any change in
performance/functionality.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the audio driver uses EDMAQ_0 as the DMA queue,
but on DM365 this queue is specially designed for video
transfers with a large fifo size. Having both audio and
video transfers on the same queue leads to noise on the
audio side.
This patch changes the audio queue number for DM365 to
EDMAQ_3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add resources, platform device and convenience registration function for DA850's second MMC/SD controller (MMCSD1).
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Split mmcsd_clk into mmcsd0_clk and mmcsd1_clk and add davinci_mmc.1
in preparation for adding support for MMCSD1 peripheral in DA850.
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add LPSC id for DA850's MMCSD1 peripheral.
Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
If irq2ctlr() fails return IRQ_NONE.
Also as it can fail make 'ctlr' signed.
The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)
// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }
@@
identifier r1.f;
type T;
unsigned T x;
@@
*x = f(...)
...
*x > 0
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode
specific pin lists, while what pin group is used is a function of how the board
is wired. Copy the pin lists to board-da850-evm.c, renaming them accordingly,
and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing
the CPGMAC module as a whole...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board
specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c,
renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the
two lists in da850.c into one, representing the EMIF 2.5 module as a whole,
just like we have it in da830.c...
While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as
this function is called from non '__init' code...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is a bugfix for the original tnetv107x submission series. The psc_regs
base array was being discarded post-init, and this was causing a crash during
post-init clock enable/disable.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF
timing to remain valid even as the PLL0 output is changed by cpufreq
driver to save power.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On OMAP-L138 SoC, some of the sysclks need not be at a fixed ratio
to CPU clock and can be kept at a relatively constant rate by
adjusting the PLLDIVn ratio even as cpufreq goes ahead and changes
the CPU clock.
This feature can be used to keep the EMIFA (PLL0 SYSCLK3) clock at a
constant rate so that the EMIF timings need not be re-programmed
whenever the CPU frequency changes.
This patch adds the required suppport to cpufreq driver.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Setting sysclk rate will be useful in cases where the
sysclk is not at a fixed ratio to the PLL output but
can asynchronously be changed.
This support forms the basis of attempt to keep the AEMIF
clock constant on OMAP-L138 even as PLL0 output changes
as ARM clock is changed to save power.
This patch has been tested on OMAP-L138.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch disables internal pulldowns for all MMC/SD1
pins. Presently only MMCSD1_CMD pin's pull down is
disabled, but with this some MMC/SD cards do not get
detected on MMC/SD1 slot of the EVM.
The problem was reproducible with SanDisk 4GB SDHC card.
Reported-by: Stephane Bovagne <s-bovagne@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For each DA850 OPP, the normal ('NOM') voltage defined in the tecnical
reference manual (TRM) is actually the minimum voltage the frequency
is supported at.
The minimum ('MIN') voltage defined in TRM is meant to take care of
voltage fluctuations and the device should not be run at this voltage
for extended periods of time.
Fix the OPP definitions to define the cvdd_min as the normal voltage
defined in the datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin
compatible ARM9 microprocessor offering from TI.
The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin
compatible ARM9 microprocessor offering from TI.
More information about these processors available at:
www.ti.com/am1x
Because of their compatibiliy with OMAP-L1x, the kernel
support for OMAP-L1x is fully relevant to AM1x processors.
This patch updates the Kconfig prompt and help text to include
the AM1x part names to help users select configurations required
for these parts easily.
Also, the hardware information that shows up in /proc/cpuinfo
is updated to show applicability of the respective OMAP-L1x EVMs
for AM1x parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In arch/arm/mach-davinci/Kconfig, some of the configuration
items are indented with multiple spaces instead of tabs.
Also, in couple of places, two spaces are used in the middle
of help text where one should do.
This patch fixes both issues.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current cpufreq code does not consider errors that can occur while
changing voltage. Code to increase CPU frequency goes ahead even in
the case the regulator has failed to increase the voltage. This leads
to hard error since lower voltages cannot support increased frequency.
Prevent this by not increasing frequency in case increasing voltage
is not successful.
Also, do not lower the voltage if changing the cpu frequency has failed
for some reason.
Note that we do not return error on failure to decrease voltage as
that is not a hard error.
Build fix for non-cpufreq kernels by Caglar Akyuz.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Caglar Akyuz <caglar@bilkon-kontrol.com.tr>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The long list of clocks being disabled on boot is noisy and not needed
for standard boots. Make this a debug printk instead.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Without this cleanup, sparse checker reports warnings of the type:
CHECK arch/arm/mach-davinci/board-da850-evm.c
arch/arm/mach-davinci/board-da850-evm.c:112:22: warning: symbol 'da850_evm_nandflash_partition' was not declared. Should it be static?
The nand flash partitions and regulator supplies are used within
the EVM file and so should have been static
This patch has been boot tested on DA830 and DA850 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
davinci: dm646x EVM: Specify reserved EDMA channel/slots
davinci: da8xx/omapl EVM: Specify reserved channels/slots
davinci: support for EDMA resource sharing
davinci: edma: provide ability to detect insufficient CC info data
davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities
davinci: DM365: fixed second serial port
Davinci: tnetv107x evm board initial support
Davinci: tnetv107x initial gpio support
Davinci: tnetv107x soc support
Davinci: tnetv107x decompresser uart definitions
Davinci: generalized debug macros
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
