It seems that Conexant CX20549 chip handle only a single input-amp even
though the audio-input widget has multiple sources. This has been never
clear, and I implemented in the current way based on the debug information
I got at the early time -- the device reacts individual input-amp values
for different sources. This is true for another Conexant codec, but it's
not applied to CX20549 actually.
This patch changes the auto-parser code to handle a single input-amp
per audio-in widget for CX20549. After applying this, you'll see only a
single "Capture" volume control instead of separate "Mic" or "Line"
captures when the device is set up to use a single ADC.
We haven't tested 20551 and 20561 codecs yet. If these show the similar
behavior like 20549, they need to set spec->single_adc_amp=1, too.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC260 has multiple mixer widgets connected to the shared DAC, but the
driver currently doesn't check this possibility and ignores when the DAC
is shared with others. This resulted in the silent output from some
routes because of lack of the amp setup.
This patch adds the workaround for it by checking the route even with the
shared DAC, but also checking the conflict with the existing control for
the very same widget NID.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=726812
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was
introduced via genhd.h by the general purpose partition patch.
To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using
DISK_NAME_LEN.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Andrei Warkentin <andreiw@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Reported-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
In my last patch I did a stupid mistake and broke the exofs
compilation completely. Fix it ASAP.
Instead of obj-y I did obj-$(y)
Really Really sorry. Me totally blushing :-{|
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://github.com/jgarzik/libata-dev: (50 commits)
pata_efar: fix register naming used in efar_set_piomode()
pata_rdc: add Power Management support
ata_piix: unify code for programming PIO and MWDMA timings
ata_piix: SITRE handling fix
libata: make ata_sff_data_xfer_noirq() work with 32-bit PIO
pata_artop: add Power Management support
pata_sl82c105: add Power Management support
pata_pdc2027x: add Power Management support
pata_legacy: use PIO mask defines
pata_legacy: unify QDI ->set_piomode methods
libata: remove no longer needed pata_qdi driver
pata_it8213: fix register naming used in it8213_set_piomode()
pata_it8213: add UDMA100 and UDMA133 support
pata_rdc: parallel scanning needs an extra locking
pata_via: add via_fixup()
libata: ata_timing_compute() fixup
pata_scc: add proper cable detection method
pata_arasan_cf: remove bogus to_platform_device() calls
pata_atiixp: add proper ->prereset method
pata_serverworks: add serverworks_fixup()
...
run_guest tries to freeze the current process after it has handled
pending interrupts and before it calls lguest_arch_run_guest.
This doesn't work nicely if the task has been killed while being frozen
and when we want to handle that signal as soon as possible.
Let's move try_to_freeze before we check for pending signal so that we
can get out of the loop as soon as possible.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Host might be running under KVM, but we shouldn't allow Guest to think it
can use KVM hypercalls (it can't, and it will embarrass itself if it tries).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We actually can run under KVM, as it doesn't paravirtualize anything we
need to use; reduce the check to checking we are the normal ringlevel.
Reported-by: Stefanos Geraggelos <sgerag@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au># HG changeset patch
The current h8300 GPIO implementation doesn't provide the standard GPIO
API, and in fact provides only direction control rather than normal GPIO
functionality. Currently this is only used by the platform interrupt
implementation rather than by a range of drivers so in preparation for
moving over to gpiolib move the header out of the way of the gpiolib
header, allowing a default GPIO implementation to be provided.
For actual use of these GPIOs with gpiolib a real driver would still need
to be written but there appears to be no current need for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Should call the platform-specific __gpio_{get,set}_value
instead of generic gpio_{get,set}_value
Signed-off-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The association numbers of surround/CLFE speaker pins aren't correctly
mapped by the auto-parser. This patch fixes the CLFE speaker pin to the
right assoc value (from 3 to 1).
Tested-by: Nika Topolchanskaya <nanodesuu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.
This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Reported-by: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.
This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA. It assumes 2.40a is the latest version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only allow runtime PM for devices that specifically indicate
that they support it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Go through the driver's set_power() functions rather than
calling regulator_enable/disable() directly because otherwise
pbias configuration for MMC1 is not done.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sc->clk_bus[ptr] could be NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed. During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.
For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
