When host set the host->tuning_delay, even the last tuning
command need a delay, otherwise the first command after the
tuning will meet issue.
Take i.MX7D as an example, there will be the following log:
mmc2: switch to high-speed from hs200 failed, err:-110
mmc2: error -110 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that i.MX uSDHC needed delay between tuning
cycles for HS200 successful tuning. This patch is to set 1ms
delay for that.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX6ULL has errata ERR010450, point out that due to SOC I/O
timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the
clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO
DDR50 mode, the clock rate can't exceed 45MHz.
This patch add this limit for imx6ull.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed comments and whitespace]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a imx6ull compatible string to be able to manage erratum ERR010450 on
i.MX6ULL.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.
Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX
uSDHC internally already uses a fixed optimized timing for
DDR50, normally does not require tuning for DDR50 mode.
This patch specify a new execute_tuning function for i.MX
uSDHC, do not impact i.MX eSDHC.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it
choose to use standard tuning method. So on linux side, if choose to
use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN,
remove the impact of bootloader code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variant specific driver data doesn't change at run-time, so mark it as
const to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci_am654.c:161:18: warning:
symbol 'sdhci_am654_ops' was not declared. Should it be static?
Fixes: aff88ff23512 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcclOnAAoJEL/70l94x66DAjIH/28XLAkaAtJIsm4nTy3sb6nC
UC7suhEEst4zyRCzUlMdeaMkuWJitx5Bun0x9k5uYvMXqmndXcGq3wLmrRhOY2u2
iN1myLESOn0+lubVcK/+ht2rat2AO9XqpOKPojBRs/c6MW1UAIJIPKly/ls1++Ee
TmdIKrgqGgE5Ywx4ObvXBDOeWSKUwxqqNi7FUkWpACJckvmQoKJX0Hre5ICW6lom
+yUBC1rR9apMLTe2QIW2kBZ9JTKCX0aErdmnLXlyZbFOOk0udzNaDy+kXSs7w9Bk
tu8biO7xBNJrcR5e+fEipVFIdN9au0aM5pJWq9s4yeqSnDKB1FRekoJj5yvTqus=
=1GQR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This callback was removed some time ago, also remove the documentation.
Fixes: 1b6dd556c3 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5a2de63fd1 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e26 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e26 ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like commit e2ba732a16 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One fix for an oops when using SRIOV, introduced by the recent changes to
support compound IOMMU groups.
Thanks to:
Alexey Kardashevskiy.
-----BEGIN PGP SIGNATURE-----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=NBtz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
to support compound IOMMU groups.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/sriov: Register IOMMU groups for VFs
Four small fixes: three in drivers and one in the core. The core fix
is also minor in scope since the bug it fixes is only known to affect
systems using SCSI reservations. Of the driver bugs, the libsas one
is the most major because it can lead to multiple disks on the same
expander not being exposed.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHC4uSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfYwAP9zX676
svxUeEQLLyMLXmGyDZ5um8ne8VDAzXDIrkS06gEAhKju7hb7jYvt0pf3jj+utS+v
KXtT8CpMuj+cffeVXng=
=OkZL
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull keys fixes from James Morris:
"Two fixes from Eric Biggers"
* 'fixes-v5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: always initialize keyring_index_key::desc_len
KEYS: user: Align the payload buffer
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory
that has just been freed (Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7rW+
-----END PGP SIGNATURE-----
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nXrB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign [Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg [Vineet]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cNCN
-----END PGP SIGNATURE-----
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m7U7
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before derefencing the encap pointer, commit e7cc082455 ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e0 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: firmware message delay fixes.
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang says:
====================
Code-gen for BPF_ALU | BPF_XOR | BPF_K is wrong when imm is -1,
also high 32-bit of 64-bit register should always be cleared.
This set fixed both bugs.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The intended optimization should be A ^ 0 = A, not A ^ -1 = A.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
-----BEGIN PGP SIGNATURE-----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=JEqH
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev says:
====================
nic: thunderx: fix communication races between VF & PF
The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.
After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.
Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.
This patch series is to address race condition with VF & PF communication.
Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
from int to void;
- 0007: update subject and remove unused variable 'netdev'
from nicvf_link_status_check_task() function;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>