Revert commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups
from suspend-to-idle) as it turned out to be premature and triggered
a number of different issues on various systems.
That includes, but is not limited to, premature suspend-to-RAM aborts
on Dell XPS 13 (9343) reported by Dominik.
The issue the commit in question attempted to address is real and
will need to be taken care of going forward, but evidently more work
is needed for this purpose.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled (that also helps to catch device-induced
wakeup events occurring during suspend transitions in progress).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers that needs acpi_device_fix_up_power(), allow them to be built as
modules by exporting this function.
Cc: <stable@vger.kernel.org> # 4.5+
Tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.
This patch also changes all current code that directly sets the
dev.pm_domain pointer.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a concern that if the platform firmware was involved in
the system resume that's being completed, some devices might have
been reset by it and if those devices had the power.direct_complete
flag set during the preceding suspend transition, they may stay
in a reset-power-on state indefinitely (until they are runtime-resumed
and then suspended again). That may not be a big deal from the
individual device's perspective, but if the system is an SoC, it may
be prevented from entering deep SoC-wide low-power states on idle
because of that.
The devices that are most likely to be affected by this issue are
PCI devices and ACPI-enumerated devices using the general ACPI PM
domain, so to prevent it from happening for those devices, force a
runtime resume for them if they have their power.direct_complete
flags set and the platform firmware was involved in the resume
transition currently in progress.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
ACPI / bus: Move duplicate code to a separate new function
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
ACPI / PM: Update the copyright notice and description of power.c
Commit 20dacb71ad ("ACPI / PM: Rework device power management to follow
ACPI 6") changed the device power management to use D3hot if the device
in question does not have _PR3 method even if D3cold was requested by the
caller.
However, if the device has _PR3 device->power.state is also set to D3hot
instead of D3Cold after power resources have been turned off because
device->power.state will be assigned from "state" instead of
"target_state".
Next time the device is transitioned to D0, acpi_power_transition() will
find that the current power state of the device is D3hot instead of D3cold
which causes it to power down all resources required for the current
(wrong) state D3hot.
Below is a simplified ASL example of a real touch panel device which
triggers the problem:
Scope (TPL1)
{
Name (_PR0, Package (1) { \_SB.PCI0.I2C1.PXTC })
Name (_PR3, Package (1) { \_SB.PCI0.I2C1.PXTC })
...
}
In both D0 and D3hot the same power resource is required. However, when
acpi_power_transition() turns off power resources required for D3hot (as
the device is transitioned to D0) it powers down PXTC which then makes the
device to lose its power.
Fix this by assigning "target_state" to the device power state instead of
"state" that is always D3hot even for devices with valid _PR3.
Fixes: 20dacb71ad (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.
In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.
Fixes: f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI 6 specification has made some changes in the device power
management area. In particular:
* The D3hot power state is now supposed to be always available
(instead of D3cold) and D3cold is only regarded as valid if the
_PR3 object is present for the given device.
* The required ordering of transitions into power states deeper than
D0 is now such that for a transition into state Dx the _PSx method
is supposed to be executed first, if present, and the states of
the power resources the device depends on are supposed to be
changed after that.
* It is now explicitly forbidden to transition devices from
lower-power (deeper) into higher-power (shallower) power states
other than D0.
Those changes have been made so the specification reflects the
Windows' device power management code that the vast majority of
systems using ACPI is validated against.
To avoid artificial differences in ACPI device power management
between Windows and Linux, modify the ACPI device power management
code to follow the new specification. Add comments explaining the
code flow in some unclear places.
This only may affect some real corner cases in which the OS behavior
expected by the firmware is different from the Windows one, but that's
quite unlikely. The transition ordering change affects transitions
to D1 and D2 which are rarely used (if at all) and into D3hot and
D3cold for devices actually having _PR3, but those are likely to
be validated against Windows anyway. The other changes may affect
code calling acpi_device_get_power() or acpi_device_update_power()
where ACPI_STATE_D3_HOT may be returned instead of ACPI_STATE_D3_COLD
(that's why the ACPI fan driver needs to be updated too) and since
transitions into ACPI_STATE_D3_HOT may remove power now, it is better
to avoid this one in acpi_pm_device_sleep_state() if the "no power
off" PM QoS flag is set.
The only existing user of acpi_device_can_poweroff() really cares
about the case when _PR3 is present, so the change in that function
should not cause any problems to happen too.
A plus is that PCI_D3hot can be mapped to ACPI_STATE_D3_HOT
now and the compatibility with older systems should be covered
automatically.
In any case, if any real problems result from this, it still will
be better to follow the Windows' behavior (which now is reflected
by the specification too) in general and handle the cases when it
doesn't work via quirks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 5de21bb998 ("ACPI / PM: Drop CONFIG_PM_RUNTIME from the
ACPI core"), all occurrences of CONFIG_PM_RUNTIME were replaced with
CONFIG_PM. This created the following structure of #ifdef blocks in
the code:
[...]
#ifdef CONFIG_PM
#ifdef CONFIG_PM
/* always on / undead */
#ifdef CONFIG_PM_SLEEP
[...]
#endif
#endif
[...]
#endif
This patch removes the inner "#ifdef CONFIG_PM" block as it will
always be enabled when the outer block is enabled. This inconsistency
was found using the undertaker-checkpatch tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an ACPI device object whose _STA returns 0 (not present and not
functional) has _PR0 or _PS0, its power_manageable flag will be set
and acpi_bus_init_power() will return 0 for it. Consequently, if
such a device object is passed to the ACPI device PM functions, they
will attempt to carry out the requested operation on the device,
although they should not do that for devices that are not present.
To fix that problem make acpi_bus_init_power() return an error code
for devices that are not present which will cause power_manageable to
be cleared for them as appropriate in acpi_bus_get_power_flags().
However, the lists of power resources should not be freed for the
device in that case, so modify acpi_bus_get_power_flags() to keep
those lists even if acpi_bus_init_power() returns an error.
Accordingly, when deciding whether or not the lists of power
resources need to be freed, acpi_free_power_resources_lists()
should check the power.flags.power_resources flag instead of
flags.power_manageable, so make that change too.
Furthermore, if acpi_bus_attach() sees that flags.initialized is
unset for the given device, it should reset the power management
settings of the device and re-initialize them from scratch instead
of relying on the previous settings (the device may have appeared
after being not present previously, for example), so make it use
the 'valid' flag of the D0 power state as the initial value of
flags.power_manageable for it and call acpi_bus_init_power() to
discover its current power state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
* acpi-scan:
ACPI / scan: Change the level of _DEP-related messages to KERN_DEBUG
* acpi-utils:
ACPI / utils: Drop error messages from acpi_evaluate_reference()
* acpi-pm:
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
In some cases acpi_device_wakeup() may be called to ensure wakeup
power to be off for a given device even though that device's wakeup
GPE has not been enabled so far. It calls acpi_disable_gpe() on a
GPE that's not enabled and this causes ACPICA to return the AE_LIMIT
status code from that call which then is reported as an error by the
ACPICA's debug facilities (if enabled). This may lead to a fair
amount of confusion, so introduce a new ACPI device wakeup flag
to store the wakeup GPE status and avoid disabling wakeup GPEs
that have not been enabled.
Reported-and-tested-by: Venkat Raghavulu <venkat.raghavulu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As reported by Dmitry, on some Chromebooks there are devices with
corresponding ACPI objects and with unusual system wakeup
configuration. Namely, they technically are wakeup-capable, but the
wakeup is handled via a platform-specific out-of-band mechanism and
the ACPI PM layer has no information on the wakeup capability. As
a result, device_may_wakeup(dev) called from acpi_dev_suspend_late()
returns 'true' for those devices, but the wakeup.flags.valid flag is
unset for the corresponding ACPI device objects, so acpi_device_wakeup()
reproducibly fails for them causing acpi_dev_suspend_late() to return
an error code. The entire system suspend is then aborted and the
machines in question cannot suspend at all.
Address the problem by ignoring the device_may_wakeup(dev) return
value in acpi_dev_suspend_late() if the ACPI companion of the device
being handled has wakeup.flags.valid unset (in which case it is clear
that the wakeup is supposed to be handled by other means).
This fixes a regression introduced by commit a76e9bd89a (i2c:
attach/detach I2C client device to the ACPI power domain) as the
affected systems could suspend and resume successfully before that
commit.
Fixes: a76e9bd89a (i2c: attach/detach I2C client device to the ACPI power domain)
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix for a recent PCI power management change that overlooked
the fact that some IRQ chips might not be able to configure
PCIe PME for system wakeup from Lucas Stach.
- Fix for a bug introduced in 3.17 where acpi_device_wakeup()
is called with a wrong ordering of arguments from Zhang Rui.
- A bunch of intel_pstate driver fixes (all -stable candidates)
from Dirk Brandewie, Gabriele Mazzotta and Pali Rohár.
- Fixes for a rather long-standing problem with the OOM killer
and the freezer that frozen processes killed by the OOM do
not actually release any memory until they are thawed, so
OOM-killing them is rather pointless, with a couple of
cleanups on top (Michal Hocko, Cong Wang, Rafael J Wysocki).
- ACPICA update to upstream release 20140926, inlcuding mostly
cleanups reducing differences between the upstream ACPICA and
the kernel code, tools changes (acpidump, acpiexec) and
support for the _DDN object (Bob Moore, Lv Zheng).
- New PM QoS class for memory bandwidth from Tomeu Vizoso.
- Default 32-bit DMA mask for platform devices enumerated by ACPI
(this change is mostly needed for some drivers development in
progress targeted at 3.19) from Heikki Krogerus.
- ACPI EC driver cleanups, mostly related to debugging, from
Lv Zheng.
- cpufreq-dt driver updates from Thomas Petazzoni.
- powernv cpuidle driver update from Preeti U Murthy.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=4Q8f
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This is material that didn't make it to my 3.18-rc1 pull request for
various reasons, mostly related to timing and travel (LinuxCon EU /
LPC) plus a couple of fixes for recent bugs.
The only really new thing here is the PM QoS class for memory
bandwidth, but it is simple enough and users of it will be added in
the next cycle. One major change in behavior is that platform devices
enumerated by ACPI will use 32-bit DMA mask by default. Also included
is an ACPICA update to a new upstream release, but that's mostly
cleanups, changes in tools and similar. The rest is fixes and
cleanups mostly.
Specifics:
- Fix for a recent PCI power management change that overlooked the
fact that some IRQ chips might not be able to configure PCIe PME
for system wakeup from Lucas Stach.
- Fix for a bug introduced in 3.17 where acpi_device_wakeup() is
called with a wrong ordering of arguments from Zhang Rui.
- A bunch of intel_pstate driver fixes (all -stable candidates) from
Dirk Brandewie, Gabriele Mazzotta and Pali Rohár.
- Fixes for a rather long-standing problem with the OOM killer and
the freezer that frozen processes killed by the OOM do not actually
release any memory until they are thawed, so OOM-killing them is
rather pointless, with a couple of cleanups on top (Michal Hocko,
Cong Wang, Rafael J Wysocki).
- ACPICA update to upstream release 20140926, inlcuding mostly
cleanups reducing differences between the upstream ACPICA and the
kernel code, tools changes (acpidump, acpiexec) and support for the
_DDN object (Bob Moore, Lv Zheng).
- New PM QoS class for memory bandwidth from Tomeu Vizoso.
- Default 32-bit DMA mask for platform devices enumerated by ACPI
(this change is mostly needed for some drivers development in
progress targeted at 3.19) from Heikki Krogerus.
- ACPI EC driver cleanups, mostly related to debugging, from Lv
Zheng.
- cpufreq-dt driver updates from Thomas Petazzoni.
- powernv cpuidle driver update from Preeti U Murthy"
* tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
intel_pstate: Correct BYT VID values.
intel_pstate: Fix BYT frequency reporting
intel_pstate: Don't lose sysfs settings during cpu offline
cpufreq: intel_pstate: Reflect current no_turbo state correctly
cpufreq: expose scaling_cur_freq sysfs file for set_policy() drivers
cpufreq: intel_pstate: Fix setting max_perf_pct in performance policy
PCI / PM: handle failure to enable wakeup on PCIe PME
ACPI: invoke acpi_device_wakeup() with correct parameters
PM / freezer: Clean up code after recent fixes
PM: convert do_each_thread to for_each_process_thread
OOM, PM: OOM killed task shouldn't escape PM suspend
freezer: remove obsolete comments in __thaw_task()
freezer: Do not freeze tasks killed by OOM killer
ACPI / platform: provide default DMA mask
cpuidle: powernv: Populate cpuidle state details by querying the device-tree
cpufreq: cpufreq-dt: adjust message related to regulators
cpufreq: cpufreq-dt: extend with platform_data
cpufreq: allow driver-specific data
ACPI / EC: Cleanup coding style.
ACPI / EC: Refine event/query debugging messages.
...
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
When we have the acpi_device pointer, there is no need to pass the
device's handle to the acpi_bus_xxx_power functions to get/set/update
the device's power state, instead, use the acpi_device_xxx_power
functions directly.
To make this happen for fan module, export acpi_device_update_power.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The ->detach() callback for the PM domain has now been fully adopted,
thus there no users left of the acpi_dev_pm_detach() API. This allow us
to convert it into a static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As as preparation to simplify the detachment of devices from their PM
domains, we assign the ->detach() callback to genpd_dev_pm_detach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI_HANDLE() macro evaluates ACPI_COMPANION() internally to
return the handle of the device's ACPI companion, so it is much
more straightforward and efficient to use ACPI_COMPANION()
directly to obtain the device's ACPI companion object instead of
using ACPI_HANDLE() and acpi_bus_get_device() on the returned
handle for the same thing.
Do that in three places in the ACPI device PM code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Wakeup GPEs are currently only enabled when setting up devices for
remote wakeup at run time. During system-wide transitions they are
enabled by ACPICA at the very last stage of suspend (before asking
the BIOS to take over). Of course, that only works for system
sleep states supported by ACPI, so in particular it doesn't work
for the "freeze" sleep state.
For this reason, modify the ACPI core device PM code to enable wakeup
GPEs for devices when setting them up for wakeup regardless of whether
that is remote wakeup at runtime or system wakeup. That allows the
same device wakeup setup routine to be used for both runtime PM and
system-wide PM and makes it possible to reduce code size quite a bit.
This make ACPI-based PCI Wake-on-LAN work with the "freeze" sleep
state on my venerable Toshiba Portege R500 and should help other
systems too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since ACPI wakeup GPEs are going to be enabled during system suspend
as well as for runtime wakeup by a subsequent patch and the same
notify handlers will be used in both cases, rework the ACPI device
wakeup notification framework so that the part specific to physical
devices is always run asynchronously from the PM workqueue. This
prevents runtime resume callbacks for those devices from being
run during system suspend and resume which may not be appropriate,
among other things.
Also make ACPI device wakeup notification handling a bit more robust
agaist subsequent removal of ACPI device objects, whould that ever
happen, and create a wakeup source object for each ACPI device
configured for wakeup so that wakeup notifications for those
devices can wake up the system from the "freeze" sleep state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No reason for excluding the remaining ones.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rjw: Rebased and exported the new acpi_subsys_complete() too.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rework the ACPI PM domain's PM callbacks to avoid resuming devices
during system suspend (in order to modify their wakeup settings etc.)
if that isn't necessary.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Runtime-suspended devices are resumed during system suspend by
acpi_subsys_prepare() for two reasons: First, because they may need
to be reprogrammed in order to change their wakeup settings and,
second, because they may need to be operatonal for their children
to be successfully suspended. That is a problem, though, if there
are many runtime-suspended devices that need to be resumed this
way during system suspend, because the .prepare() PM callbacks of
devices are executed sequentially and the times taken by them
accumulate, which may increase the total system suspend time quite
a bit.
For this reason, move the resume of runtime-suspended devices up
to the next phase of device suspend (during system suspend), except
for the ones that have power.ignore_children set. The exception is
made, because the devices with power.ignore_children set may still
be necessary for their children to be successfully suspended (during
system suspend) and they won't be resumed automatically as a result
of the runtime resume of their children.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-processor:
ACPI / scan: reduce log level of "ACPI: \_PR_.CPU4: failed to get CPU APIC ID"
ACPI / processor: Return specific error value when mapping lapic id
* acpi-hotplug:
ACPI / scan: Clear match_driver flag in acpi_bus_trim()
* acpi-init:
ACPI / init: Flag use of ACPI and ACPI idioms for power supplies to regulator API
* acpi-pm:
ACPI / PM: Use ACPI_COMPANION() to get ACPI companions of devices
* acpica:
ACPICA: Remove bool usage from ACPICA.
The ACPI device PM code in device_pm.c uses a special function,
acpi_dev_pm_get_node(), to obtain an ACPI companion object of a given
device. However, that is not necessary any more after recent changes
that introduced the ACPI_COMPANION() macro serving exactly the same
purpose, but working in a much more straightforward way. For this
reason, drop acpi_dev_pm_get_node() and use ACPI_COMPANION() instead
of it everywhere.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Modify the ACPI namespace scanning code to register a struct
acpi_device object for every namespace node representing a device,
processor and so on, even if the device represented by that namespace
node is reported to be not present and not functional by _STA.
There are multiple reasons to do that. First of all, it avoids
quite a lot of overhead when struct acpi_device objects are
deleted every time acpi_bus_trim() is run and then added again
by a subsequent acpi_bus_scan() for the same scope, although the
namespace objects they correspond to stay in memory all the time
(which always is the case on a vast majority of systems).
Second, it will allow user space to see that there are namespace
nodes representing devices that are not present at the moment and may
be added to the system. It will also allow user space to evaluate
_SUN for those nodes to check what physical slots the "missing"
devices may be put into and it will make sense to add a sysfs
attribute for _STA evaluation after this change (that will be
useful for thermal management on some systems).
Next, it will help to consolidate the ACPI hotplug handling among
subsystems by making it possible to store hotplug-related information
in struct acpi_device objects in a standard common way.
Finally, it will help to avoid a race condition related to the
deletion of ACPI namespace nodes. Namely, namespace nodes may be
deleted as a result of a table unload triggered by _EJ0 or _DCK.
If a hotplug notification for one of those nodes is triggered
right before the deletion and it executes a hotplug callback
via acpi_hotplug_execute(), the ACPI handle passed to that
callback may be stale when the callback actually runs. One way
to work around that is to always pass struct acpi_device pointers
to hotplug callbacks after doing a get_device() on the objects in
question which eliminates the use-after-free possibility (the ACPI
handles in those objects are invalidated by acpi_scan_drop_device(),
so they will trigger ACPICA errors on attempts to use them).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
* acpi-pm:
spi: attach/detach SPI device to the ACPI power domain
i2c: attach/detach I2C client device to the ACPI power domain
ACPI / PM: allow child devices to ignore parent power state
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some serial buses like I2C and SPI don't require that the parent device is
in D0 before any of its children transitions to D0, but instead the parent
device can control its own power independently from the children.
This does not follow the ACPI specification as it requires the parent to be
powered on before its children. However, Windows seems to ignore this
requirement so I think we can do the same in Linux.
Implement this by adding a new power flag 'ignore_parent' to struct
acpi_device. If this flag is set the ACPI core ignores checking of the
parent device power state when the device is powered on/off.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The state information can be useful to know what the problem is when
an error message about a device can not being set to a higher power
state than its parent appeared, so this patch adds such state
information for both the target state of the device and the current
state of its parent.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that acpi_device_set_power() checks whether or not the given
device is power manageable, it is not necessary to do this check in
acpi_bus_set_power() any more, so remove it.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify acpi_device_set_power() so that diagnostic messages printed by
it to the kernel log always contain the name of the device concerned
to make it possible to identify the device that triggered the message
if need be.
Also replace printk(KERN_WARNING ) with dev_warn() everywhere in that
function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Make acpi_device_set_power() check if the given device is power
manageable before checking if the given power state is valid for that
device. Otherwise it will print that "Device does not support" that
power state into the kernel log, which may not make sense for some
power states (D0 and D3cold are supported by all devices by
definition).
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The role of acpi_bus_update_power() is to update the given ACPI
device object's power.state field to reflect the current physical
state of the device (as inferred from the configuration of power
resources and _PSC, if available). For this purpose it calls
acpi_device_set_power() that should update the power resources'
reference counters and set power.state as appropriate. However,
that doesn't work if the "new" state is D1, D2 or D3hot and the
the current value of power.state means D3cold, because in that
case acpi_device_set_power() will refuse to transition the device
from D3cold to non-D0.
To address this problem, make acpi_bus_update_power() call
acpi_power_transition() directly to update the power resources'
reference counters and only use acpi_device_set_power() to put
the device into D0 if the current physical state of it cannot
be determined.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
* acpi-pm:
ACPI / PM: Rework and clean up acpi_dev_pm_get_state()
ACPI / PM: Replace ACPI_STATE_D3 with ACPI_STATE_D3_COLD in device_pm.c
ACPI / PM: Rename function acpi_device_power_state() and make it static
ACPI / PM: acpi_processor_suspend() can be static
xen / ACPI / sleep: Register an acpi_suspend_lowlevel callback.
x86 / ACPI / sleep: Provide registration for acpi_suspend_lowlevel.
Rafael J. Wysocki