When omapfb module is removed, the driver will turn off all the displays
it manages. However, it leaves the overlays enabled. While the overlays
are obviously disabled as the displays are disabled, it causes issues
when the driver module is loaded again, as at that point the overlays
are still enabled on the hardware level. The result is that even if the
SW thinks overlays are disabled, they are actually enabled.
Fix this by making sure the overlays are disabled at module removal.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Nowadays it's normal to get -EPROBE_DEFER from, e.g., regulator_get. As
-EPROBE_DEFER is not really an error, and the driver will be probed fine
a bit later, printing an error message will just confuse the user.
This patch changes omapdss to print an error for regulator_gets only if
the error code is something else than -EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is quite common to have omapfb probe deferred because of a missing
resource, and to get omapfb probed succesfully a bit later. This works
fine. However, omapfb does not give any print on a successful probe, so
if the omapfb is actually never probed again after deferral, this is not
shown in the log.
To help debugging, add a simple print from omapfb at the end of its
probe, saying which display it is using and in which resolution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver tries to get the needed memory resources by name and by
ID. Resources by name are not currently defined, and will be used with
DT boot.
The resource names used in the driver are not quite perfect, and as they
are not used yet, we can change them. This patch removes the unneeded
"hdmi_" prefix from the names, and simplifies the names (e.g. hdmi_txphy
-> phy).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI contains three separate blocks: protocol engine, PHY and PLL. At the
moment, all these are memory mapped in one big chunk. We need to split
that memory map into smaller pieces so that we can add proper 'reg'
properties into the DT data for each block.
This patch changes the driver to map the blocks separately. It first
tries to get the memory resource using name, used when booting with DT,
and if that fails, it gets the memory resource by ID, in which case the
driver gets the big chunk from platform data. That big chunk is then
split into the smaller blocks manually.
After DSS DT code has been merged and the old platform code removed, we
can clean up the memory resource management.
Instead of changing the driver in all the places where a register is
read or written, this patch takes a shortcut: it adds an additional
number to the struct which represents the register index. This number is
used to decide which base address to use. In the future we should
consider other approaches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_wait_for_bit_change() has two issues:
The register index was passed as u16, even if the register index may be
u32. Fix the index to u32.
The function was copied from wait_for_bit_change() which waits for a
single bit to change, but the hdmi version was changed to wait for a bit
field. This change was not done correctly.
The function is supposed to return the (last) value of the bit field,
but it returned !val in case of timeout. This was correct for the single
bit version, but not for the hdmi version. Fix the function to return
the actual value in the register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.
Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some reason the hdmi driver first turns off the video output when
it's about to enable the video output. This serves no purpose, and can
be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.
Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21ae
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
There is no reasons why an HVM guest shouldn't be allowed to use xenfb.
As a matter of fact ARM guests, HVM from Linux POV, can use xenfb.
Given that no Xen toolstacks configure a xenfb backend for x86 HVM
guests, they are not affected.
Please note that at this time QEMU needs few outstanding fixes to
provide xenfb on ARM:
http://marc.info/?l=qemu-devel&m=138739419700837&w=2
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
CC: boris.ostrovsky@oracle.com
CC: plagnioj@jcrosoft.com
CC: tomi.valkeinen@ti.com
CC: linux-fbdev@vger.kernel.org
CC: konrad.wilk@oracle.com
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
CC: stable@vger.kernel.org
DSI has separate TX and RX fifos. However, the current code only has one
field where the fifo size is stored, and the code for both TX and RX
config write to the same field. This has not caused issues, as we've
been using the same fifo sizes.
Fix this bug by creating separate fields for TX and RX fifo sizes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss in compat mode creates some sysfs files into the device's sysfs
directory, including a 'name' file. This works fine for
platform_devices, but breaks with i2c or spi devices, as those already
have a 'name' file.
Fix this by renaming the omapdss's 'name' file to 'display_name'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 has MFLAG feature in DISPC. Add the register definition and dump
it. The register is not used yet, though.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb does ovl->get_overlay_info, ovl->set_overlay_info, the set
function may fail even if the info has not been changed. This is because
omapdss doesn't initialize the info, but expect the caller to set valid
values.
Normally that is the case, but there is at least one corner case: if
omapfb has not allocated memory for the overlay yet, and the user uses
ioctl to disable the overlay to make sure it's disabled. In this case
get_overlay_info returns invalid data, but the user is only interested
in setting the overlay to disabled, not configuring it, and
set_overlay_info fails.
The issue is made possible by the omapfb's setup_plane ioctl, which
groups overlay configuration and overlay enable/disable bit into the
same struct. Thus, when you are disabling an overlay, you are also
configuring it.
This is a bit counter intuitive, so I think it's better to initialize
the info to some valid values.
The fields requiring initialization are color_mode and rotation_type,
and also we need to remove the check for (paddr == 0), as paddr is 0 for
unallocated overlay (but it's still fine to disable the overlay).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix debug prints all over omapdss:
* add missing linefeeds
* change pr_err/pr_debug to DSSERR/DSSDBG
* add missing DSS_SUBSYS_NAMEs
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds need to be exported. Add the
EXPORT_SYMBOLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we fail to remove a conflicting fb driver, we need to abort the
loading of the second driver to avoid likely kernel panics.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
No need to have a specific OOM message, since there is generic MM out of memory
message in place.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a handful of powerpc fixes for 3.13.
The patches are reasonably trivial and self contained. Note the offb
patches outside of arch/powerpc, they are LE fixes for our
open-firmware 'dumb' framebuffer"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix up the kdump base cap to 128M
powernv: Fix VFIO support with PHB3
powerpc/52xx: Re-enable bestcomm driver in defconfigs
powerpc/pasemi: Turn on devtmpfs in defconfig
offb: Add palette hack for little endian
offb: Little endian fixes
powerpc: Fix PTE page address mismatch in pgtable ctor/dtor
powerpc/44x: Fix ocm_block allocation
powerpc: Fix build break with PPC_EARLY_DEBUG_BOOTX=y
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node
We shouldn't kfree(fbi) because that was allocated with devm_kzalloc().
There were several error paths which returned directly instead of
releasing resources.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add missing module device table which is needed for module autoloading.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If both CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME are not set:
drivers/video/sh_mobile_meram.c:573: warning: ‘sh_mobile_meram_suspend’ defined but not used
drivers/video/sh_mobile_meram.c:597: warning: ‘sh_mobile_meram_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
kyro would copy u32s and specify sizeof(unsigned long) as the size to copy.
This would copy more data than intended and cause memory corruption and might
leak kernel memory.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When booting Nokia N900 smartphone with v3.12 + omap2plus_defconfig
(LOCKDEP enabled) and CONFIG_DISPLAY_PANEL_SONY_ACX565AKM enabled,
the following BUG is seen during the boot:
[ 7.302154] =====================================
[ 7.307128] [ BUG: bad unlock balance detected! ]
[ 7.312103] 3.12.0-los.git-2093492-00120-g5e01dc7 #3 Not tainted
[ 7.318450] -------------------------------------
[ 7.323425] kworker/u2:1/12 is trying to release lock (&ddata->mutex) at:
[ 7.330657] [<c031b760>] acx565akm_enable+0x12c/0x18c
[ 7.335998] but there are no more locks to release!
Fix by removing double unlock and handling the locking completely inside
acx565akm_panel_power_on() when doing the power on.
Reported-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ZTWO_VADDR() converts from physical to virtual I/O addresses, so it should
return "void __iomem *" instead of "unsigned long".
This allows to drop several casts, but requires adding a few casts to
accomodate legacy driver frameworks that store "unsigned long" I/O
addresses.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch adds support for SoCs that have a dedicated DSS PLL used for
DSS function clock.
If there is no dss parent clock defined, it is presumed that the
functionl clock rate can be set (almost) freely. The code calculates the
highest allowed fck rate, which when divided with some integer gives the
required pck.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need the required pixel clock rate when calculating the dss fclk on
SoCs that have a dedicated DSS PLL.
This patch changes the code to pass the pck to the calc functions. The
pck rate is taken into use in the next patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dss parent_clk_name currently points to a clock node which we use to
change the fclk rate. Now that we have CLK_SET_RATE_PARENT properly set,
we can set the rate directly to the fclk node.
However, we still need to calculate the possible clock rates. For this,
we need the rate of the parent of the current parent_clk.
To simplify the code, this patch changes the parent_clk_name to point to
the above mentioned parent, so that we can get the rate directly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename the variables related to DSS fclk's parent: "clk_name" and
"dpll4_m4_ck", to "parent_clk_name" and "parent_clk", which much better
tell what they mean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove struct dss_clock_info, as it is not usable in a case where DSS
fclk comes from a dedicated PLL. Instead, just use the fclk rate in
place of dss_clock_info, as that is all that's needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver considers OMAP2 DSS's functional clock as a fixed clock.
However, it can be changed, but the possible dividers are not continuous
which is why it was just handled as a fixed clock.
As a partial fix, this patch changes the code to handle the continous
part of the dividers, from 1 to 6. This let's us handle the OMAP2 fck
the same way as fcks on other OMAPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
with few other fixes that popped up during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJShlFZAAoJEBvUPslcq6VzqhsP/Rrk0QYGfOysjNa+6rvCBcqL
+eupoQvhgRC8W3XkXlRPcfatoOWNy9aPxJXgHcuMMQNdOdtKlhXUyOFPseNOuZrb
rJcvQNrbMrOv4yP4ZgknKvk8kbDLdJfcdd1LChOsIZW2X0wdrAljzlEehl0YB5ZU
HdxxmLaNleqJfUwtrXVMPdQiS+FggrvYzDmXeEqpASXH7fnBLHOs8hrK3lMY4g2T
t9JFAzqeHWONUcZoIy0LvgxhmG6P/5nIgyvq9vD17Hd+xkQeJM0GdLRDgOdWxuIC
3yADWwWoVdeJ+bge+lVItNSnewb5tlSaybwu5Oqxze2o7DXysLPC2IdCUT9NwADz
j4Wbqv6GdLdhylI7STZRIfznAQ/k16DLZj8xLVF1UOtDN8aq/UcPqNPVUr83Vhgs
n7bDQFillCY1FWpQPA/AWDUg++dMT0nz7w6a3dfxPjzeaJuDL1hN2yMXbaoMBMcI
i+DAnmxxEwLDGtCNLO5o0iw8xkL7GhE1jwaQp7YQpXcax4ImN4WZy8g2vT3J1iHQ
027vzFE+pUp08AoB+Ug5dPr+UDPqE6EJIc9G5F0x7euL7SC0DuEAld/CPzr/nUgN
g3lfQq/1vmtUVnmGUKoJHv0ysROLGOgdUx897oSdgLw+3F79KiB5g7SnJCOFEnGC
kLwouf9DjMhPwudW75X+
=4fww
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few clock fixes, a runtime PM fix, and pinctrl-single fix along
with few other fixes that popped up during the merge window.
* tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
+ sync with newer trunk
Pull drm updates from Dave Airlie:
"This is a combo of -next and some -fixes that came in in the
intervening time.
Highlights:
New drivers:
ARM Armada driver for Marvell Armada 510 SOCs
Intel:
Broadwell initial support under a default off switch,
Stereo/3D HDMI mode support
Valleyview improvements
Displayport improvements
Haswell fixes
initial mipi dsi panel support
CRC support for debugging
build with CONFIG_FB=n
Radeon:
enable DPM on a number of GPUs by default
secondary GPU powerdown support
enable HDMI audio by default
Hawaii support
Nouveau:
dynamic pm code infrastructure reworked, does nothing major yet
GK208 modesetting support
MSI fixes, on by default again
PMPEG improvements
pageflipping fixes
GMA500:
minnowboard SDVO support
VMware:
misc fixes
MSM:
prime, plane and rendernodes support
Tegra:
rearchitected to put the drm driver into the drm subsystem.
HDMI and gr2d support for tegra 114 SoC
QXL:
oops fix, and multi-head fixes
DRM core:
sysfs lifetime fixes
client capability ioctl
further cleanups to device midlayer
more vblank timestamp fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (789 commits)
drm/nouveau: do not map evicted vram buffers in nouveau_bo_vma_add
drm/nvc0-/gr: shift wrapping bug in nvc0_grctx_generate_r406800
drm/nouveau/pwr: fix missing mutex unlock in a failure path
drm/nv40/therm: fix slowing down fan when pstate undefined
drm/nv11-: synchronise flips to vblank, unless async flip requested
drm/nvc0-: remove nasty fifo swmthd hack for flip completion method
drm/nv10-: we no longer need to create nvsw object on user channels
drm/nouveau: always queue flips relative to kernel channel activity
drm/nouveau: there is no need to reserve/fence the new fb when flipping
drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fence
drm/nouveau: allow nouveau_fence_ref() to be a noop
drm/nvc8/mc: msi rearm is via the nvc0 method
drm/ttm: Fix vma page_prot bit manipulation
drm/vmwgfx: Fix a couple of compile / sparse warnings and errors
drm/vmwgfx: Resource evict fixes
drm/edid: compare actual vrefresh for all modes for quirks
drm: shmob_drm: Convert to clk_prepare/unprepare
drm/nouveau: fix 32-bit build
drm/i915/opregion: fix build error on CONFIG_ACPI=n
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
...
commit 7e0be9f9f7 ('video: exynos_mipi_dsim:
Use the generic PHY driver') resulted in a warning about an unused
variable:
drivers/video/exynos/exynos_mipi_dsi.c:144:26: warning: unused variable
'pdev' [-Wunused-variable]
It is indeed unused; remove it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing particularly stands out in this pull request. The biggest part of the
changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix potential
dead lock" which hopefully fixes the fb locking issues reported by multiple
persons.
There are also a few commits that have changes to arch/arm/mach-at91 and
arch/avr32, which have been acked by the maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=59+j
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Nothing particularly stands out in this pull request. The biggest
part of the changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix
potential dead lock" which hopefully fixes the fb locking issues
reported by multiple persons.
There are also a few commits that have changes to arch/arm/mach-at91
and arch/avr32, which have been acked by the maintainers"
* tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (143 commits)
fb: reorder the lock sequence to fix potential dead lock
fbdev: shmobile-lcdcfb: Convert to clk_prepare/unprepare
fbdev: shmobile-hdmi: Convert to clk_prepare/unprepare
omapdss: Add new panel driver for Topolly td028ttec1 LCD.
video: exynos_mipi_dsi: Unlock the mutex before returning
video: da8xx-fb: remove unwanted define
video: Remove unnecessary semicolons
simplefb: use write-combined remapping
simplefb: fix unmapping fb during destruction
OMAPDSS: connector-dvi: fix releasing i2c_adapter
OMAPDSS: DSI: fix perf measuring ifdefs
framebuffer: Use fb_<level>
framebuffer: Add fb_<level> convenience logging macros
efifb: prevent null-deref when iterating dmi_list
fbdev: fix error return code in metronomefb_probe()
video: xilinxfb: Fix for "Use standard variable name convention"
OMAPDSS: Fix de_level in videomode_to_omap_video_timings()
video: xilinxfb: Simplify error path
video: xilinxfb: Use devm_kzalloc instead of kzalloc
video: xilinxfb: Use standard variable name convention
...
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
'hx8357_dt_ids' is always compiled in. Hence of_match_ptr is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_gpio_request_one rather than requesting and setting direction
in two calls.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add helper function to control the gpio_on signal.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use gpio_is_valid rather than open coding the more restrictive != -1
test.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused include of clk.h.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up get_intensity to increase readability.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up probe error handling by checking parameters before any
allocations and removing an obsolete error label. Also remove unnecessary
reset of private gpio number.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing module alias which is needed for module autoloading.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure to honour gpio polarity also at remove so that the backlight is
actually disabled on boards with active-low enable pin.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver supports 16-bit brightness values, but the value returned
from get_brightness was truncated to eight bits.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the missing destroy_workqueue() before return from
lm3630a_intr_config() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() and devm_lcd_device_register() to
make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() and devm_lcd_device_register() to
make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() and devm_lcd_device_register() to
make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() and devm_lcd_device_register() to
make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() and devm_lcd_device_register() to
make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler, and remove
unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler, and remove
unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler, and remove
unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler. Also,
unnecessary lp855x_backlight_unregister() is removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler, and
remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to
make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following sparse warning:
drivers/video/backlight/lp8788_bl.c:55:25: warning: symbol 'default_bl_config' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't mix different enum types to fix the sparse warnings.
drivers/video/backlight/lm3639_bl.c:80:51: warning: mixing different enum types
drivers/video/backlight/lm3639_bl.c:80:51: int enum lm3639_fleds versus
drivers/video/backlight/lm3639_bl.c:80:51: int enum lm3639_bleds
drivers/video/backlight/lm3639_bl.c:82:51: warning: mixing different enum types
drivers/video/backlight/lm3639_bl.c:82:51: int enum lm3639_fleds versus
drivers/video/backlight/lm3639_bl.c:82:51: int enum lm3639_bleds
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following sparse warnings:
drivers/video/backlight/ld9040_gamma.h:172:3: warning: symbol 'gamma_table' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
