This patch introduces a new timer, which will release
queued-up MPDUs from the reorder buffer, whenever
they've waited for more than HT_RX_REORDER_BUF_TIMEOUT
(which is at around 100 ms).
The advantage of having a dedicated timer, instead of
relying on a constant stream of freshly arriving aMPDUs
to release the old ones, is particularly observable when
even a small fraction of MPDUs are forever lost at
low network speeds.
Previously under these circumstances frames would become
stuck in the reorder buffer and the network stack of both
HT peers throttled back, instead of revving up and
gunning the pipes.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a few stale parameters and variables
which survived the last, large rx-path reorganization:
"mac80211: correctly place aMPDU RX reorder code"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes the reorder logic from the RX path and
moves it into separate routines to make the expired frame
release accessible.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_add_key() currently returns -ENOMEM in case of any error,
including a missing crypto algorithm. Change ieee80211_key_alloc()
and ieee80211_aes_{key_setup_encrypt,cmac_key_setup}() to encode
errors with ERR_PTR() rather than returning NULL, and change
ieee80211_add_key() accordingly.
Compile-tested only.
Reported-by: Marcin Owsiany <porridge@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having both scan and work mutexes is not just
a bit too fine grained, it also creates issues
when there's code that needs both since they
then need to be acquired in the right order,
which can be hard to do.
Therefore, use just a single mutex for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frames that failed PLCP error checks are most likely
microwave transmissions (well, maybe not ...) and
don't have a proper rate detected, so ignore it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running in client mode and associating to an AP, the channel
change is usually performed with the offchannel flag still set.
However after the assoc is complete, the following channel change event
is suppressed because the run time channel is already set to the operating channel.
Fix this by sending channel change notifications to the driver even if
only the offchannel flag changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides a little more flexibility for human users, and it allows
us to use isalpha rather than the custom is_alpha_upper.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remote_tx_win is intended to be set on receipt of an L2CAP
configuration request. The value is used to determine the size of the
transmit window on the remote side of an ERTM connection, so L2CAP
can stop sending frames when that remote window is full.
An incorrect remote_tx_win value will cause the stack to not fully
utilize the tx window (performance impact), or to overfill the remote
tx window (causing dropped frames or a disconnect).
This patch removes an extra setting of remote_tx_win when a
configuration response is received. The transmit window has a
different meaning in a response - it is an informational value
less than or equal to the local tx_win.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Incoming configuration values must be converted to native CPU order
before use. This fixes a bug where a little-endian MPS value is
compared to a native CPU value. On big-endian processors, this
can cause ERTM and streaming mode segmentation to produce PDUs
that are larger than the remote stack is expecting, or that would
produce fragmented skbs that the current FCS code cannot handle.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Accesses to "wdev->current_bss" must be
locked with the wdev lock, which action
frame transmission is missing.
Cc: stable@kernel.org [2.6.33+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since there was added ->tcf_chain() method without ->bind_tcf() to
sch_sfq class options, there is oops when a filter is added with
the classid parameter.
Fixes commit 7d2681a6ff
netdev thread: null pointer at cls_api.c
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Franchoze Eric <franchoze@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although netif_rx() isn't expected to be called in process context with
preemption enabled, it'd better handle this case. And this is why get_cpu()
is used in the non-RPS #ifdef branch. If tree RCU is selected,
rcu_read_lock() won't disable preemption, so preempt_disable() should be
called explictly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.
Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_on() check in __napi_gro_receive() skips part of the
"common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(),
where at least eth header should be copied for entirely paged skbs.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get
call->state_lock so that it can alter the state of an RxRPC call. However, its
caller (call_timer_fn()) has an apparent lock on the timer struct.
The problem is that rxrpc_resend_time_expired() isn't permitted to lock
call->state_lock as this could cause a deadlock against rxrpc_send_abort() as
that takes state_lock and then attempts to delete the resend timer by calling
del_timer_sync().
The deadlock can occur because del_timer_sync() will sit there forever waiting
for rxrpc_resend_time_expired() to return, but the latter may then wait for
call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()...
This leads to a warning appearing in the kernel log that looks something like
the attached.
It should be sufficient to simply dispense with the locks. It doesn't matter
if we set the resend timer expired event bit and queue the event processor
whilst we're changing state to one where the resend timer is irrelevant as the
event can just be ignored by the processor thereafter.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35-rc3-cachefs+ #115
-------------------------------------------------------
swapper/0 is trying to acquire lock:
(&call->state_lock){++--..}, at: [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
but task is already holding lock:
(&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&call->resend_timer){+.-...}:
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffff8103bb9c>] del_timer_sync+0x3c/0x86
[<ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc]
[<ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc]
[<ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs]
[<ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs]
[<ffffffff8104261d>] worker_thread+0x1ef/0x2e2
[<ffffffff81045f47>] kthread+0x7a/0x82
[<ffffffff81002cd4>] kernel_thread_helper+0x4/0x10
-> #0 (&call->state_lock){++--..}:
[<ffffffff81055237>] validate_chain+0x727/0xd23
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<ffffffff81036828>] __do_softirq+0xa2/0x13e
[<ffffffff81002dcc>] call_softirq+0x1c/0x28
[<ffffffff810049f0>] do_softirq+0x38/0x80
[<ffffffff810361a2>] irq_exit+0x45/0x47
[<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
[<ffffffff810011ac>] cpu_idle+0x4d/0x83
[<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
other info that might help us debug this:
1 lock held by swapper/0:
#0: (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5
stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115
Call Trace:
<IRQ> [<ffffffff81054414>] print_circular_bug+0xae/0xbd
[<ffffffff81055237>] validate_chain+0x727/0xd23
[<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
[<ffffffff810539a7>] ? mark_lock+0x42f/0x51f
[<ffffffff81056184>] lock_acquire+0x57/0x6d
[<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
[<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
[<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
[<ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5
[<ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc]
[<ffffffff810367ef>] ? __do_softirq+0x69/0x13e
[<ffffffff81036828>] __do_softirq+0xa2/0x13e
[<ffffffff81002dcc>] call_softirq+0x1c/0x28
[<ffffffff810049f0>] do_softirq+0x38/0x80
[<ffffffff810361a2>] irq_exit+0x45/0x47
[<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
[<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
<EOI> [<ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86
[<ffffffff8100955b>] ? mwait_idle+0x6e/0x78
[<ffffffff81009552>] ? mwait_idle+0x65/0x78
[<ffffffff810011ac>] cpu_idle+0x4d/0x83
[<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length should be checked before the packet data is dereferenced.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the TX path, skb->data points to the ethernet header, not the network
header. So when validating the packet length for accessing we should
take the ethernet header into account.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning is:
net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
Check result code of L2CAP information response. Otherwise
it would read invalid feature mask and access invalid memory.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the remote side doesn't support Enhanced Retransmission Mode neither
Streaming Mode, we shall not send the RFC option.
Some devices that only supports Basic Mode do not understanding the RFC
option. This patch fixes the regression found with these devices.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit fc6055a5ba (net: Introduce
skb_orphan_try()) allows an early orphan of the skb and takes care on
tx timestamping, which needs the sk-reference in the skb on driver level.
So does the can-raw socket, which has not been taken into account here.
The patch below adds a 'prevent_sk_orphan' bit in the skb tx shared info,
which fixes the problem discovered by Matthias Fuchs here:
http://marc.info/?t=128030411900003&r=1&w=2
Even if it's not a primary tx timestamp topic it fits well into some skb
shared tx context. Or should be find a different place for the information to
protect the sk reference until it reaches the driver level?
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 15e83ed788.
As explained by Johannes Berg, the optimization made here is
invalid. Or, at best, incomplete.
Not only destructor invocation, but conntract entry releasing
must be executed outside of hw IRQ context.
So just checking "skb->destructor" is insufficient.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ab95bfe01f replaces bridge and macvlan
hooks in __netif_receive_skb(), so dev.c doesn't need to include their headers.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to use a negative offset in a u32 match to reference
the ethernet header or other parts of the link layer header.
This fixes the regression caused by:
commit fbc2e7d9cf
Author: Changli Gao <xiaosuo@gmail.com>
Date: Wed Jun 2 07:32:42 2010 -0700
cls_u32: use skb_header_pointer() to dereference data safely
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6c79bf0f24 subtracts PPPOE_SES_HLEN from mtu at
the front of ip_fragment(). So the later subtraction should be removed. The
MTU of 802.1q is also 1500, so MTU should not be changed.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.bo>
----
net/ipv4/ip_output.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: Bart De Schuymer <bdschuym@pandora.bo>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial TCP thin-stream commit did not add getsockopt support for the new
socket options: TCP_THIN_LINEAR_TIMEOUTS and TCP_THIN_DUPACK. This adds support
for them.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Tested-by: Andreas Petlund <apetlund@simula.no>
Acked-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
9P spec says:
"It is correct to consider remove to be a clunk with the
side effect of removing the file if permissions allow. "
So even if remove fails we need to destroy the fid.
Without this patch an rmdir on a directory with contents leave
the new cloned directory fid fid attached to fidlist. On umount
we dump the fids on the fidlist
~# rmdir /mnt2/test4/
rmdir: failed to remove `/mnt2/test4/': Directory not empty
~# umount /mnt2/
~# dmesg
[ 228.474323] Found fid 3 not clunked
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
TXATTRCREATE: Prepare a fid for setting xattr value on a file system object.
size[4] TXATTRCREATE tag[2] fid[4] name[s] attr_size[8] flags[4]
size[4] RXATTRCREATE tag[2]
txattrcreate gets a fid pointing to xattr. This fid can later be
used to set the xattr value.
flag value is derived from set Linux setxattr. The manpage says
"The flags parameter can be used to refine the semantics of the operation.
XATTR_CREATE specifies a pure create, which fails if the named attribute
exists already. XATTR_REPLACE specifies a pure replace operation, which
fails if the named attribute does not already exist. By default (no flags),
the extended attribute will be created if need be, or will simply replace
the value if the attribute exists."
The actual setxattr operation happens when the fid is clunked. At that point
the written byte count and the attr_size specified in TXATTRCREATE should be
same otherwise an error will be returned.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
TXATTRWALK: Descend a ATTR namespace
size[4] TXATTRWALK tag[2] fid[4] newfid[4] name[s]
size[4] RXATTRWALK tag[2] size[8]
txattrwalk gets a fid pointing to xattr. This fid can later be
used to read the xattr value. If name is NULL the fid returned
can be used to get the list of extended attribute associated to
the file system object.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Implement 9p2000.L version of open(LOPEN) interface in 9p client.
For LOPEN, no need to convert the flags to and from 9p mode to VFS mode.
Synopsis:
size[4] Tlopen tag[2] fid[4] mode[4]
size[4] Rlopen tag[2] qid[13] iounit[4]
[Fix mode bit format - jvrao@linux.vnet.ibm.com]
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbegren <ericvh@gmail.com>
SYNOPSIS
size[4] Tlcreate tag[2] fid[4] name[s] flags[4] mode[4] gid[4]
size[4] Rlcreate tag[2] qid[13] iounit[4]
DESCRIPTION
The Tlreate request asks the file server to create a new regular file with the
name supplied, in the directory (dir) represented by fid.
The mode argument specifies the permissions to use. New file is created with
the uid if the fid and with supplied gid.
The flags argument represent Linux access mode flags with which the caller
is requesting to open the file with. Protocol allows all the Linux access
modes but it is upto the server to allow/disallow any of these acess modes.
If the server doesn't support any of the access mode, it is expected to
return error.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Implement TMKDIR as part of 2000.L Work
Synopsis
size[4] Tmkdir tag[2] fid[4] name[s] mode[4] gid[4]
size[4] Rmkdir tag[2] qid[13]
Description
mkdir asks the file server to create a directory with given name,
mode and gid. The qid for the new directory is returned with
the mkdir reply message.
Note: 72 is selected as the opcode for TMKDIR from the reserved list.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] Tmknod tag[2] fid[4] name[s] mode[4] major[4] minor[4] gid[4]
size[4] Rmknod tag[2] qid[13]
Description
mknod asks the file server to create a device node with given major and
minor number, mode and gid. The qid for the new device node is returned
with the mknod reply message.
[sripathik@in.ibm.com: Fix error handling code]
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Create a symbolic link
SYNOPSIS
size[4] Tsymlink tag[2] fid[4] name[s] symtgt[s] gid[4]
size[4] Rsymlink tag[2] qid[13]
DESCRIPTION
Create a symbolic link named 'name' pointing to 'symtgt'.
gid represents the effective group id of the caller.
The permissions of a symbolic link are irrelevant hence it is omitted
from the protocol.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Reviewed-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch adds a helper function to get the dentry from inode and
uses it in creating a Hardlink
SYNOPSIS
size[4] Tlink tag[2] dfid[4] oldfid[4] newpath[s]
size[4] Rlink tag[2]
DESCRIPTION
Create a link 'newpath' in directory pointed by dfid linking to oldfid path.
[sripathik@in.ibm.com : p9_client_link should not free req structure
if p9_client_rpc has returned an error.]
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
