The current scheme of using the timer tick was fine for per-thread
events. However, it was causing bias issues in system-wide mode
(including for uncore PMUs). Event groups would not get their fair
share of runtime on the PMU. With tickless kernels, if a core is idle
there is no timer tick, and thus no event rotation (multiplexing).
However, there are events (especially uncore events) which do count
even though cores are asleep.
This patch changes the timer source for multiplexing. It introduces a
per-PMU per-cpu hrtimer. The advantage is that even when a core goes
idle, it will come back to service the hrtimer, thus multiplexing on
system-wide events works much better.
The per-PMU implementation (suggested by PeterZ) enables adjusting the
multiplexing interval per PMU. The preferred interval is stashed into
the struct pmu. If not set, it will be forced to the default interval
value.
In order to minimize the impact of the hrtimer, it is turned on and
off on demand. When the PMU on a CPU is overcommited, the hrtimer is
activated. It is stopped when the PMU is not overcommitted.
In order for this to work properly, we had to change the order of
initialization in start_kernel() such that hrtimer_init() is run
before perf_event_init().
The default interval in milliseconds is set to a timer tick just like
with the old code. We will provide a sysctl to tune this in another
patch.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/r/1364991694-5876-2-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull 'full dynticks' support from Ingo Molnar:
"This tree from Frederic Weisbecker adds a new, (exciting! :-) core
kernel feature to the timer and scheduler subsystems: 'full dynticks',
or CONFIG_NO_HZ_FULL=y.
This feature extends the nohz variable-size timer tick feature from
idle to busy CPUs (running at most one task) as well, potentially
reducing the number of timer interrupts significantly.
This feature got motivated by real-time folks and the -rt tree, but
the general utility and motivation of full-dynticks runs wider than
that:
- HPC workloads get faster: CPUs running a single task should be able
to utilize a maximum amount of CPU power. A periodic timer tick at
HZ=1000 can cause a constant overhead of up to 1.0%. This feature
removes that overhead - and speeds up the system by 0.5%-1.0% on
typical distro configs even on modern systems.
- Real-time workload latency reduction: CPUs running critical tasks
should experience as little jitter as possible. The last remaining
source of kernel-related jitter was the periodic timer tick.
- A single task executing on a CPU is a pretty common situation,
especially with an increasing number of cores/CPUs, so this feature
helps desktop and mobile workloads as well.
The cost of the feature is mainly related to increased timer
reprogramming overhead when a CPU switches its tick period, and thus
slightly longer to-idle and from-idle latency.
Configuration-wise a third mode of operation is added to the existing
two NOHZ kconfig modes:
- CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
as a config option. This is the traditional Linux periodic tick
design: there's a HZ tick going on all the time, regardless of
whether a CPU is idle or not.
- CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
periodic tick when a CPU enters idle mode.
- CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
tick when a CPU is idle, also slows the tick down to 1 Hz (one
timer interrupt per second) when only a single task is running on a
CPU.
The .config behavior is compatible: existing !CONFIG_NO_HZ and
CONFIG_NO_HZ=y settings get translated to the new values, without the
user having to configure anything. CONFIG_NO_HZ_FULL is turned off by
default.
This feature is based on a lot of infrastructure work that has been
steadily going upstream in the last 2-3 cycles: related RCU support
and non-periodic cputime support in particular is upstream already.
This tree adds the final pieces and activates the feature. The pull
request is marked RFC because:
- it's marked 64-bit only at the moment - the 32-bit support patch is
small but did not get ready in time.
- it has a number of fresh commits that came in after the merge
window. The overwhelming majority of commits are from before the
merge window, but still some aspects of the tree are fresh and so I
marked it RFC.
- it's a pretty wide-reaching feature with lots of effects - and
while the components have been in testing for some time, the full
combination is still not very widely used. That it's default-off
should reduce its regression abilities and obviously there are no
known regressions with CONFIG_NO_HZ_FULL=y enabled either.
- the feature is not completely idempotent: there is no 100%
equivalent replacement for a periodic scheduler/timer tick. In
particular there's ongoing work to map out and reduce its effects
on scheduler load-balancing and statistics. This should not impact
correctness though, there are no known regressions related to this
feature at this point.
- it's a pretty ambitious feature that with time will likely be
enabled by most Linux distros, and we'd like you to make input on
its design/implementation, if you dislike some aspect we missed.
Without flaming us to crisp! :-)
Future plans:
- there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
the periodic tick altogether when there's a single busy task on a
CPU. We'd first like 1 Hz to be exposed more widely before we go
for the 0 Hz target though.
- once we reach 0 Hz we can remove the periodic tick assumption from
nr_running>=2 as well, by essentially interrupting busy tasks only
as frequently as the sched_latency constraints require us to do -
once every 4-40 msecs, depending on nr_running.
I am personally leaning towards biting the bullet and doing this in
v3.10, like the -rt tree this effort has been going on for too long -
but the final word is up to you as usual.
More technical details can be found in Documentation/timers/NO_HZ.txt"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
sched: Keep at least 1 tick per second for active dynticks tasks
rcu: Fix full dynticks' dependency on wide RCU nocb mode
nohz: Protect smp_processor_id() in tick_nohz_task_switch()
nohz_full: Add documentation.
cputime_nsecs: use math64.h for nsec resolution conversion helpers
nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
nohz: Reduce overhead under high-freq idling patterns
nohz: Remove full dynticks' superfluous dependency on RCU tree
nohz: Fix unavailable tick_stop tracepoint in dynticks idle
nohz: Add basic tracing
nohz: Select wide RCU nocb for full dynticks
nohz: Disable the tick when irq resume in full dynticks CPU
nohz: Re-evaluate the tick for the new task after a context switch
nohz: Prepare to stop the tick on irq exit
nohz: Implement full dynticks kick
nohz: Re-evaluate the tick from the scheduler IPI
sched: New helper to prevent from stopping the tick in full dynticks
sched: Kick full dynticks CPU that have more than one task enqueued.
perf: New helper to prevent full dynticks CPUs from stopping tick
perf: Kick full dynticks CPU if events rotation is needed
...
Commit 0637e02939
("nohz: Select wide RCU nocb for full dynticks") intended
to force CONFIG_RCU_NOCB_CPU_ALL=y when full dynticks is
enabled.
However this option is part of a choice menu and Kconfig's
"select" instruction has no effect on such targets.
Fix this by using reverse dependencies on the targets we
don't want instead.
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
The full dynticks tree needs the latest RCU and sched
upstream updates in order to fix some dependencies.
Merge a common upstream merge point that has these
updates.
Conflicts:
include/linux/perf_event.h
kernel/rcutree.h
kernel/rcutree_plugin.h
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Split the proc namespace stuff out into linux/proc_ns.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: netdev@vger.kernel.org
cc: Serge E. Hallyn <serge.hallyn@ubuntu.com>
cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit f91eb62f71 ("init: scream bloody murder if interrupts are
enabled too early") added three new warnings. The first two seemed
reasonable, but the third included a warning when an initcall returned
non-zero. Although, the third WARN() does include an imbalanced preempt
disabled, or irqs disable, it shouldn't warn if it only had an initcall
that just returns non-zero.
In fact, according to Linus, it shouldn't print at all. As it only
prints with initcall_debug set, and that already shows enough
information to fix things.
Link: http://lkml.kernel.org/r/CA+55aFzaBC5SFi7=F2mfm+KWY5qTsBmOqgbbs8E+LUS8JK-sBg@mail.gmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kconfig language requires that dependent options all follow the
menuconfig symbol in order to be collapsed below it. Recently some hidden
options were added below the EXPERT menuconfig, but did not depend on
EXPERT (because hidden options can't). This broke the display. So
re-order all these options, and while we're here stick the PCI quirks
under the EXPERT menu (since it isn't sitting with any related options).
Before this commit, we get:
[*] Configure standard kernel features (expert users) --->
[ ] Sysctl syscall support
[*] Load all symbols for debugging/ksymoops
...
[ ] Embedded system
Now we get the older (and correct) behavior:
[*] Configure standard kernel features (expert users) --->
[ ] Embedded system
And if you go into the expert menu you get the expert options:
[ ] Sysctl syscall support
[*] Load all symbols for debugging/ksymoops
...
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the only users of call_usermodehelper_fns(). This function
suffers from not being able to determine if the cleanup is called. Even
if in this places the cleanup pointer is NULL, convert them to use the
separate call_usermodehelper_setup() + call_usermodehelper_exec()
functions so we can remove the _fns variant.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull core timer updates from Ingo Molnar:
"The main changes in this cycle's merge are:
- Implement shadow timekeeper to shorten in kernel reader side
blocking, by Thomas Gleixner.
- Posix timers enhancements by Pavel Emelyanov:
- allocate timer ID per process, so that exact timer ID allocations
can be re-created be checkpoint/restore code.
- debuggability and tooling (/proc/PID/timers, etc.) improvements.
- suspend/resume enhancements by Feng Tang: on certain new Intel Atom
processors (Penwell and Cloverview), there is a feature that the
TSC won't stop in S3 state, so the TSC value won't be reset to 0
after resume. This can be taken advantage of by the generic via
the CLOCK_SOURCE_SUSPEND_NONSTOP flag: instead of using the RTC to
recover/approximate sleep time, the main (and precise) clocksource
can be used.
- Fix /proc/timer_list for 4096 CPUs by Nathan Zimmer: on so many
CPUs the file goes beyond 4MB of size and thus the current
simplistic seqfile approach fails. Convert /proc/timer_list to a
proper seq_file with its own iterator.
- Cleanups and refactorings of the core timekeeping code by John
Stultz.
- International Atomic Clock time is managed by the NTP code
internally currently but not exposed externally. Separate the TAI
code out and add CLOCK_TAI support and TAI support to the hrtimer
and posix-timer code, by John Stultz.
- Add deep idle support enhacement to the broadcast clockevents core
timer code, by Daniel Lezcano: add an opt-in CLOCK_EVT_FEAT_DYNIRQ
clockevents feature (which will be utilized by future clockevents
driver updates), which allows the use of IRQ affinities to avoid
spurious wakeups of idle CPUs - the right CPU with an expiring
timer will be woken.
- Add new ARM bcm281xx clocksource driver, by Christian Daudt
- ... various other fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
clockevents: Set dummy handler on CPU_DEAD shutdown
timekeeping: Update tk->cycle_last in resume
posix-timers: Remove unused variable
clockevents: Switch into oneshot mode even if broadcast registered late
timer_list: Convert timer list to be a proper seq_file
timer_list: Split timer_list_show_tickdevices
posix-timers: Show sigevent info in proc file
posix-timers: Introduce /proc/PID/timers file
posix timers: Allocate timer id per process (v2)
timekeeping: Make sure to notify hrtimers when TAI offset changes
hrtimer: Fix ktime_add_ns() overflow on 32bit architectures
hrtimer: Add expiry time overflow check in hrtimer_interrupt
timekeeping: Shorten seq_count region
timekeeping: Implement a shadow timekeeper
timekeeping: Delay update of clock->cycle_last
timekeeping: Store cycle_last value in timekeeper struct as well
ntp: Remove ntp_lock, using the timekeeping locks to protect ntp state
timekeeping: Simplify tai updating from do_adjtimex
timekeeping: Hold timekeepering locks in do_adjtimex and hardpps
timekeeping: Move ADJ_SETOFFSET to top level do_adjtimex()
...
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
Pull scheduler changes from Ingo Molnar:
"The main changes in this development cycle were:
- full dynticks preparatory work by Frederic Weisbecker
- factor out the cpu time accounting code better, by Li Zefan
- multi-CPU load balancer cleanups and improvements by Joonsoo Kim
- various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
sched: Fix init NOHZ_IDLE flag
sched: Prevent to re-select dst-cpu in load_balance()
sched: Rename load_balance_tmpmask to load_balance_mask
sched: Move up affinity check to mitigate useless redoing overhead
sched: Don't consider other cpus in our group in case of NEWLY_IDLE
sched: Explicitly cpu_idle_type checking in rebalance_domains()
sched: Change position of resched_cpu() in load_balance()
sched: Fix wrong rq's runnable_avg update with rt tasks
sched: Document task_struct::personality field
sched/cpuacct/UML: Fix header file dependency bug on the UML build
cgroup: Kill subsys.active flag
sched/cpuacct: No need to check subsys active state
sched/cpuacct: Initialize cpuacct subsystem earlier
sched/cpuacct: Initialize root cpuacct earlier
sched/cpuacct: Allocate per_cpu cpuusage for root cpuacct statically
sched/cpuacct: Clean up cpuacct.h
sched/cpuacct: Remove redundant NULL checks in cpuacct_acount_field()
sched/cpuacct: Remove redundant NULL checks in cpuacct_charge()
sched/cpuacct: Add cpuacct_acount_field()
sched/cpuacct: Add cpuacct_init()
...
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle are mostly related to preparatory work
for the full-dynticks work:
- Remove restrictions on no-CBs CPUs, make RCU_FAST_NO_HZ take
advantage of numbered callbacks, do callback accelerations based on
numbered callbacks. Posted to LKML at
https://lkml.org/lkml/2013/3/18/960
- RCU documentation updates. Posted to LKML at
https://lkml.org/lkml/2013/3/18/570
- Miscellaneous fixes. Posted to LKML at
https://lkml.org/lkml/2013/3/18/594"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rcu: Make rcu_accelerate_cbs() note need for future grace periods
rcu: Abstract rcu_start_future_gp() from rcu_nocb_wait_gp()
rcu: Rename n_nocb_gp_requests to need_future_gp
rcu: Push lock release to rcu_start_gp()'s callers
rcu: Repurpose no-CBs event tracing to future-GP events
rcu: Rearrange locking in rcu_start_gp()
rcu: Make RCU_FAST_NO_HZ take advantage of numbered callbacks
rcu: Accelerate RCU callbacks at grace-period end
rcu: Export RCU_FAST_NO_HZ parameters to sysfs
rcu: Distinguish "rcuo" kthreads by RCU flavor
rcu: Add event tracing for no-CBs CPUs' grace periods
rcu: Add event tracing for no-CBs CPUs' callback registration
rcu: Introduce proper blocking to no-CBs kthreads GP waits
rcu: Provide compile-time control for no-CBs CPUs
rcu: Tone down debugging during boot-up and shutdown.
rcu: Add softirq-stall indications to stall-warning messages
rcu: Documentation update
rcu: Make bugginess of code sample more evident
rcu: Fix hlist_bl_set_first_rcu() annotation
rcu: Delete unused rcu_node "wakemask" field
...
Also enables cleanup of some 80-col trickery.
Cc: Richard Weinberger <richard@nod.at>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel was booted with the "quiet" boot option we have currently no
chance to see why an initrd fails. Change KERN_WARNING to KERN_ERR to see
what is going on.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As I was testing a lot of my code recently, and having several
"successes", I accidentally noticed in the dmesg this little line:
start_kernel(): bug: interrupts were enabled *very* early, fixing it
Sure enough, one of my patches two commits ago enabled interrupts early.
The sad part here is that I never noticed it, and I ran several tests with
ktest too, and ktest did not notice this line.
What ktest looks for (and so does many other automated testing scripts) is
a back trace produced by a WARN_ON() or BUG(). As a back trace was never
produced, my buggy patch could have slipped into linux-next, or even
worse, mainline.
Adding a WARN(!irqs_disabled()) makes this bug a little more obvious:
PID hash table entries: 4096 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2003252k/2054848k available (4857k kernel code, 460k absent, 51136k reserved, 6210k data, 1096k init)
------------[ cut here ]------------
WARNING: at /home/rostedt/work/git/linux-trace.git/init/main.c:543 start_kernel+0x21e/0x415()
Hardware name: To Be Filled By O.E.M.
Interrupts were enabled *very* early, fixing it
Modules linked in:
Pid: 0, comm: swapper/0 Not tainted 3.8.0-test+ #286
Call Trace:
warn_slowpath_common+0x83/0x9b
warn_slowpath_fmt+0x46/0x48
start_kernel+0x21e/0x415
x86_64_start_reservations+0x10e/0x112
x86_64_start_kernel+0x102/0x111
---[ end trace 007d8b0491b4f5d8 ]---
Preemptible hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
NR_IRQS:4352 nr_irqs:712 16
Console: colour VGA+ 80x25
console [ttyS0] enabled, bootconsole disabled
Do you see it?
The original version of this patch just slapped a WARN_ON() in there and
kept the printk(). Ard van Breemen suggested using the WARN() interface,
which makes the code a bit cleaner.
Also, while examining other warnings in init/main.c, I found two other
locations that deserve a bloody murder scream if their conditions are hit,
and updated them accordingly.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ard van Breemen <ard@telegraafnet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Turn the full dynticks passive dependency on VIRT_CPU_ACCOUNTING_GEN
to an active one.
The full dynticks Kconfig is currently hidden behind the full dynticks
cputime accounting, which is an awkward and counter-intuitive layout:
the user first has to select the dynticks cputime accounting in order
to make the full dynticks feature to be visible.
We definetly want it the other way around. The usual way to perform
this kind of active dependency is use "select" on the depended target.
Now we can't use the Kconfig "select" instruction when the target is
a "choice".
So this patch inspires on how the RCU subsystem Kconfig interact
with its dependencies on SMP and PREEMPT: we make sure that cputime
accounting can't propose another option than VIRT_CPU_ACCOUNTING_GEN
when NO_HZ_FULL is selected by using the right "depends on" instruction
for each cputime accounting choices.
v2: Keep full dynticks cputime accounting available even without
full dynticks, as per Paul McKenney's suggestion.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
We need full dynticks CPU to also be RCU nocb so
that we don't have to keep the tick to handle RCU
callbacks.
Make sure the range passed to nohz_full= boot
parameter is a subset of rcu_nocbs=
The CPUs that fail to meet this requirement will be
excluded from the nohz_full range. This is checked
early in boot time, before any CPU has the opportunity
to stop its tick.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Pull RCU updates from Paul E. McKenney:
* Remove restrictions on no-CBs CPUs, make RCU_FAST_NO_HZ
take advantage of numbered callbacks, do additional callback
accelerations based on numbered callbacks. Posted to LKML
at https://lkml.org/lkml/2013/3/18/960.
* RCU documentation updates. Posted to LKML at
https://lkml.org/lkml/2013/3/18/570.
* Miscellaneous fixes. Posted to LKML at
https://lkml.org/lkml/2013/3/18/594.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For now this calls cpu_idle(), but in the long run we want to move the
cpu bringup code to the core and therefor we add a state argument.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130321215233.583190032@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We are planning to convert the dynticks Kconfig options layout
into a choice menu. The user must be able to easily pick
any of the following implementations: constant periodic tick,
idle dynticks, full dynticks.
As this implies a mutual exclusion, the two dynticks implementions
need to converge on the selection of a common Kconfig option in order
to ease the sharing of a common infrastructure.
It would thus seem pretty natural to reuse CONFIG_NO_HZ to
that end. It already implements all the idle dynticks code
and the full dynticks depends on all that code for now.
So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and
CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ.
On the other hand we want to stay backward compatible: if
CONFIG_NO_HZ is set in an older config file, we want to
enable CONFIG_NO_HZ_IDLE by default.
But we can't afford both at the same time or we run into
a circular dependency:
1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select
CONFIG_NO_HZ
2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE
We might be able to support that from Kconfig/Kbuild but it
may not be wise to introduce such a confusing behaviour.
So to solve this, create a new CONFIG_NO_HZ_COMMON option
which gathers the common code between idle and full dynticks
(that common code for now is simply the idle dynticks code)
and select it from their referring Kconfig.
Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ
to it for backward compatibility.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Because RCU callbacks are now associated with the number of the grace
period that they must wait for, CPUs can now take advance callbacks
corresponding to grace periods that ended while a given CPU was in
dyntick-idle mode. This eliminates the need to try forcing the RCU
state machine while entering idle, thus reducing the CPU intensiveness
of RCU_FAST_NO_HZ, which should increase its energy efficiency.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, the per-no-CBs-CPU kthreads are named "rcuo" followed by
the CPU number, for example, "rcuo". This is problematic given that
there are either two or three RCU flavors, each of which gets a per-CPU
kthread with exactly the same name. This commit therefore introduces
a one-letter abbreviation for each RCU flavor, namely 'b' for RCU-bh,
'p' for RCU-preempt, and 's' for RCU-sched. This abbreviation is used
to distinguish the "rcuo" kthreads, for example, for CPU 0 we would have
"rcuob/0", "rcuop/0", and "rcuos/0".
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Currently, the only way to specify no-CBs CPUs is via the rcu_nocbs
kernel command-line parameter. This is inconvenient in some cases,
particularly for randconfig testing, so this commit adds a new set of
kernel configuration parameters. CONFIG_RCU_NOCB_CPU_NONE (the default)
retains the old behavior, CONFIG_RCU_NOCB_CPU_ZERO offloads callback
processing from CPU 0 (along with any other CPUs specified by the
rcu_nocbs boot-time parameter), and CONFIG_RCU_NOCB_CPU_ALL offloads
callback processing from all CPUs.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Remove "config EXPERIMENTAL" itself, now that every "depends on" it has
been removed from the tree.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, CPU 0 is constrained to not be a no-CBs CPU, and furthermore
at least one no-CBs CPU must remain online at any given time. These
restrictions are problematic in some situations, such as cases where
all CPUs must run a real-time workload that needs to be insulated from
OS jitter and latencies due to RCU callback invocation. This commit
therefore provides no-CBs CPUs a (very crude and energy-inefficient)
way to start and to wait for grace periods independently of the normal
RCU callback mechanisms. This approach allows any or all of the CPUs to
be designated as no-CBs CPUs, and allows any proper subset of the CPUs
(whether no-CBs CPUs or not) to be offlined.
This commit also provides a fix for a locking bug spotted by Xie
ChanglongX <changlongx.xie@intel.com>.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Until we provide the nohz_mask boot parameter, keeping
the context tracking probes disabled by default is pointless
since what we want is to runtime test this code anyway.
It's furthermore confusing for the users which don't expect
the probes to be off when they select RCU user mode or full
dynticks cputime accounting.
Let's enable these probes selftests by default for now.
Suggested: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mats Liljegren <mats.liljegren@enea.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
To convert the clockevents code to cpumask_var_t we need to move the
init call after the allocator setup.
Clockevents are earliest registered from time_init() as they need
interrupts being set up, so this is safe.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130306111537.304379448@linutronix.de
Cc: Rusty Russell <rusty@rustcorp.com.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NKkW
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull new ARC architecture from Vineet Gupta:
"Initial ARC Linux port with some fixes on top for 3.9-rc1:
I would like to introduce the Linux port to ARC Processors (from
Synopsys) for 3.9-rc1. The patch-set has been discussed on the public
lists since Nov and has received a fair bit of review, specially from
Arnd, tglx, Al and other subsystem maintainers for DeviceTree, kgdb...
The arch bits are in arch/arc, some asm-generic changes (acked by
Arnd), a minor change to PARISC (acked by Helge).
The series is a touch bigger for a new port for 2 main reasons:
1. It enables a basic kernel in first sub-series and adds
ptrace/kgdb/.. later
2. Some of the fallout of review (DeviceTree support, multi-platform-
image support) were added on top of orig series, primarily to
record the revision history.
This updated pull request additionally contains
- fixes due to our GNU tools catching up with the new syscall/ptrace
ABI
- some (minor) cross-arch Kconfig updates."
* tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (82 commits)
ARC: split elf.h into uapi and export it for userspace
ARC: Fixup the current ABI version
ARC: gdbserver using regset interface possibly broken
ARC: Kconfig cleanup tracking cross-arch Kconfig pruning in merge window
ARC: make a copy of flat DT
ARC: [plat-arcfpga] DT arc-uart bindings change: "baud" => "current-speed"
ARC: Ensure CONFIG_VIRT_TO_BUS is not enabled
ARC: Fix pt_orig_r8 access
ARC: [3.9] Fallout of hlist iterator update
ARC: 64bit RTSC timestamp hardware issue
ARC: Don't fiddle with non-existent caches
ARC: Add self to MAINTAINERS
ARC: Provide a default serial.h for uart drivers needing BASE_BAUD
ARC: [plat-arcfpga] defconfig for fully loaded ARC Linux
ARC: [Review] Multi-platform image #8: platform registers SMP callbacks
ARC: [Review] Multi-platform image #7: SMP common code to use callbacks
ARC: [Review] Multi-platform image #6: cpu-to-dma-addr optional
ARC: [Review] Multi-platform image #5: NR_IRQS defined by ARC core
ARC: [Review] Multi-platform image #4: Isolate platform headers
ARC: [Review] Multi-platform image #3: switch to board callback
...
Pull user namespace and namespace infrastructure changes from Eric W Biederman:
"This set of changes starts with a few small enhnacements to the user
namespace. reboot support, allowing more arbitrary mappings, and
support for mounting devpts, ramfs, tmpfs, and mqueuefs as just the
user namespace root.
I do my best to document that if you care about limiting your
unprivileged users that when you have the user namespace support
enabled you will need to enable memory control groups.
There is a minor bug fix to prevent overflowing the stack if someone
creates way too many user namespaces.
The bulk of the changes are a continuation of the kuid/kgid push down
work through the filesystems. These changes make using uids and gids
typesafe which ensures that these filesystems are safe to use when
multiple user namespaces are in use. The filesystems converted for
3.9 are ceph, 9p, afs, ocfs2, gfs2, ncpfs, nfs, nfsd, and cifs. The
changes for these filesystems were a little more involved so I split
the changes into smaller hopefully obviously correct changes.
XFS is the only filesystem that remains. I was hoping I could get
that in this release so that user namespace support would be enabled
with an allyesconfig or an allmodconfig but it looks like the xfs
changes need another couple of days before it they are ready."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (93 commits)
cifs: Enable building with user namespaces enabled.
cifs: Convert struct cifs_ses to use a kuid_t and a kgid_t
cifs: Convert struct cifs_sb_info to use kuids and kgids
cifs: Modify struct smb_vol to use kuids and kgids
cifs: Convert struct cifsFileInfo to use a kuid
cifs: Convert struct cifs_fattr to use kuid and kgids
cifs: Convert struct tcon_link to use a kuid.
cifs: Modify struct cifs_unix_set_info_args to hold a kuid_t and a kgid_t
cifs: Convert from a kuid before printing current_fsuid
cifs: Use kuids and kgids SID to uid/gid mapping
cifs: Pass GLOBAL_ROOT_UID and GLOBAL_ROOT_GID to keyring_alloc
cifs: Use BUILD_BUG_ON to validate uids and gids are the same size
cifs: Override unmappable incoming uids and gids
nfsd: Enable building with user namespaces enabled.
nfsd: Properly compare and initialize kuids and kgids
nfsd: Store ex_anon_uid and ex_anon_gid as kuids and kgids
nfsd: Modify nfsd4_cb_sec to use kuids and kgids
nfsd: Handle kuids and kgids in the nfs4acl to posix_acl conversion
nfsd: Convert nfsxdr to use kuids and kgids
nfsd: Convert nfs3xdr to use kuids and kgids
...
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull async changes from Tejun Heo:
"These are followups for the earlier deadlock issue involving async
ending up waiting for itself through block requesting module[1]. The
following changes are made by these commits.
- Instead of requesting default elevator on each request_queue init,
block now requests it once early during boot.
- Kmod triggers warning if invoked from an async worker.
- Async synchronization implementation has been reimplemented. It's
a lot simpler now."
* 'for-3.9-async' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
async: initialise list heads to fix crash
async: replace list of active domains with global list of pending items
async: keep pending tasks on async_domain and remove async_pending
async: use ULLONG_MAX for infinity cookie value
async: bring sanity to the use of words domain and running
async, kmod: warn on synchronous request_module() from async workers
block: don't request module during elevator init
init, block: try to load default elevator module early during boot
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Pull irq core changes from Ingo Molnar:
"The biggest changes are the IRQ-work and printk changes from Frederic
Weisbecker, which prepare the code for 'full dynticks' (the ability to
stop or slow down the periodic tick arbitrarily, not just in idle time
as today):
- Don't stop tick with irq works pending. This fix is generally
useful and concerns archs that can't raise self IPIs.
- Flush irq works before CPU offlining.
- Introduce "lazy" irq works that can wait for the next tick to be
executed, unless it's stopped.
- Implement klogd wake up using irq work. This removes the ad-hoc
printk_tick()/printk_needs_cpu() hooks and make it working even in
dynticks mode.
- Cleanups and fixes."
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Export enable/disable_percpu_irq()
arch Kconfig: Remove references to IRQ_PER_CPU
irq_work: Remove return value from the irq_work_queue() function
genirq: Avoid deadlock in spurious handling
printk: Wake up klogd using irq_work
irq_work: Make self-IPIs optable
irq_work: Warn if there's still work on cpu_down
irq_work: Flush work on CPU_DYING
irq_work: Don't stop the tick with pending works
nohz: Add API to check tick state
irq_work: Remove CONFIG_HAVE_IRQ_WORK
irq_work: Fix racy check on work pending flag
irq_work: Fix racy IRQ_WORK_BUSY flag setting
PARISC defines /proc/sys/kernel/unaligned-trap to runtime toggle
unaligned access emulation.
The exact mechanics of enablig/disabling are still arch specific, we can
make the sysctl usable by other arches.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Now that the kuids and kgids conversion have propogated
through net/sunrpc/ and the fs/nfsd/ it is safe to enable
building nfsd when user namespaces are enabled.
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that the kuids and kgids conversion have propogated
through net/sunrpc/ and the fs/nfs/ it is safe to enable
building nfs when user namespaces are enabled.
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
ncpfs does not natively support uids and gids so this conversion was
simply a matter of updating the the type of the mounteduid, the uid
and the gid on the superblock. Fixing the ioctls that read them,
updating the mount option parser and the mount option printer.
Cc: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that all of the necessary work has been done to push kuids and
kgids throughout gfs2 and to convert between kuids and kgids when
reading and writing the on disk structures it is safe to enable gfs2
when multiple user namespaces are enabled.
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that ocfs2 has been converted to store uids and gids in
kuid_t and kgid_t and all of the conversions have been added
to the appropriate places it is safe to allow building and
using ocfs2 with user namespace support enabled.
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that the coda kernel to userspace has been modified to convert
between kuids and kgids and uids and gids, and all internal
coda structures have be modified to store uids and gids as
kuids and kgids it is safe to allow code to be built with
user namespace support enabled.
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Modify struct afs_file_status to store owner as a kuid_t and group as
a kgid_t.
In xdr_decode_AFSFetchStatus as owner is now a kuid_t and group is now
a kgid_t don't use the EXTRACT macro. Instead perform the work of
the extract macro explicitly. Read the value with ntohl and
convert it to the appropriate type with make_kuid or make_kgid.
Test if the value is different from what is stored in status and
update changed. Update the value in status.
In xdr_encode_AFS_StoreStatus call from_kuid or from_kgid as
we are computing the on the wire encoding.
Initialize uids with GLOBAL_ROOT_UID instead of 0.
Initialize gids with GLOBAL_ROOT_GID instead of 0.
Cc: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that the uid_t -> kuid_t, gid_t -> kgid_t conversion
has been completed in 9p allow 9p to be built when user
namespaces are enabled.
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that conversions happen from kuids and kgids when generating ceph
messages and conversion happen to kuids and kgids after receiving
celph messages, and all intermediate data structures store uids and
gids as type kuid_t and kgid_t it is safe to enable ceph with
user namespace support enabled.
Cc: Sage Weil <sage@inktank.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the sysctl-related bits from include/linux/sched.h into
a new file: include/linux/sched/sysctl.h. Then update source
files requiring access to those bits by including the new
header file.
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094659.06dced96@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1Tzp
-----END PGP SIGNATURE-----
Merge tag 'full-dynticks-cputime-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into sched/core
Pull full-dynticks (user-space execution is undisturbed and
receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready,
from Frederic Weisbecker:
"This implements the cputime accounting on full dynticks CPUs.
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user."
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
kernel/irq_work.c
Add support for printk in full dynticks CPU.
* Don't stop tick with irq works pending. This
fix is generally useful and concerns archs that
can't raise self IPIs.
* Flush irq works before CPU offlining.
* Introduce "lazy" irq works that can wait for the
next tick to be executed, unless it's stopped.
* Implement klogd wake up using irq work. This
removes the ad-hoc printk_tick()/printk_needs_cpu()
hooks and make it working even in dynticks mode.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The TINY_PREEMPT_RCU is complex, does not provide that much memory
savings, and therefore TREE_PREEMPT_RCU should be used instead. The
systems where the difference between TINY_PREEMPT_RCU and TREE_PREEMPT_RCU
are quite small compared to the memory footprint of CONFIG_PREEMPT.
This commit therefore takes a first step towards eliminating
TINY_PREEMPT_RCU by allowing TREE_PREEMPT_RCU to be configured on !SMP
systems.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Tiny RCU has historically omitted RCU CPU stall warnings in order to
reduce memory requirements, however, lack of these warnings caused
Thomas Gleixner some debugging pain recently. Therefore, this commit
adds RCU CPU stall warnings to tiny RCU if RCU_TRACE=y. This keeps
the memory footprint small, while still enabling CPU stall warnings
in kernels built to enable them.
Updated to include Josh Triplett's suggested use of RCU_STALL_COMMON
config variable to simplify #if expressions.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
If we want to stop the tick further idle, we need to be
able to account the cputime without using the tick.
Virtual based cputime accounting solves that problem by
hooking into kernel/user boundaries.
However implementing CONFIG_VIRT_CPU_ACCOUNTING require
low level hooks and involves more overhead. But we already
have a generic context tracking subsystem that is required
for RCU needs by archs which plan to shut down the tick
outside idle.
This patch implements a generic virtual based cputime
accounting that relies on these generic kernel/user hooks.
There are some upsides of doing this:
- This requires no arch code to implement CONFIG_VIRT_CPU_ACCOUNTING
if context tracking is already built (already necessary for RCU in full
tickless mode).
- We can rely on the generic context tracking subsystem to dynamically
(de)activate the hooks, so that we can switch anytime between virtual
and tick based accounting. This way we don't have the overhead
of the virtual accounting when the tick is running periodically.
And one downside:
- There is probably more overhead than a native virtual based cputime
accounting. But this relies on hooks that are already set anyway.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
In the help text describing user namespaces recommend use of memory
control groups. In many cases memory control groups are the only
mechanism there is to limit how much memory a user who can create
user namespaces can use.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
To allow the builder to sign only a subset of modules, or to sign the
modules using a key that is not available on the build machine, add
CONFIG_MODULE_SIG_ALL. If this option is unset, no modules will be
signed during build. The default is 'y', to preserve the current
behavior.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull misc syscall fixes from Al Viro:
- compat syscall fixes (discussed back in December)
- a couple of "make life easier for sigaltstack stuff by reducing
inter-tree dependencies"
- fix up compiler/asmlinkage calling convention disagreement of
sys_clone()
- misc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
sys_clone() needs asmlinkage_protect
make sure that /linuxrc has std{in,out,err}
x32: fix sigtimedwait
x32: fix waitid()
switch compat_sys_wait4() and compat_sys_waitid() to COMPAT_SYSCALL_DEFINE
switch compat_sys_sigaltstack() to COMPAT_SYSCALL_DEFINE
CONFIG_GENERIC_SIGALTSTACK build breakage with asm-generic/syscalls.h
Ensure that kernel_init_freeable() is not inlined into non __init code
This patch adds default module loading and uses it to load the default
block elevator. During boot, it's called right after initramfs or
initrd is made available and right before control is passed to
userland. This ensures that as long as the modules are available in
the usual places in initramfs, initrd or the root filesystem, the
default modules are loaded as soon as possible.
This will replace the on-demand elevator module loading from elevator
init path.
v2: Fixed build breakage when !CONFIG_BLOCK. Reported by kbuild test
robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Fengguang We <fengguang.wu@intel.com>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 281dc5c5ec ("Give up on pushing CC_OPTIMIZE_FOR_SIZE") we
already changed the actual default value, but the help-text still
suggested 'y'. Fix the help text too, for all the same reasons.
Sadly, -Os keeps on generating some very suboptimal code for certain
cases, to the point where any I$ miss upside is swamped by the downside.
The main ones are:
- using "rep movsb" for memcpy, even on CPU's where that is
horrendously bad for performance.
- not honoring branch prediction information, so any I$ footprint you
win from smaller code, you lose from less code density in the I$.
- using divide instructions when that is very expensive.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Serge Hallyn <serge.hallyn@canonical.com>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@ubuntu.com>
This config item has not carried much meaning for a while now and is
almost always enabled by default (especially in distro builds). As agreed
during the Linux kernel summit, it should be removed. As a first step,
remove it from being listed, and default it to on. Once it has been
removed from all subsystem Kconfigs, it will be dropped entirely.
For items that really are experimental, maintainers should use "default
n", optionally include "(EXPERIMENTAL)" in the title, and add language to
the help text indicating why the item should be considered experimental.
For items that are dangerously experimental, the maintainer is encouraged
to follow the above title recommendation, add stronger language to the
help text, and optionally use (depending on the extent of the danger,
from least to most dangerous): printk(), add_taint(TAINT_WARN),
add_taint(TAINT_CRAP), WARN_ON(1), and CONFIG_BROKEN.
CC: Greg KH <gregkh@linuxfoundation.org>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Serge Hallyn <serge.hallyn@canonical.com>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
IA64 defines /proc/sys/kernel/ignore-unaligned-usertrap to control
verbose warnings on unaligned access emulation.
Although the exact mechanics of what to do with sysctl (ignore/shout)
are arch specific, this change enables the sysctl to be usable cross-arch.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit d6b2123802 "make sure that we always have a return path from
kernel_execve()" reshuffled kernel_init()/init_post() to ensure that
kernel_execve() has a caller to return to.
It removed __init annotation for kernel_init() and introduced/calls a
new routine kernel_init_freeable(). Latter however is inlined by any
reasonable compiler (ARC gcc 4.4 in this case), causing slight code
bloat.
This patch forces kernel_init_freeable() as noinline reducing the .text
bloat-o-meter vmlinux vmlinux_new
add/remove: 1/0 grow/shrink: 0/1 up/down: 374/-334 (40)
function old new delta
kernel_init_freeable - 374 +374 (.init.text)
kernel_init 628 294 -334 (.text)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull signal handling cleanups from Al Viro:
"sigaltstack infrastructure + conversion for x86, alpha and um,
COMPAT_SYSCALL_DEFINE infrastructure.
Note that there are several conflicts between "unify
SS_ONSTACK/SS_DISABLE definitions" and UAPI patches in mainline;
resolution is trivial - just remove definitions of SS_ONSTACK and
SS_DISABLED from arch/*/uapi/asm/signal.h; they are all identical and
include/uapi/linux/signal.h contains the unified variant."
Fixed up conflicts as per Al.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to generic sigaltstack
new helpers: __save_altstack/__compat_save_altstack, switch x86 and um to those
generic compat_sys_sigaltstack()
introduce generic sys_sigaltstack(), switch x86 and um to it
new helper: compat_user_stack_pointer()
new helper: restore_altstack()
unify SS_ONSTACK/SS_DISABLE definitions
new helper: current_user_stack_pointer()
missing user_stack_pointer() instances
Bury the conditionals from kernel_thread/kernel_execve series
COMPAT_SYSCALL_DEFINE: infrastructure
All architectures have
CONFIG_GENERIC_KERNEL_THREAD
CONFIG_GENERIC_KERNEL_EXECVE
__ARCH_WANT_SYS_EXECVE
None of them have __ARCH_WANT_KERNEL_EXECVE and there are only two callers
of kernel_execve() (which is a trivial wrapper for do_execve() now) left.
Kill the conditionals and make both callers use do_execve().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The page allocator is able to bind a page to a memcg when it is
allocated. But for the caches, we'd like to have as many objects as
possible in a page belonging to the same cache.
This is done in this patch by calling memcg_kmem_get_cache in the
beginning of every allocation function. This function is patched out by
static branches when kernel memory controller is not being used.
It assumes that the task allocating, which determines the memcg in the
page allocator, belongs to the same cgroup throughout the whole process.
Misaccounting can happen if the task calls memcg_kmem_get_cache() while
belonging to a cgroup, and later on changes. This is considered
acceptable, and should only happen upon task migration.
Before the cache is created by the memcg core, there is also a possible
imbalance: the task belongs to a memcg, but the cache being allocated from
is the global cache, since the child cache is not yet guaranteed to be
ready. This case is also fine, since in this case the GFP_KMEMCG will not
be passed and the page allocator will not attempt any cgroup accounting.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: JoonSoo Kim <js1304@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the basic infrastructure for the accounting of kernel memory. To
control that, the following files are created:
* memory.kmem.usage_in_bytes
* memory.kmem.limit_in_bytes
* memory.kmem.failcnt
* memory.kmem.max_usage_in_bytes
They have the same meaning of their user memory counterparts. They
reflect the state of the "kmem" res_counter.
Per cgroup kmem memory accounting is not enabled until a limit is set for
the group. Once the limit is set the accounting cannot be disabled for
that group. This means that after the patch is applied, no behavioral
changes exists for whoever is still using memcg to control their memory
usage, until memory.kmem.limit_in_bytes is set for the first time.
We always account to both user and kernel resource_counters. This
effectively means that an independent kernel limit is in place when the
limit is set to a lower value than the user memory. A equal or higher
value means that the user limit will always hit first, meaning that kmem
is effectively unlimited.
People who want to track kernel memory but not limit it, can set this
limit to a very high number (like RESOURCE_MAX - 1page - that no one will
ever hit, or equal to the user memory)
[akpm@linux-foundation.org: MEMCG_MMEM only works with slab and slub]
Signed-off-by: Glauber Costa <glommer@parallels.com>
Acked-by: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: JoonSoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespace changes from Eric Biederman:
"While small this set of changes is very significant with respect to
containers in general and user namespaces in particular. The user
space interface is now complete.
This set of changes adds support for unprivileged users to create user
namespaces and as a user namespace root to create other namespaces.
The tyranny of supporting suid root preventing unprivileged users from
using cool new kernel features is broken.
This set of changes completes the work on setns, adding support for
the pid, user, mount namespaces.
This set of changes includes a bunch of basic pid namespace
cleanups/simplifications. Of particular significance is the rework of
the pid namespace cleanup so it no longer requires sending out
tendrils into all kinds of unexpected cleanup paths for operation. At
least one case of broken error handling is fixed by this cleanup.
The files under /proc/<pid>/ns/ have been converted from regular files
to magic symlinks which prevents incorrect caching by the VFS,
ensuring the files always refer to the namespace the process is
currently using and ensuring that the ptrace_mayaccess permission
checks are always applied.
The files under /proc/<pid>/ns/ have been given stable inode numbers
so it is now possible to see if different processes share the same
namespaces.
Through the David Miller's net tree are changes to relax many of the
permission checks in the networking stack to allowing the user
namespace root to usefully use the networking stack. Similar changes
for the mount namespace and the pid namespace are coming through my
tree.
Two small changes to add user namespace support were commited here adn
in David Miller's -net tree so that I could complete the work on the
/proc/<pid>/ns/ files in this tree.
Work remains to make it safe to build user namespaces and 9p, afs,
ceph, cifs, coda, gfs2, ncpfs, nfs, nfsd, ocfs2, and xfs so the
Kconfig guard remains in place preventing that user namespaces from
being built when any of those filesystems are enabled.
Future design work remains to allow root users outside of the initial
user namespace to mount more than just /proc and /sys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (38 commits)
proc: Usable inode numbers for the namespace file descriptors.
proc: Fix the namespace inode permission checks.
proc: Generalize proc inode allocation
userns: Allow unprivilged mounts of proc and sysfs
userns: For /proc/self/{uid,gid}_map derive the lower userns from the struct file
procfs: Print task uids and gids in the userns that opened the proc file
userns: Implement unshare of the user namespace
userns: Implent proc namespace operations
userns: Kill task_user_ns
userns: Make create_new_namespaces take a user_ns parameter
userns: Allow unprivileged use of setns.
userns: Allow unprivileged users to create new namespaces
userns: Allow setting a userns mapping to your current uid.
userns: Allow chown and setgid preservation
userns: Allow unprivileged users to create user namespaces.
userns: Ignore suid and sgid on binaries if the uid or gid can not be mapped
userns: fix return value on mntns_install() failure
vfs: Allow unprivileged manipulation of the mount namespace.
vfs: Only support slave subtrees across different user namespaces
vfs: Add a user namespace reference from struct mnt_namespace
...
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ivQa
-----END PGP SIGNATURE-----
Merge tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma
Pull Automatic NUMA Balancing bare-bones from Mel Gorman:
"There are three implementations for NUMA balancing, this tree
(balancenuma), numacore which has been developed in tip/master and
autonuma which is in aa.git.
In almost all respects balancenuma is the dumbest of the three because
its main impact is on the VM side with no attempt to be smart about
scheduling. In the interest of getting the ball rolling, it would be
desirable to see this much merged for 3.8 with the view to building
scheduler smarts on top and adapting the VM where required for 3.9.
The most recent set of comparisons available from different people are
mel: https://lkml.org/lkml/2012/12/9/108
mingo: https://lkml.org/lkml/2012/12/7/331
tglx: https://lkml.org/lkml/2012/12/10/437
srikar: https://lkml.org/lkml/2012/12/10/397
The results are a mixed bag. In my own tests, balancenuma does
reasonably well. It's dumb as rocks and does not regress against
mainline. On the other hand, Ingo's tests shows that balancenuma is
incapable of converging for this workloads driven by perf which is bad
but is potentially explained by the lack of scheduler smarts. Thomas'
results show balancenuma improves on mainline but falls far short of
numacore or autonuma. Srikar's results indicate we all suffer on a
large machine with imbalanced node sizes.
My own testing showed that recent numacore results have improved
dramatically, particularly in the last week but not universally.
We've butted heads heavily on system CPU usage and high levels of
migration even when it shows that overall performance is better.
There are also cases where it regresses. Of interest is that for
specjbb in some configurations it will regress for lower numbers of
warehouses and show gains for higher numbers which is not reported by
the tool by default and sometimes missed in treports. Recently I
reported for numacore that the JVM was crashing with
NullPointerExceptions but currently it's unclear what the source of
this problem is. Initially I thought it was in how numacore batch
handles PTEs but I'm no longer think this is the case. It's possible
numacore is just able to trigger it due to higher rates of migration.
These reports were quite late in the cycle so I/we would like to start
with this tree as it contains much of the code we can agree on and has
not changed significantly over the last 2-3 weeks."
* tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma: (50 commits)
mm/rmap, migration: Make rmap_walk_anon() and try_to_unmap_anon() more scalable
mm/rmap: Convert the struct anon_vma::mutex to an rwsem
mm: migrate: Account a transhuge page properly when rate limiting
mm: numa: Account for failed allocations and isolations as migration failures
mm: numa: Add THP migration for the NUMA working set scanning fault case build fix
mm: numa: Add THP migration for the NUMA working set scanning fault case.
mm: sched: numa: Delay PTE scanning until a task is scheduled on a new node
mm: sched: numa: Control enabling and disabling of NUMA balancing if !SCHED_DEBUG
mm: sched: numa: Control enabling and disabling of NUMA balancing
mm: sched: Adapt the scanning rate if a NUMA hinting fault does not migrate
mm: numa: Use a two-stage filter to restrict pages being migrated for unlikely task<->node relationships
mm: numa: migrate: Set last_nid on newly allocated page
mm: numa: split_huge_page: Transfer last_nid on tail page
mm: numa: Introduce last_nid to the page frame
sched: numa: Slowly increase the scanning period as NUMA faults are handled
mm: numa: Rate limit setting of pte_numa if node is saturated
mm: numa: Rate limit the amount of memory that is migrated between nodes
mm: numa: Structures for Migrate On Fault per NUMA migration rate limiting
mm: numa: Migrate pages handled during a pmd_numa hinting fault
mm: numa: Migrate on reference policy
...
This reverts commit bd52276fa1 ("x86-64/efi: Use EFI to deal with
platform wall clock (again)"), and the two supporting commits:
da5a108d05: "x86/kernel: remove tboot 1:1 page table creation code"
185034e72d: "x86, efi: 1:1 pagetable mapping for virtual EFI calls")
as they all depend semantically on commit 53b87cf088 ("x86, mm:
Include the entire kernel memory map in trampoline_pgd") that got
reverted earlier due to the problems it caused.
This was pointed out by Yinghai Lu, and verified by me on my Macbook Air
that uses EFI.
Pointed-out-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 EFI update from Peter Anvin:
"EFI tree, from Matt Fleming. Most of the patches are the new efivarfs
filesystem by Matt Garrett & co. The balance are support for EFI
wallclock in the absence of a hardware-specific driver, and various
fixes and cleanups."
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
efivarfs: Make efivarfs_fill_super() static
x86, efi: Check table header length in efi_bgrt_init()
efivarfs: Use query_variable_info() to limit kmalloc()
efivarfs: Fix return value of efivarfs_file_write()
efivarfs: Return a consistent error when efivarfs_get_inode() fails
efivarfs: Make 'datasize' unsigned long
efivarfs: Add unique magic number
efivarfs: Replace magic number with sizeof(attributes)
efivarfs: Return an error if we fail to read a variable
efi: Clarify GUID length calculations
efivarfs: Implement exclusive access for {get,set}_variable
efivarfs: efivarfs_fill_super() ensure we clean up correctly on error
efivarfs: efivarfs_fill_super() ensure we free our temporary name
efivarfs: efivarfs_fill_super() fix inode reference counts
efivarfs: efivarfs_create() ensure we drop our reference on inode on error
efivarfs: efivarfs_file_read ensure we free data in error paths
x86-64/efi: Use EFI to deal with platform wall clock (again)
x86/kernel: remove tboot 1:1 page table creation code
x86, efi: 1:1 pagetable mapping for virtual EFI calls
x86, mm: Include the entire kernel memory map in trampoline_pgd
...
N_HIGH_MEMORY stands for the nodes that has normal or high memory.
N_MEMORY stands for the nodes that has any memory.
The code here need to handle with the nodes which have memory, we should
use N_MEMORY instead.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Lin Feng <linfeng@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds Kconfig options and kernel parameters to allow the
enabling and disabling of automatic NUMA balancing. The existance
of such a switch was and is very important when debugging problems
related to transparent hugepages and we should have the same for
automatic NUMA placement.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Implement pte_numa and pmd_numa.
We must atomically set the numa bit and clear the present bit to
define a pte_numa or pmd_numa.
Once a pte or pmd has been set as pte_numa or pmd_numa, the next time
a thread touches a virtual address in the corresponding virtual range,
a NUMA hinting page fault will trigger. The NUMA hinting page fault
will clear the NUMA bit and set the present bit again to resolve the
page fault.
The expectation is that a NUMA hinting page fault is used as part
of a placement policy that decides if a page should remain on the
current node or migrated to a different node.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Conflicts:
arch/x86/kernel/ptrace.c
Pull the latest RCU tree from Paul E. McKenney:
" The major features of this series are:
1. A first version of no-callbacks CPUs. This version prohibits
offlining CPU 0, but only when enabled via CONFIG_RCU_NOCB_CPU=y.
Relaxing this constraint is in progress, but not yet ready
for prime time. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/724, and are at branch rcu/nocb.
2. Changes to SRCU that allows statically initialized srcu_struct
structures. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/296, and are at branch rcu/srcu.
3. Restructuring of RCU's debugfs output. These commits were posted
to LKML at https://lkml.org/lkml/2012/10/30/341, and are at
branch rcu/tracing.
4. Additional CPU-hotplug/RCU improvements, posted to LKML at
https://lkml.org/lkml/2012/10/30/327, and are at branch rcu/hotplug.
Note that the commit eliminating __stop_machine() was judged to
be too-high of risk, so is deferred to 3.9.
5. Changes to RCU's idle interface, most notably a new module
parameter that redirects normal grace-period operations to
their expedited equivalents. These were posted to LKML at
https://lkml.org/lkml/2012/10/30/739, and are at branch rcu/idle.
6. Additional diagnostics for RCU's CPU stall warning facility,
posted to LKML at https://lkml.org/lkml/2012/10/30/315, and
are at branch rcu/stall. The most notable change reduces the
default RCU CPU stall-warning time from 60 seconds to 21 seconds,
so that it once again happens sooner than the softlockup timeout.
7. Documentation updates, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/280, and are at branch rcu/doc.
A couple of late-breaking changes were posted at
https://lkml.org/lkml/2012/11/16/634 and
https://lkml.org/lkml/2012/11/16/547.
8. Miscellaneous fixes, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/309, along with a late-breaking
change posted at Fri, 16 Nov 2012 11:26:25 -0800 with message-ID
<20121116192625.GA447@linux.vnet.ibm.com>, but which lkml.org
seems to have missed. These are at branch rcu/fixes.
9. Finally, a fix for an lockdep-RCU splat was posted to LKML
at https://lkml.org/lkml/2012/11/7/486. This is at rcu/next. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Create a new subsystem that probes on kernel boundaries
to keep track of the transitions between level contexts
with two basic initial contexts: user or kernel.
This is an abstraction of some RCU code that use such tracking
to implement its userspace extended quiescent state.
We need to pull this up from RCU into this new level of indirection
because this tracking is also going to be used to implement an "on
demand" generic virtual cputime accounting. A necessary step to
shutdown the tick while still accounting the cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[ paulmck: fix whitespace error and email address. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The MSDOS/MBR partition table includes a 32-bit unique ID, often referred
to as the NT disk signature. When combined with a partition number within
the table, this can form a unique ID similar in concept to EFI/GPT's
partition UUID. Constructing and recording this value in struct
partition_meta_info allows MSDOS partitions to be referred to on the
kernel command-line using the following syntax:
root=PARTUUID=0002dd75-01
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reduce the minimum length for a root=PARTUUID= parameter to be considered
valid from 36 to 1. EFI/GPT partition UUIDs are always exactly 36
characters long, hence the previous limit. However, the next patch will
support DOS/MBR UUIDs too, which have a different, shorter, format.
Instead of validating any particular length, just ensure that at least
some non-empty value was given by the user.
Also, consider a missing UUID value to be a parsing error, in the same
vein as if /PARTNROFF exists and can't be parsed. As such, make both
error cases print a message and disable rootwait. Convert to pr_err while
we're at it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will allow other types of UUID to be stored here, aside from true
UUIDs. This also simplifies code that uses this field, since it's usually
constructed from a, used as a, or compared to other, strings.
Note: A simplistic approach here would be to set uuid_str[36]=0 whenever a
/PARTNROFF option was found to be present. However, this modifies the
input string, and causes subsequent calls to devt_from_partuuid() not to
see the /PARTNROFF option, which causes different results. In order to
avoid misleading future maintainers, this parameter is marked const.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Assign a unique proc inode to each namespace, and use that
inode number to ensure we only allocate at most one proc
inode for every namespace in proc.
A single proc inode per namespace allows userspace to test
to see if two processes are in the same namespace.
This has been a long requested feature and only blocked because
a naive implementation would put the id in a global space and
would ultimately require having a namespace for the names of
namespaces, making migration and certain virtualization tricks
impossible.
We still don't have per superblock inode numbers for proc, which
appears necessary for application unaware checkpoint/restart and
migrations (if the application is using namespace file descriptors)
but that is now allowd by the design if it becomes important.
I have preallocated the ipc and uts initial proc inode numbers so
their structures can be statically initialized.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Instead of setting child_reaper and SIGNAL_UNKILLABLE one way
for the system init process, and another way for pid namespace
init processes test pid->nr == 1 and use the same code for both.
For the global init this results in SIGNAL_UNKILLABLE being set
much earlier in the initialization process.
This is a small cleanup and it paves the way for allowing unshare and
enter of the pid namespace as that path like our global init also will
not set CLONE_NEWPID.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
klogd is woken up asynchronously from the tick in order
to do it safely.
However if printk is called when the tick is stopped, the reader
won't be woken up until the next interrupt, which might not fire
for a while. As a result, the user may miss some message.
To fix this, lets implement the printk tick using a lazy irq work.
This subsystem takes care of the timer tick state and can
fix up accordingly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
irq work can run on any arch even without IPI
support because of the hook on update_process_times().
So lets remove HAVE_IRQ_WORK because it doesn't reflect
any backend requirement.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
RCU callback execution can add significant OS jitter and also can
degrade both scheduling latency and, in asymmetric multiprocessors,
energy efficiency. This commit therefore adds the ability for selected
CPUs ("rcu_nocbs=" boot parameter) to have their callbacks offloaded
to kthreads. If the "rcu_nocb_poll" boot parameter is also specified,
these kthreads will do polling, removing the need for the offloaded
CPUs to do wakeups. At least one CPU must be doing normal callback
processing: currently CPU 0 cannot be selected as a no-CBs CPU.
In addition, attempts to offline the last normal-CBs CPU will fail.
This feature was inspired by Jim Houston's and Joe Korty's JRCU, and
this commit includes fixes to problems located by Fengguang Wu's
kbuild test robot.
[ paulmck: Added gfp.h include file as suggested by Fengguang Wu. ]
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Use kuid_t and kgid_t in struct fuse_conn and struct fuse_mount_data.
The connection between between a fuse filesystem and a fuse daemon is
established when a fuse filesystem is mounted and provided with a file
descriptor the fuse daemon created by opening /dev/fuse.
For now restrict the communication of uids and gids between the fuse
filesystem and the fuse daemon to the initial user namespace. Enforce
this by verifying the file descriptor passed to the mount of fuse was
opened in the initial user namespace. Ensuring the mount happens in
the initial user namespace is not necessary as mounts from non-initial
user namespaces are not yet allowed.
In fuse_req_init_context convert the currrent fsuid and fsgid into the
initial user namespace for the request that will be sent to the fuse
daemon.
In fuse_fill_attr convert the uid and gid passed from the fuse daemon
from the initial user namespace into kuids and kgids.
In iattr_to_fattr called from fuse_setattr convert kuids and kgids
into the uids and gids in the initial user namespace before passing
them to the fuse filesystem.
In fuse_change_attributes_common called from fuse_dentry_revalidate,
fuse_permission, fuse_geattr, and fuse_setattr, and fuse_iget convert
the uid and gid from the fuse daemon into a kuid and a kgid to store
on the fuse inode.
By default fuse mounts are restricted to task whose uid, suid, and
euid matches the fuse user_id and whose gid, sgid, and egid matches
the fuse group id. Convert the user_id and group_id mount options
into kuids and kgids at mount time, and use uid_eq and gid_eq to
compare the in fuse_allow_task.
Cc: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Use kuid_t and kgid_t in struct autofs_info and struct autofs_wait_queue.
When creating directories and symlinks default the uid and gid of
the mount requester to the global root uid and gid. autofs4_wait
will update these fields when a mount is requested.
When generating autofsv5 packets report the uid and gid of the mount
requestor in user namespace of the process that opened the pipe,
reporting unmapped uids and gids as overflowuid and overflowgid.
In autofs_dev_ioctl_requester return the uid and gid of the last mount
requester converted into the calling processes user namespace. When the
uid or gid don't map return overflowuid and overflowgid as appropriate,
allowing failure to find a mount requester to be distinguished from
failure to map a mount requester.
The uid and gid mount options specifying the user and group of the
root autofs inode are converted into kuid and kgid as they are parsed
defaulting to the current uid and current gid of the process that
mounts autofs.
Mounting of autofs for the present remains confined to processes in
the initial user namespace.
Cc: Ian Kent <raven@themaw.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy
thread_info_cache_init() gets inlined into start_kernel().
Signed-off-by: David Howells <dhowells@redhat.com>
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
History:
This commit was originally merged as bacef661ac ("x86-64/efi:
Use EFI to deal with platform wall clock") but it resulted in some
ASUS machines no longer booting due to a firmware bug, and so was
reverted in f026cfa82f. A pre-emptive fix for the buggy ASUS
firmware was merged in 03a1c254975e ("x86, efi: 1:1 pagetable
mapping for virtual EFI calls") so now this patch can be
reapplied.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com> [added commit history]
This commit adds a "try" missing from the end of the first paragraph
of the RCU_USER_QS help text.
[ paulmck: Also fix up the last paragraph a bit. ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The RCU_FAST_NO_HZ help text included a warning about overhead on large
systems, but that issue has since been resolved. The main remaining
issue with RCU_FAST_NO_HZ is increased real-time latency. This commit
therefore updates the help text accordingly.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Pull third pile of VFS updates from Al Viro:
"Stuff from Jeff Layton, mostly. Sanitizing interplay between audit
and namei, removing a lot of insanity from audit_inode() mess and
getting things ready for his ESTALE patchset."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
vfs: unexport getname and putname symbols
acct: constify the name arg to acct_on
vfs: allocate page instead of names_cache buffer in mount_block_root
audit: overhaul __audit_inode_child to accomodate retrying
audit: optimize audit_compare_dname_path
audit: make audit_compare_dname_path use parent_len helper
audit: remove dirlen argument to audit_compare_dname_path
audit: set the name_len in audit_inode for parent lookups
audit: add a new "type" field to audit_names struct
audit: reverse arguments to audit_inode_child
audit: no need to walk list in audit_inode if name is NULL
audit: pass in dentry to audit_copy_inode wherever possible
audit: remove unnecessary NULL ptr checks from do_path_lookup
* allow kernel_execve() leave the actual return to userland to
caller (selected by CONFIG_GENERIC_KERNEL_EXECVE). Callers
updated accordingly.
* architecture that does select GENERIC_KERNEL_EXECVE in its
Kconfig should have its ret_from_kernel_thread() do this:
call schedule_tail
call the callback left for it by copy_thread(); if it ever
returns, that's because it has just done successful kernel_execve()
jump to return from syscall
IOW, its only difference from ret_from_fork() is that it does call the
callback.
* such an architecture should also get rid of ret_from_kernel_execve()
and __ARCH_WANT_KERNEL_EXECVE
This is the last part of infrastructure patches in that area - from
that point on work on different architectures can live independently.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull RCU fixes from Ingo Molnar:
"This tree includes a shutdown/cpu-hotplug deadlock fix and a
documentation fix."
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Advise most users not to enable RCU user mode
rcu: Grace-period initialization excludes only RCU notifier
First, it's incorrect to call putname() after __getname_gfp() since the
bare __getname_gfp() call skips the auditing code, while putname()
doesn't.
mount_block_root allocates a PATH_MAX buffer via __getname_gfp, and then
calls get_fs_names to fill the buffer. That function can call
get_filesystem_list which assumes that that buffer is a full page in
size. On arches where PAGE_SIZE != 4k, then this could potentially
overrun.
In practice, it's hard to imagine the list of filesystem names even
approaching 4k, but it's best to be safe. Just allocate a page for this
purpose instead.
With this, we can also remove the __getname_gfp() definition since there
are no more callers.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only place where kernel_execve() is called without a way to
return to the caller of kernel_thread() callback is kernel_post().
Reorganize kernel_init()/kernel_post() - instead of the former
calling the latter in the end (and getting freed by it), have the
latter *begin* with calling the former (and turn the latter into
kernel_thread() callback, of course).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Discourage distros from enabling CONFIG_RCU_USER_QS
because it brings overhead for no benefits yet.
It's not a useful feature on its own until we can
fully run an adaptive tickless kernel.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Check the signature on the module against the keys compiled into the kernel or
available in a hardware key store.
Currently, only RSA keys are supported - though that's easy enough to change,
and the signature is expected to contain raw components (so not a PGP or
PKCS#7 formatted blob).
The signature blob is expected to consist of the following pieces in order:
(1) The binary identifier for the key. This is expected to match the
SubjectKeyIdentifier from an X.509 certificate. Only X.509 type
identifiers are currently supported.
(2) The signature data, consisting of a series of MPIs in which each is in
the format of a 2-byte BE word sizes followed by the content data.
(3) A 12 byte information block of the form:
struct module_signature {
enum pkey_algo algo : 8;
enum pkey_hash_algo hash : 8;
enum pkey_id_type id_type : 8;
u8 __pad;
__be32 id_length;
__be32 sig_length;
};
The three enums are defined in crypto/public_key.h.
'algo' contains the public-key algorithm identifier (0->DSA, 1->RSA).
'hash' contains the digest algorithm identifier (0->MD4, 1->MD5, 2->SHA1,
etc.).
'id_type' contains the public-key identifier type (0->PGP, 1->X.509).
'__pad' should be 0.
'id_length' should contain in the binary identifier length in BE form.
'sig_length' should contain in the signature data length in BE form.
The lengths are in BE order rather than CPU order to make dealing with
cross-compilation easier.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (minor Kconfig fix)
Provide kernel configuration options for module signing.
The following configuration options are added:
CONFIG_MODULE_SIG_SHA1
CONFIG_MODULE_SIG_SHA224
CONFIG_MODULE_SIG_SHA256
CONFIG_MODULE_SIG_SHA384
CONFIG_MODULE_SIG_SHA512
These select the cryptographic hash used to digest the data prior to signing.
Additionally, the crypto module selected will be built into the kernel as it
won't be possible to load it as a module without incurring a circular
dependency when the kernel tries to check its signature.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We do a very simple search for a particular string appended to the module
(which is cache-hot and about to be SHA'd anyway). There's both a config
option and a boot parameter which control whether we accept or fail with
unsigned modules and modules that are signed with an unknown key.
If module signing is enabled, the kernel will be tainted if a module is
loaded that is unsigned or has a signature for which we don't have the
key.
(Useful feedback and tweaks by David Howells <dhowells@redhat.com>)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
After both prio_tree users have been converted to use red-black trees,
there is no need to keep around the prio tree library anymore.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce SYSCTL_EXCEPTION_TRACE config option and selec it in the
architectures requiring support for the "exception-trace" debug_table
entry in kernel/sysctl.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_UID16 config option and select it in corresponding
architecture Kconfig files. UID16 now only depends on HAVE_UID16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a simple ASN.1 grammar compiler. This produces a bytecode output that can
be fed to a decoder to inform the decoder how to interpret the ASN.1 stream it
is trying to parse.
Action functions can be specified in the grammar by interpolating:
({ foo })
after a type, for example:
SubjectPublicKeyInfo ::= SEQUENCE {
algorithm AlgorithmIdentifier,
subjectPublicKey BIT STRING ({ do_key_data })
}
The decoder is expected to call these after matching this type and parsing the
contents if it is a constructed type.
The grammar compiler does not currently support the SET type (though it does
support SET OF) as I can't see a good way of tracking which members have been
encountered yet without using up extra stack space.
Currently, the grammar compiler will fail if more than 256 bytes of bytecode
would be produced or more than 256 actions have been specified as it uses
8-bit jump values and action indices to keep space usage down.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Adds an expert Kconfig option, CONFIG_COREDUMP, which allows disabling of
core dump. This saves approximately 2.6k in the compiled kernel, and
complements CONFIG_ELF_CORE, which now depends on it.
CONFIG_COREDUMP also disables coredump-related sysctls, except for
suid_dumpable and related functions, which are necessary for ptrace.
[akpm@linux-foundation.org: fix binfmt_aout.c build]
Signed-off-by: Alex Kelly <alex.page.kelly@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PA-RISC tool chain seems to have some problem with correct
read/write attributes on sections. This causes problems when the const
sections are fixed up for other architecture to only contain truly
read-only data.
Disable const sections for PA-RISC
This can cause a bit of noise with modpost.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago), and
some hyper-v updates and some printk fixes as well. All patches that
are outside of the drivers/base area have been acked by the respective
maintainers, and have all been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3vkACgkQMUfUDdst+ylQoACgldktGFgkCLzH+rGYthrXOC5P
9hUAnjmOhdoHlMTL81vWTlH+BrGernym
=khrr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
Features currently supported:
- 39-bit address space for user and kernel (each)
- 4KB and 64KB page configurations
- Compat (32-bit) user applications (ARMv7, EABI only)
- Flattened Device Tree (mandated for all AArch64 platforms)
- ARM generic timers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=buJB
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 support from Catalin Marinas:
"Linux support for the 64-bit ARM architecture (AArch64)
Features currently supported:
- 39-bit address space for user and kernel (each)
- 4KB and 64KB page configurations
- Compat (32-bit) user applications (ARMv7, EABI only)
- Flattened Device Tree (mandated for all AArch64 platforms)
- ARM generic timers"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (35 commits)
arm64: ptrace: remove obsolete ptrace request numbers from user headers
arm64: Do not set the SMP/nAMP processor bit
arm64: MAINTAINERS update
arm64: Build infrastructure
arm64: Miscellaneous header files
arm64: Generic timers support
arm64: Loadable modules
arm64: Miscellaneous library functions
arm64: Performance counters support
arm64: Add support for /proc/sys/debug/exception-trace
arm64: Debugging support
arm64: Floating point and SIMD
arm64: 32-bit (compat) applications support
arm64: User access library functions
arm64: Signal handling support
arm64: VDSO support
arm64: System calls handling
arm64: ELF definitions
arm64: SMP support
arm64: DMA mapping API
...
Pull x86/EFI changes from Ingo Molnar:
"EFI loader robustness enhancements plus smaller fixes"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Fix the ACPI BGRT driver for images located in EFI boot services memory
efi: Add a function to look up existing IO memory mappings
efi: Defer freeing boot services memory until after ACPI init
x86, EFI: Calculate the EFI framebuffer size instead of trusting the firmware
efifb: Skip DMI checks if the bootloader knows what it's doing
efi: initialize efi.runtime_version to make query_variable_info/update_capsule workable
efi: Build EFI stub with EFI-appropriate options
X86: Improve GOP detection in the EFI boot stub
Pull scheduler changes from Ingo Molnar:
"Continued quest to clean up and enhance the cputime code by Frederic
Weisbecker, in preparation for future tickless kernel features.
Other than that, smallish changes."
Fix up trivial conflicts due to additions next to each other in arch/{x86/}Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
cputime: Make finegrained irqtime accounting generally available
cputime: Gather time/stats accounting config options into a single menu
ia64: Reuse system and user vtime accounting functions on task switch
ia64: Consolidate user vtime accounting
vtime: Consolidate system/idle context detection
cputime: Use a proper subsystem naming for vtime related APIs
sched: cpu_power: enable ARCH_POWER
sched/nohz: Clean up select_nohz_load_balancer()
sched: Fix load avg vs. cpu-hotplug
sched: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix nohz_idle_balance()
sched: Remove useless code in yield_to()
sched: Add time unit suffix to sched sysctl knobs
sched/debug: Limit sd->*_idx range on sysctl
sched: Remove AFFINE_WAKEUPS feature flag
s390: Remove leftover account_tick_vtime() header
cputime: Consolidate vtime handling on context switch
sched: Move cputime code to its own file
cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING
tile: Remove SD_PREFER_LOCAL leftover
...
The ACPI BGRT driver accesses the BIOS logo image when it initializes.
However, ACPI 5.0 (which introduces the BGRT) recommends putting the
logo image in EFI boot services memory, so that the OS can reclaim that
memory. Production systems follow this recommendation, breaking the
ACPI BGRT driver.
Move the bulk of the BGRT code to run during a new EFI late
initialization phase, which occurs after switching EFI to virtual mode,
and after initializing ACPI, but before freeing boot services memory.
Copy the BIOS logo image to kernel memory at that point, and make it
accessible to the BGRT driver. Rework the existing ACPI BGRT driver to
act as a simple wrapper exposing that image (and the properties from the
BGRT) via sysfs.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/93ce9f823f1c1f3bb88bdd662cce08eee7a17f5d.1348876882.git.josh@joshtriplett.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Provide a config option that enables the userspace
RCU extended quiescent state on every CPUs by default.
This is for testing purpose.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Create a new config option under the RCU menu that put
CPUs under RCU extended quiescent state (as in dynticks
idle mode) when they run in userspace. This require
some contribution from architectures to hook into kernel
and userspace boundaries.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
There is no known reason for this option to be unavailable on other
archs than x86. They just need to call enable_sched_clock_irqtime()
if they have a sufficiently finegrained clock to make it working.
Move it to the general option and let the user choose between
it and pure tick based or virtual cputime accounting.
Note that virtual cputime accounting already performs a finegrained
irqtime accounting. CONFIG_IRQ_TIME_ACCOUNTING is a kind of middle ground
between tick and virtual based accounting. So CONFIG_IRQ_TIME_ACCOUNTING
and CONFIG_VIRT_CPU_ACCOUNTING are mutually exclusive choices.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This debloats a bit the general config menu and make these
config options easier to find.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
- General routine uid/gid conversion work
- When storing posix acls treat ACL_USER and ACL_GROUP separately
so I can call from_kuid or from_kgid as appropriate.
- When reading posix acls treat ACL_USER and ACL_GROUP separately
so I can call make_kuid or make_kgid as appropriate.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Tigran A. Aivazian" <tigran@aivazian.fsnet.co.uk>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Use kuid's in the IMA rules.
When reporting the current uid in audit logs use from_kuid
to get a usable value.
Cc: Mimi Zohar <zohar@us.ibm.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: John Johansen <john.johansen@canonical.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Note sysctl_hugetlb_shm_group can only be written in the root user
in the initial user namespace, so we can assume sysctl_hugetlb_shm_group
is in the initial user namespace.
Cc: William Irwin <wli@holomorphy.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that the type changes are done, here is the final set of
changes to make the quota code work when user namespaces are enabled.
Small cleanups and fixes to make the code build when user namespaces
are enabled.
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Modify quota_send_warning to take struct kqid instead a type and
identifier pair.
When sending netlink broadcasts always convert uids and quota
identifiers into the intial user namespace. There is as yet no way to
send a netlink broadcast message with different contents to receivers
in different namespaces, so for the time being just map all of the
identifiers into the initial user namespace which preserves the
current behavior.
Change the callers of quota_send_warning in gfs2, xfs and dquot
to generate a struct kqid to pass to quota send warning. When
all of the user namespaces convesions are complete a struct kqid
values will be availbe without need for conversion, but a conversion
is needed now to avoid needing to convert everything at once.
Cc: Ben Myers <bpm@sgi.com>
Cc: Alex Elder <elder@kernel.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Update the quotactl user space interface to successfull compile with
user namespaces support enabled and to hand off quota identifiers to
lower layers of the kernel in struct kqid instead of type and qid
pairs.
The quota on function is not converted because while it takes a quota
type and an id. The id is the on disk quota format to use, which
is something completely different.
The signature of two struct quotactl_ops methods were changed to take
struct kqid argumetns get_dqblk and set_dqblk.
The dquot, xfs, and ocfs2 implementations of get_dqblk and set_dqblk
are minimally changed so that the code continues to work with
the change in parameter type.
This is the first in a series of changes to always store quota
identifiers in the kernel in struct kqid and only use raw type and qid
values when interacting with on disk structures or userspace. Always
using struct kqid internally makes it hard to miss places that need
conversion to or from the kernel internal values.
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Ben Myers <bpm@sgi.com>
Cc: Alex Elder <elder@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Convert ext2, ext3, and ext4 to fully support the posix acl changes,
using e_uid e_gid instead e_id.
Enabled building with posix acls enabled, all filesystems supporting
user namespaces, now also support posix acls when user namespaces are enabled.
Cc: Theodore Tso <tytso@mit.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- When tracing capture the kuid.
- When displaying the data to user space convert the kuid into the
user namespace of the process that opened the report file.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
BSD process accounting conveniently passes the file the accounting
records will be written into to do_acct_process. The file credentials
captured the user namespace of the opener of the file. Use the file
credentials to format the uid and the gid of the current process into
the user namespace of the user that started the bsd process
accounting.
Cc: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Explicitly limit exit task stat broadcast to the initial user and
pid namespaces, as it is already limited to the initial network
namespace.
- For broadcast task stats explicitly generate all of the idenitiers
in terms of the initial user namespace and the initial pid
namespace.
- For request stats report them in terms of the current user namespace
and the current pid namespace. Netlink messages are delivered
syncrhonously to the kernel allowing us to get the user namespace
and the pid namespace from the current task.
- Pass the namespaces for representing pids and uids and gids
into bacct_add_task.
Cc: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Explicitly format uids gids in audit messges in the initial user
namespace. This is safe because auditd is restrected to be in
the initial user namespace.
- Convert audit_sig_uid into a kuid_t.
- Enable building the audit code and user namespaces at the same time.
The net result is that the audit subsystem now uses kuid_t and kgid_t whenever
possible making it almost impossible to confuse a raw uid_t with a kuid_t
preventing bugs.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This patch adds Makefile and Kconfig files required for building an
AArch64 kernel.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
In net/dns_resolver/dns_key.c and net/rxrpc/ar-key.c make them
work with user namespaces enabled where key_alloc takes kuids and kgids.
Pass GLOBAL_ROOT_UID and GLOBAL_ROOT_GID instead of bare 0's.
Cc: Sage Weil <sage@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: linux-afs@lists.infradead.org
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Replace key_user ->user_ns equality checks with kuid_has_mapping checks.
- Use from_kuid to generate key descriptions
- Use kuid_t and kgid_t and the associated helpers instead of uid_t and gid_t
- Avoid potential problems with file descriptor passing by displaying
keys in the user namespace of the opener of key status proc files.
Cc: linux-security-module@vger.kernel.org
Cc: keyrings@linux-nfs.org
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Blink Blink this had not been converted to use struct pid ages ago?
- On drm open capture the openers kuid and struct pid.
- On drm close release the kuid and struct pid
- When reporting the uid and pid convert the kuid and struct pid
into values in the appropriate namespace.
Cc: dri-devel@lists.freedesktop.org
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Store the ipc owner and creator with a kuid
- Store the ipc group and the crators group with a kgid.
- Add error handling to ipc_update_perms, allowing it to
fail if the uids and gids can not be converted to kuids
or kgids.
- Modify the proc files to display the ipc creator and
owner in the user namespace of the opener of the proc file.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Only allow asking for events from the initial user and pid namespace,
where we generate the events in.
- Convert kuids and kgids into the initial user namespace to report
them via the process event connector.
Cc: David Miller <davem@davemloft.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
CONFIG_HOTPLUG is a very old option, back when we had static systems and it was
odd that any type of device would be removed or added after the system had
started up. It is quite hard to disable it these days, and even if you do, it
only saves you about 200 bytes. However, if it is disabled, lots of bugs show
up because it is almost never tested if the option is disabled.
This is a step to eventually just remove the option entirely, which will clean
up all of the devinit* variable and function pointer options, that everyone
(myself include) ends up getting wrong eventually, causing real problems when
memory segments are removed yet we don't expect them to be.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Enable building of pf_key sockets and user namespace support at the
same time. This combination builds successfully so there is no reason
to forbid it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
S390, ia64 and powerpc all define their own version
of CONFIG_VIRT_CPU_ACCOUNTING. Generalize the config
and its description to a single place to avoid
duplication.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Maxim Krasnyansky <maxk@qualcomm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Only allow adding matches from the initial user namespace
- Add the appropriate conversion functions to handle matches
against sockets in other user namespaces.
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
xt_recent creates a bunch of proc files and initializes their uid
and gids to the values of ip_list_uid and ip_list_gid. When
initialize those proc files convert those values to kuids so they
can continue to reside on the /proc inode.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jan Engelhardt <jengelh@medozas.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
xt_LOG always writes messages via sb_add via printk. Therefore when
xt_LOG logs the uid and gid of a socket a packet came from the
values should be converted to be in the initial user namespace.
Thus making xt_LOG as user namespace safe as possible.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The flow classifier can use uids and gids of the sockets that
are transmitting packets and do insert those uids and gids
into the packet classification calcuation. I don't fully
understand the details but it appears that we can depend
on specific uids and gids when making traffic classification
decisions.
To work with user namespaces enabled map from kuids and kgids
into uids and gids in the initial user namespace giving raw
integer values the code can play with and depend on.
To avoid issues of userspace depending on uids and gids in
packet classifiers installed from other user namespaces
and getting confused deny all packet classifiers that
use uids or gids that are not comming from a netlink socket
in the initial user namespace.
Cc: Patrick McHardy <kaber@trash.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
At logging instance creation capture the peer netlink socket's user
namespace. Use the captured peer user namespace when reporting socket
uids to the peer.
The peer socket's user namespace is guaranateed to be valid until the user
closes the netlink socket. nfnetlink_log removes instances during the final
close of a socket. __build_packet_message does not get called after an
instance is destroyed. Therefore it is safe to let the peer netlink socket
take care of the user namespace reference counting for us.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Compute the user namespace of the socket that we are replying to
and translate the kuids of reported sockets into that user namespace.
Cc: Andrew Vagin <avagin@openvz.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Correct a long standing omission and use struct pid in the owner
field of struct ip6_flowlabel when the share type is IPV6_FL_S_PROCESS.
This guarantees we don't have issues when pid wraparound occurs.
Use a kuid_t in the owner field of struct ip6_flowlabel when the
share type is IPV6_FL_S_USER to add user namespace support.
In /proc/net/ip6_flowlabel capture the current pid namespace when
opening the file and release the pid namespace when the file is
closed ensuring we print the pid owner value that is meaning to
the reader of the file. Similarly use from_kuid_munged to print
uid values that are meaningful to the reader of the file.
This requires exporting pid_nr_ns so that ipv6 can continue to built
as a module. Yoiks what silliness
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Store sysctl_ping_group_range as a paire of kgid_t values
instead of a pair of gid_t values.
- Move the kgid conversion work from ping_init_sock into ipv4_ping_group_range
- For invalid cases reset to the default disabled state.
With the kgid_t conversion made part of the original value sanitation
from userspace understand how the code will react becomes clearer
and it becomes possible to set the sysctl ping group range from
something other than the initial user namespace.
Cc: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that the networking core is user namespace safe allow
networking and user namespaces to be built at the same time.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The user namespace code has an explicit "depends on USB_DEVICEFS = n"
dependency to prevent building code that is not yet user namespace safe. With
the removal of usbfs from the kernel it is now impossible to satisfy the
USB_DEFICEFS = n dependency and thus it is impossible to enable user
namespace support in 3.5-rc1. So remove the now useless depedency.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
When hotadd_new_pgdat() is called to create new pgdat for a new node, a
fallback zonelist should be created for the new node. There's code to try
to achieve that in hotadd_new_pgdat() as below:
/*
* The node we allocated has no zone fallback lists. For avoiding
* to access not-initialized zonelist, build here.
*/
mutex_lock(&zonelists_mutex);
build_all_zonelists(pgdat, NULL);
mutex_unlock(&zonelists_mutex);
But it doesn't work as expected. When hotadd_new_pgdat() is called, the
new node is still in offline state because node_set_online(nid) hasn't
been called yet. And build_all_zonelists() only builds zonelists for
online nodes as:
for_each_online_node(nid) {
pg_data_t *pgdat = NODE_DATA(nid);
build_zonelists(pgdat);
build_zonelist_cache(pgdat);
}
Though we hope to create zonelist for the new pgdat, but it doesn't. So
add a new parameter "pgdat" the build_all_zonelists() to build pgdat for
the new pgdat too.
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Keping Chen <chenkeping@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement a new controller that allows us to control HugeTLB allocations.
The extension allows to limit the HugeTLB usage per control group and
enforces the controller limit during page fault. Since HugeTLB doesn't
support page reclaim, enforcing the limit at page fault time implies that,
the application will get SIGBUS signal if it tries to access HugeTLB pages
beyond its limit. This requires the application to know beforehand how
much HugeTLB pages it would require for its use.
The charge/uncharge calls will be added to HugeTLB code in later patch.
Support for cgroup removal will be added in later patches.
[akpm@linux-foundation.org: s/CONFIG_CGROUP_HUGETLB_RES_CTLR/CONFIG_MEMCG_HUGETLB/g]
[akpm@linux-foundation.org: s/CONFIG_MEMCG_HUGETLB/CONFIG_CGROUP_HUGETLB/g]
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM updates from Russell King:
"First ARM push of this merge window, post me coming back from holiday.
This is what has been in linux-next for the last few weeks. Not much
to say which isn't described by the commit summaries."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (32 commits)
ARM: 7463/1: topology: Update cpu_power according to DT information
ARM: 7462/1: topology: factorize the update of sibling masks
ARM: 7461/1: topology: Add arch_scale_freq_power function
ARM: 7456/1: ptrace: provide separate functions for tracing syscall {entry,exit}
ARM: 7455/1: audit: move syscall auditing until after ptrace SIGTRAP handling
ARM: 7454/1: entry: don't bother with syscall tracing on ret_from_fork path
ARM: 7453/1: audit: only allow syscall auditing for pure EABI userspace
ARM: 7452/1: delay: allow timer-based delay implementation to be selected
ARM: 7451/1: arch timer: implement read_current_timer and get_cycles
ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for little-endian ARMv6+ CPUs
ARM: 7449/1: use generic strnlen_user and strncpy_from_user functions
ARM: 7448/1: perf: remove arm_perf_pmu_ids global enumeration
ARM: 7447/1: rwlocks: remove unused branch labels from trylock routines
ARM: 7446/1: spinlock: use ticket algorithm for ARMv6+ locking implementation
ARM: 7445/1: mm: update CONTEXTIDR register to contain PID of current process
ARM: 7444/1: kernel: add arch-timer C3STOP feature
ARM: 7460/1: remove asm/locks.h
ARM: 7439/1: head.S: simplify initial page table mapping
ARM: 7437/1: zImage: Allow DTB command line concatenation with ATAG_CMDLINE
ARM: 7436/1: Do not map the vectors page as write-through on UP systems
...
main.c has initcall_level_names[] for parse_args to print in debug messages,
add comments to keep them in sync with initcalls defined in init.h.
Also add "loadable" into comment re not using *_initcall macros in
modules, to disambiguate from kernel/params.c and other builtins.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pul x86/efi changes from Ingo Molnar:
"This tree adds an EFI bootloader handover protocol, which, once
supported on the bootloader side, will make bootup faster and might
result in simpler bootloaders.
The other change activates the EFI wall clock time accessors on x86-64
as well, instead of the legacy RTC readout."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Handover Protocol
x86-64/efi: Use EFI to deal with platform wall clock
... and schedule_work() for interrupt/kernel_thread callers
(and yes, now it *is* OK to call from interrupt).
We are guaranteed that __fput() will be done before we return
to userland (or exit). Note that for fput() from a kernel
thread we get an async behaviour; it's almost always OK, but
sometimes you might need to have __fput() completed before
you do anything else. There are two mechanisms for that -
a general barrier (flush_delayed_fput()) and explicit
__fput_sync(). Both should be used with care (as was the
case for fput() from kernel threads all along). See comments
in fs/file_table.c for details.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The audit tools support only EABI userspace and, since there are no
AUDIT_ARCH_* defines for the ARM OABI, it makes sense to allow syscall
auditing on ARM only for EABI at the moment.
Cc: Eric Paris <eparis@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
9fb48c744b ("params: add 3rd arg to option handler callback
signature") added similar lines to dmesg:
initlevel:0=early, 4 registered initcalls
initlevel:1=core, 31 registered initcalls
initlevel:2=postcore, 11 registered initcalls
initlevel:3=arch, 7 registered initcalls
initlevel:4=subsys, 40 registered initcalls
initlevel:5=fs, 30 registered initcalls
initlevel:6=device, 250 registered initcalls
initlevel:7=late, 35 registered initcalls
but they don't contain any info for the general user staring at dmesg.
I'm very doubtful the count of initcalls registered per level helps
anyone so drop that output completely.
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FBFBF5F020000780008637F@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge misc patches from Andrew Morton:
- the "misc" tree - stuff from all over the map
- checkpatch updates
- fatfs
- kmod changes
- procfs
- cpumask
- UML
- kexec
- mqueue
- rapidio
- pidns
- some checkpoint-restore feature work. Reluctantly. Most of it
delayed a release. I'm still rather worried that we don't have a
clear roadmap to completion for this work.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (78 patches)
kconfig: update compression algorithm info
c/r: prctl: add ability to set new mm_struct::exe_file
c/r: prctl: extend PR_SET_MM to set up more mm_struct entries
c/r: procfs: add arg_start/end, env_start/end and exit_code members to /proc/$pid/stat
syscalls, x86: add __NR_kcmp syscall
fs, proc: introduce /proc/<pid>/task/<tid>/children entry
sysctl: make kernel.ns_last_pid control dependent on CHECKPOINT_RESTORE
aio/vfs: cleanup of rw_copy_check_uvector() and compat_rw_copy_check_uvector()
eventfd: change int to __u64 in eventfd_signal()
fs/nls: add Apple NLS
pidns: make killed children autoreap
pidns: use task_active_pid_ns in do_notify_parent
rapidio/tsi721: add DMA engine support
rapidio: add DMA engine support for RIO data transfers
ipc/mqueue: add rbtree node caching support
tools/selftests: add mq_perf_tests
ipc/mqueue: strengthen checks on mqueue creation
ipc/mqueue: correct mq_attr_ok test
ipc/mqueue: improve performance of send/recv
selftests: add mq_open_tests
...
There have been new compression algorithms added without updating nearby
relevant descriptive text that refers to (a) the number of compression
algorithms and (b) the most recent one. Fix these inconsistencies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: <qasdfgtyuiop@gmail.com>
Cc: Lasse Collin <lasse.collin@tukaani.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Alain Knaff <alain@knaff.lu>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The init/mount.o source files produce a number of sparse warnings of the
type:
warning: incorrect type in argument 1 (different address spaces)
expected char [noderef] <asn:1>*dev_name
got char *name
This is due to the syscalls expecting some of the arguments to be user
pointers but they are being passed as kernel pointers. This is harmless
but adds a lot of noise to a sparse build.
To limit the noise just disable the sparse checking in the relevant source
files, but still display a warning so that the user knows this has been
done.
Since the sparse checking has been disabled we can also remove the __user
__force casts that are scattered thru the source.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge block/IO core bits from Jens Axboe:
"This is a bit bigger on the core side than usual, but that is purely
because we decided to hold off on parts of Tejun's submission on 3.4
to give it a bit more time to simmer. As a consequence, it's seen a
long cycle in for-next.
It contains:
- Bug fix from Dan, wrong locking type.
- Relax splice gifting restriction from Eric.
- A ton of updates from Tejun, primarily for blkcg. This improves
the code a lot, making the API nicer and cleaner, and also includes
fixes for how we handle and tie policies and re-activate on
switches. The changes also include generic bug fixes.
- A simple fix from Vivek, along with a fix for doing proper delayed
allocation of the blkcg stats."
Fix up annoying conflict just due to different merge resolution in
Documentation/feature-removal-schedule.txt
* 'for-3.5/core' of git://git.kernel.dk/linux-block: (92 commits)
blkcg: tg_stats_alloc_lock is an irq lock
vmsplice: relax alignement requirements for SPLICE_F_GIFT
blkcg: use radix tree to index blkgs from blkcg
blkcg: fix blkcg->css ref leak in __blkg_lookup_create()
block: fix elvpriv allocation failure handling
block: collapse blk_alloc_request() into get_request()
blkcg: collapse blkcg_policy_ops into blkcg_policy
blkcg: embed struct blkg_policy_data in policy specific data
blkcg: mass rename of blkcg API
blkcg: style cleanups for blk-cgroup.h
blkcg: remove blkio_group->path[]
blkcg: blkg_rwstat_read() was missing inline
blkcg: shoot down blkgs if all policies are deactivated
blkcg: drop stuff unused after per-queue policy activation update
blkcg: implement per-queue policy activation
blkcg: add request_queue->root_blkg
blkcg: make request_queue bypassing on allocation
blkcg: make sure blkg_lookup() returns %NULL if @q is bypassing
blkcg: make blkg_conf_prep() take @pol and return with queue lock held
blkcg: remove static policy ID enums
...
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
Pull exception table generation updates from Ingo Molnar:
"The biggest change here is to allow the build-time sorting of the
exception table, to speed up booting. This is achieved by the
architecture enabling BUILDTIME_EXTABLE_SORT. This option is enabled
for x86 and MIPS currently.
On x86 a number of fixes and changes were needed to allow build-time
sorting of the exception table, in particular a relocation invariant
exception table format was needed. This required the abstracting out
of exception table protocol and the removal of 20 years of accumulated
assumptions about the x86 exception table format.
While at it, this tree also cleans up various other aspects of
exception handling, such as early(er) exception handling for
rdmsr_safe() et al.
All in one, as the result of these changes the x86 exception code is
now pretty nice and modern. As an added bonus any regressions in this
code will be early and violent crashes, so if you see any of those,
you'll know whom to blame!"
Fix up trivial conflicts in arch/{mips,x86}/Kconfig files due to nearby
modifications of other core architecture options.
* 'x86-extable-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
Revert "x86, extable: Disable presorted exception table for now"
scripts/sortextable: Handle relative entries, and other cleanups
x86, extable: Switch to relative exception table entries
x86, extable: Disable presorted exception table for now
x86, extable: Add _ASM_EXTABLE_EX() macro
x86, extable: Remove open-coded exception table entries in arch/x86/ia32/ia32entry.S
x86, extable: Remove open-coded exception table entries in arch/x86/include/asm/xsave.h
x86, extable: Remove open-coded exception table entries in arch/x86/include/asm/kvm_host.h
x86, extable: Remove the now-unused __ASM_EX_SEC macros
x86, extable: Remove open-coded exception table entries in arch/x86/xen/xen-asm_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/um/checksum_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/usercopy_32.c
x86, extable: Remove open-coded exception table entries in arch/x86/lib/putuser.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/getuser.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/csum-copy_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/copy_user_nocache_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/copy_user_64.S
x86, extable: Remove open-coded exception table entries in arch/x86/lib/checksum_32.S
x86, extable: Remove open-coded exception table entries in arch/x86/kernel/test_rodata.c
x86, extable: Remove open-coded exception table entries in arch/x86/kernel/entry_64.S
...
Pull perf changes from Ingo Molnar:
"Lots of changes:
- (much) improved assembly annotation support in perf report, with
jump visualization, searching, navigation, visual output
improvements and more.
- kernel support for AMD IBS PMU hardware features. Notably 'perf
record -e cycles:p' and 'perf top -e cycles:p' should work without
skid now, like PEBS does on the Intel side, because it takes
advantage of IBS transparently.
- the libtracevents library: it is the first step towards unifying
tracing tooling and perf, and it also gives a tracing library for
external tools like powertop to rely on.
- infrastructure: various improvements and refactoring of the UI
modules and related code
- infrastructure: cleanup and simplification of the profiling
targets code (--uid, --pid, --tid, --cpu, --all-cpus, etc.)
- tons of robustness fixes all around
- various ftrace updates: speedups, cleanups, robustness
improvements.
- typing 'make' in tools/ will now give you a menu of projects to
build and a short help text to explain what each does.
- ... and lots of other changes I forgot to list.
The perf record make bzImage + perf report regression you reported
should be fixed."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (166 commits)
tracing: Remove kernel_lock annotations
tracing: Fix initial buffer_size_kb state
ring-buffer: Merge separate resize loops
perf evsel: Create events initially disabled -- again
perf tools: Split term type into value type and term type
perf hists: Fix callchain ip printf format
perf target: Add uses_mmap field
ftrace: Remove selecting FRAME_POINTER with FUNCTION_TRACER
ftrace/x86: Have x86 ftrace use the ftrace_modify_all_code()
ftrace: Make ftrace_modify_all_code() global for archs to use
ftrace: Return record ip addr for ftrace_location()
ftrace: Consolidate ftrace_location() and ftrace_text_reserved()
ftrace: Speed up search by skipping pages by address
ftrace: Remove extra helper functions
ftrace: Sort all function addresses, not just per page
tracing: change CPU ring buffer state from tracing_cpumask
tracing: Check return value of tracing_dentry_percpu()
ring-buffer: Reset head page before running self test
ring-buffer: Add integrity check at end of iter read
ring-buffer: Make addition of pages in ring buffer atomic
...
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Pull RCU changes from Ingo Molnar:
"This is the v3.5 RCU tree from Paul E. McKenney:
1) A set of improvements and fixes to the RCU_FAST_NO_HZ feature (with
more on the way for 3.6). Posted to LKML:
https://lkml.org/lkml/2012/4/23/324 (commits 1-3 and 5),
https://lkml.org/lkml/2012/4/16/611 (commit 4),
https://lkml.org/lkml/2012/4/30/390 (commit 6), and
https://lkml.org/lkml/2012/5/4/410 (commit 7, combined with
the other commits for the convenience of the tester).
2) Changes to make rcu_barrier() avoid disrupting execution of CPUs
that have no RCU callbacks. Posted to LKML:
https://lkml.org/lkml/2012/4/23/322.
3) A couple of commits that improve the efficiency of the interaction
between preemptible RCU and the scheduler, these two being all that
survived an abortive attempt to allow preemptible RCU's
__rcu_read_lock() to be inlined. The full set was posted to LKML at
https://lkml.org/lkml/2012/4/14/143, and the first and third patches
of that set remain.
4) Lai Jiangshan's algorithmic implementation of SRCU, which includes
call_srcu() and srcu_barrier(). A major feature of this new
implementation is that synchronize_srcu() no longer disturbs the
execution of other CPUs. This work is based on earlier
implementations by Peter Zijlstra and Paul E. McKenney. Posted to
LKML: https://lkml.org/lkml/2012/2/22/82.
5) A number of miscellaneous bug fixes and improvements which were
posted to LKML at: https://lkml.org/lkml/2012/4/23/353 with
subsequent updates posted to LKML."
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
rcu: Make rcu_barrier() less disruptive
rcu: Explicitly initialize RCU_FAST_NO_HZ per-CPU variables
rcu: Make RCU_FAST_NO_HZ handle timer migration
rcu: Update RCU maintainership
rcu: Make exit_rcu() more precise and consolidate
rcu: Move PREEMPT_RCU preemption to switch_to() invocation
rcu: Ensure that RCU_FAST_NO_HZ timers expire on correct CPU
rcu: Add rcutorture test for call_srcu()
rcu: Implement per-domain single-threaded call_srcu() state machine
rcu: Use single value to handle expedited SRCU grace periods
rcu: Improve srcu_readers_active_idx()'s cache locality
rcu: Remove unused srcu_barrier()
rcu: Implement a variant of Peter's SRCU algorithm
rcu: Improve SRCU's wait_idx() comments
rcu: Flip ->completed only once per SRCU grace period
rcu: Increment upper bit only for srcu_read_lock()
rcu: Remove fast check path from __synchronize_srcu()
rcu: Direct algorithmic SRCU implementation
rcu: Introduce rcutorture testing for rcu_barrier()
timer: Fix mod_timer_pinned() header comment
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
During early boot, when the scheduler hasn't really been fully set up,
we really can't do blocking allocations because with certain (dubious)
configurations the "might_resched()" calls can actually result in
scheduling events.
We could just make such users always use GFP_ATOMIC, but quite often the
code that does the allocation isn't really aware of the fact that the
scheduler isn't up yet, and forcing that kind of random knowledge on the
initialization code is just annoying and not good for anybody.
And we actually have a the 'gfp_allowed_mask' exactly for this reason:
it's just that the kernel init sequence happens to set it to allow
blocking allocations much too early.
So move the 'gfp_allowed_mask' initialization from 'start_kernel()'
(which is some of the earliest init code, and runs with preemption
disabled for good reasons) into 'kernel_init()'. kernel_init() is run
in the newly created thread that will become the 'init' process, as
opposed to the early startup code that runs within the context of what
will be the first idle thread.
So by the time we reach 'kernel_init()', we know that the scheduler must
be at least limping along, because we've already scheduled from the idle
thread into the init thread.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge reason: We are going to queue up a dependent patch:
"perf tools: Move parse event automated tests to separated object"
That depends on:
commit e7c72d8
perf tools: Add 'G' and 'H' modifiers to event parsing
Conflicts:
tools/perf/builtin-stat.c
Conflicted with the recent 'perf_target' patches when checking the
result of perf_evsel open routines to see if a retry is needed to cope
with older kernels where the exclude guest/host perf_event_attr bits
were not used.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a new internal Kconfig option UIDGID_CONVERTED that is true when the selected
Kconfig options have been converted to be user namespace safe, and guard
USER_NS and guard the UIDGID_STRICT_TYPE_CHECK options with it.
This keeps innocent kernel users from having the choice to enable
the user namespace in the cases where it is known not to work.
Most of the rest of the conversions are simple and straight forward but
their sheer number means it is good not to count on having them all done
and reviwed before thinking of merging this code.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Pull the v3.5 RCU tree from Paul E. McKenney:
1) A set of improvements and fixes to the RCU_FAST_NO_HZ feature
(with more on the way for 3.6). Posted to LKML:
https://lkml.org/lkml/2012/4/23/324 (commits 1-3 and 5),
https://lkml.org/lkml/2012/4/16/611 (commit 4),
https://lkml.org/lkml/2012/4/30/390 (commit 6), and
https://lkml.org/lkml/2012/5/4/410 (commit 7, combined with
the other commits for the convenience of the tester).
2) Changes to make rcu_barrier() avoid disrupting execution of CPUs
that have no RCU callbacks. Posted to LKML:
https://lkml.org/lkml/2012/4/23/322.
3) A couple of commits that improve the efficiency of the interaction
between preemptible RCU and the scheduler, these two being all
that survived an abortive attempt to allow preemptible RCU's
__rcu_read_lock() to be inlined. The full set was posted to
LKML at https://lkml.org/lkml/2012/4/14/143, and the first and
third patches of that set remain.
4) Lai Jiangshan's algorithmic implementation of SRCU, which includes
call_srcu() and srcu_barrier(). A major feature of this new
implementation is that synchronize_srcu() no longer disturbs
the execution of other CPUs. This work is based on earlier
implementations by Peter Zijlstra and Paul E. McKenney. Posted to
LKML: https://lkml.org/lkml/2012/2/22/82.
5) A number of miscellaneous bug fixes and improvements which were
posted to LKML at: https://lkml.org/lkml/2012/4/23/353 with
subsequent updates posted to LKML.
Signed-off-by: Ingo Molnar <mingo@kernel.org>