commit 686f85d71d upstream.
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 772f66421d upstream.
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27e0c31c5f upstream.
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f4b7e6a2b upstream.
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89ba879e95 upstream.
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94b1663495 upstream.
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaabfd19b2 upstream.
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e311820f6 upstream.
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427db97df1 upstream.
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3885f5761 upstream.
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fedabf5a7 upstream.
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 865ad2f220 upstream.
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2378ab0f upstream.
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9f726c942 upstream.
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63963d0f9d upstream.
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d829229e35 upstream.
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831ac12356b695ff054bef641b9e99593:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 205608749e upstream.
Since v5.4-rc1 was released, iwlwifi started throwing errors when scan
commands were sent to the firmware with certain devices (depending on
the OTP burned in the device, which contains the list of available
channels). For instance:
iwlwifi 0000:00:14.3: FW error in SYNC CMD SCAN_CFG_CMD
This bug was reported in the ArchLinux bug tracker:
https://bugs.archlinux.org/task/64703
And also in a specific case in bugzilla, when the lar_disabled option
was set: https://bugzilla.kernel.org/show_bug.cgi?id=205193
Revert the commit that introduced this error, by using the number of
channels from the OTP instead of the number of channels that is
specified in the FW TLV that tells us how many channels it supports.
This reverts commit 06eb547c4a.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Mehmet Akif Tasova <makiftasova@gmail.com>
[ Luca: reworded the commit message a bit. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 342508c1c7 upstream.
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e92899791 upstream.
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec49742 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffbd9ca94e upstream.
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0702a4bd4 upstream.
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e401a1848b upstream.
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commmit b850a82114 upstream.
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 505a7f5478 upstream
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c41 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b8a7ecb7 upstream.
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c280240 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c80794323e ]
Commit 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 971de2e572 ]
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78f7a7566f ]
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6bce2137f ]
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1efba987c4 ]
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce896476c6 ]
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3546d8f1bb =
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 148965df1a ]
Before commit 7587935cfa ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ace17d568 ]
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21 ("slip: Fix deadlock in write_wakeup")
Fixes: a8e83b1753 ("slcan: Port write_wakeup deadlock fix from slip")
Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tyler Hall <tylerwhall@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 80df01f4dc ]
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8 ("mt76usb: use usb_dev private data")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-By: Zero_Chaos <sidhayn@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb34e98baf ]
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1f7c2cabf ]
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9f540ca7 ]
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a4f4f3a89 ]
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c70fd3182c ]
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9496f3ecf ]
bpf_xdp_adjust_head() can change the frame boundaries. Account for the
potential shift properly by calculating the new offset before
syncing the buffer to the device for XDP_TX
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f4268729eb upstream.
Disable efuse if the efuse is enabled when we failed to setup the efuse
information, otherwise the hardware will not turn off.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3594559f4 upstream.
When downloading the reserved page, the first page always contains
a beacon for the firmware to reference. For non-beaconing modes such
as station mode, also put a blank skb with length=1.
And for the beaconing modes, driver will get a real beacon with a
length approximate to the page size. But as the beacon is always put
at the first page, it does not need a tx_desc, because the TX path
will generate one when TXing the reserved page to the hardware. So we
could allocate a buffer with a size smaller than the reserved page,
when using memcpy() to copy the content of reserved page to the buffer,
the over-sized reserved page will violate the kernel memory.
To fix it, add the tx_desc before memcpy() the reserved packets to
the buffer, then we can get SKBs with correct length when counting
the pages in total. And for page 0, count the extra tx_desc_sz that
the TX path will generate. This way, the first beacon that allocated
without tx_desc can be counted with the extra tx_desc_sz to get
actual pages it requires.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 949375de94 upstream.
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e14f76f8 upstream.
Fix bbp ready check in mt7601u_wait_bbp_ready. The issue is reported by
coverity with the following error:
Logical vs. bitwise operator
The expression's value does not depend on the operands; inadvertent use
of the wrong operator is a likely logic error.
Addresses-Coverity-ID: 1309441 ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cb16d2cc upstream.
Even if they are not currently used fix BK/BE endpoint definition order.
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fea7fda7f5 upstream.
Commit 0fc9ae1076 ("net: phy: broadcom: add support for
BCM54210E") added support for BCM54210E but also unconditionally cleared
the RXC to RXD skew and the TXD to TXC skew, thus only making
PHY_INTERFACE_MODE_RGMII a possible configuration. Use
bcm54xx_config_clock_delay() which correctly sets the registers
depending on the 4 possible PHY interface values that exist for RGMII.
Fixes: 0fc9ae1076 ("net: phy: broadcom: add support for BCM54210E")
Reported-by: Manasa Mudireddy <manasa.mudireddy@broadcom.com>
Reported-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb252c3a24 upstream.
It could be neigh update flow took a refcount on peer flow so
sometimes we cannot release peer flow even if parent flow is
being freed now.
Fixes: 5a7e5bcb66 ("net/mlx5e: Extend tc flow struct with reference counter")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a0696e85 upstream.
The level of cckpd is from 0 to 4, and it is the index of
array pd_lvl[] and cs_lvl[]. However, the length of both arrays
are 4, which is smaller than the possible maximum input index.
Enumerate cck level to make sure the max level will not be wrong
if new level is added in future.
Fixes: 479c4ee931 ("rtw88: add dynamic cck pd mechanism")
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a50d45450 upstream.
The "priv->hw_type" is an enum and in this context GCC will treat it
as an unsigned int so the error handling will never trigger.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bd754c47d upstream.
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e715d74504 upstream.
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d39b68e5a7 upstream.
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e1838200 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b9f932edc upstream.
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85005b82e5 upstream.
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca7609ff36 upstream.
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2da51ce75d upstream.
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3249b1e442 upstream.
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27d4613334 ]
In i40e_setup_macvlans if i40e_setup_channel fails the allocated memory
for ch should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f1880cbe8 ]
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27afe0d34e ]
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a9ef19454 ]
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c4407046 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82d5d6a638 ]
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d061b2411d ]
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6fc7caa84e ]
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ceb3284c58 ]
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86f3f4cd53 ]
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ddf4203905 ]
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: c19b6d246a ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8d7408a4d ]
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86ffe920e6 ]
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49edd6a2c4 ]
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36c67349a1 ]
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1712b2fff8 ]
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b6958 ("macvlan: do not assume mac_header is set in macvlan_broadcast()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jurgen Van Ham <juvanham@gmail.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2f3a481c4 upstream.
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8605131747 upstream.
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb99ff9baa upstream.
When the single antenna diversity support was sent upstream, only some
definitions were sent, due to a bad revert.
Fix this by adding the actual code.
Fixes: 5952e0ec3f ("iwlwifi: mvm: add support for single antenna diversity")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 091c6e9c08 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison
of address of 'rtlpriv->regd' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (wiphy == NULL || &rtlpriv->regd == NULL)
~~~~~~~~~^~~~ ~~~~
1 warning generated.
The address of an array member is never NULL unless it is the first
struct member so remove the unnecessary check. This was addressed in
the staging version of the driver in commit f986978b32 ("Staging:
rtlwifi: remove unnecessary NULL check").
While we are here, fix the following checkpatch warning:
CHECK: Comparison to NULL could be written "!wiphy"
35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389:
+ if (wiphy == NULL)
Fixes: 0c8173385e ("rtl8192ce: Add new driver")
Link:https://github.com/ClangBuiltLinux/linux/issues/750
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee4cce9b9d upstream.
debugfs amsdu_len sets only the max_amsdu_len for ieee80211 station
so take it into consideration while getting max amsdu
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f170d44bc4 upstream.
The id pointer can be NULL in rsi_probe(). It is checked everywhere except
for the else branch in the idProduct condition. The patch adds NULL check
before the id dereference in the rsi_dbg() call.
Fixes: 54fdb318c1 ("rsi: add new device model for 9116")
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22d0d5ae7a upstream.
This patch changes the ath9k_pci_owl_loader to use the
same iowrite32 memory accessor that ath9k_pci is using
to communicate with the PCI(e) chip.
This will fix endian issues that came up during testing
with loaned AVM Fritz!Box 7360 (Lantiq MIPS SoCs + AR9287).
Fixes: 5a4f2040fd ("ath9k: add loader for AR92XX (and older) pci(e)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8d17e7d93 upstream.
In ath10k_usb_hif_tx_sg the allocated urb should be released if
usb_submit_urb fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2cdd07488 upstream.
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db8fd2cde9 upstream.
In mwifiex_pcie_alloc_cmdrsp_buf, a new skb is allocated which should be
released if mwifiex_map_pci_memory() fails. The release is added.
Fixes: fc33146090 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d94a4a837 upstream.
mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.
This fix addresses CVE-2019-14895.
Reported-by: huangwen <huangwenabc@gmail.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d77bd61a2 upstream.
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3069ce620d upstream.
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f361cd947 upstream.
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5660493c63 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df55c5586e ]
Whenever adding new member of rule object we attach it to 2 lists,
These 2 lists should be initialized first.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6412bb396a ]
Set hairpin table size to the corret size, based on the groups that
would be created in it. Groups are laid out on the table such that a
group occupies a range of entries in the table. This implies that the
group ranges should have correspondence to the table they are laid upon.
The patch cited below made group 1's size to grow hence causing
overflow of group range laid on the table.
Fixes: a795d8db2a ("net/mlx5e: Support RSS for IP-in-IP and IPv6 tunneled packets")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ce380ca47 ]
No need for an atomic refcounter for the STE and hashtables.
These are internal SW steering resources and they are always
under domain mutex.
This also fixes the following refcount error:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 9 PID: 3527 at lib/refcount.c:25 refcount_warn_saturate+0x81/0xe0
Call Trace:
dr_table_init_nic+0x10d/0x110 [mlx5_core]
mlx5dr_table_create+0xb4/0x230 [mlx5_core]
mlx5_cmd_dr_create_flow_table+0x39/0x120 [mlx5_core]
__mlx5_create_flow_table+0x221/0x5f0 [mlx5_core]
esw_create_offloads_fdb_tables+0x180/0x5a0 [mlx5_core]
...
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99cda45426 ]
In case a reporter exists, error message is logged only to the devlink
tracer. The devlink tracer is a visibility utility only, which user can
choose not to monitor.
After cited patch, 3rd party monitoring tools that tracks these error
message will no longer find them in dmesg, causing a regression.
With this patch, error messages are also logged into the dmesg.
Fixes: c50de4af1d ("net/mlx5e: Generalize tx reporter's functionality")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7a48b68ab ]
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6f3b62386 ]
Register devlink before interfaces are added.
This will allow interfaces to use devlink while initalizing. For example,
call mlx5_is_roce_enabled.
Fixes: aba25279c1 ("net/mlx5e: Add TX reporter support")
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d89091a493 ]
The only clk init function in this driver that register a clk is
fu540_c000_clk_init(), and thus we need to unregister the clk when this
driver is removed on that platform. Other init functions, for example
macb_clk_init(), don't register clks and therefore we shouldn't
unregister the clks when this driver is removed. Convert this
registration path to devm so it gets auto-unregistered when this driver
is removed and drop the clk_unregister() calls in driver remove (and
error paths) so that we don't erroneously remove a clk from the system
that isn't registered by this driver.
Otherwise we get strange crashes with a use-after-free when the
devm_clk_get() call in macb_clk_init() calls clk_put() on a clk pointer
that has become invalid because it is freed in clk_unregister().
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Yash Shah <yash.shah@sifive.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3971a535b8 ]
The following patch will change PRIO to replace a removed Qdisc with an
invisible FIFO, instead of NOOP. mlxsw will see this replacement due to the
graft message that is generated. But because FIFO does not issue its own
REPLACE message, when the graft operation takes place, the Qdisc that mlxsw
tracks under the indicated band is still the old one. The child
handle (0:0) therefore does not match, and mlxsw rejects the graft
operation, which leads to an extack message:
Warning: Offloading graft operation failed.
Fix by ignoring the invisible children in the PRIO graft handler. The
DESTROY message of the removed Qdisc is going to follow shortly and handle
the removal.
Fixes: 32dc5efc6c ("mlxsw: spectrum: qdiscs: prio: Handle graft command")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71130f2997 ]
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd2 ("VXLAN: Use IP Tunnels tunnel ENC encap API")
Fixes: 1400615d64 ("vxlan: allow setting ipv6 traffic class")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finn Thain