Dan Carpenter reports that we don't check the allocation here for
failure. Add a failure check and free any previously allocated
providers from the clk_provider_list.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=I0gO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 300000000
div_hpm rate: 300000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 300000000
div_pclk_dbg rate: 150000000
sclk_apll rate: 1200000000
sclk_apll_div_2 rate: 600000000
With use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 200000000
div_hpm rate: 200000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 240000000
div_pclk_dbg rate: 120000000
sclk_apll rate: 150000000
sclk_apll_div_2 rate: 75000000
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The debug_node field is only used when DEBUG_FS config is selected,
so declare it only if DEBUG_FS is selected.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sprinkled all through the platform clock drivers are code like this to
fill the clock parent array:
for (i = 0; i < num_parents; ++i)
parent_names[i] = of_clk_get_parent_name(np, i);
The of_clk_parent_fill() will do the same as the code above, and while
at it, return the number of parents as well since the logic of the
function is to the walk the clock node to look for the parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
[sboyd@codeaurora.org: Fixed kernel-doc]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk.c:2700:5: warning: symbol '__clk_get' was not declared. Should it be static?
drivers/clk/clk.c:2713:6: warning: symbol '__clk_put' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
To be used by clock implementations for switching to a new parent during
rate change.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We don't check to make sure the enable_lock is held across
enable/disable and we don't check if the prepare_lock is held
across prepare/unprepare. Add some asserts to catch any future
locking problems.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk_dump() will dump data about all clocks in JSON
format, but it misses a newline character at the
end of the JSON string. This patch adds that missing
newline character.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[sboyd@codeaurora.org: Squelch checkpatch with seq_puts()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Before commit 035a61c314 ("clk: Make clk API return per-user
struct clk instances") we acquired the enable_lock in
__clk_set_parent_{before,after}() by means of calling
clk_enable(). After commit 035a61c314 we use clk_core_enable()
in place of the clk_enable(), and clk_core_enable() doesn't
acquire the enable_lock. This opens up a race condition between
clk_set_parent() and clk_enable(). Fix it.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
key/value pairs in a JSON object must be separated by a comma.
After adding the properties "accuracy" and "phase" the JSON output
of /sys/kernel/debug/clk/clk_dump is invalid.
So add the missing commas to fix it.
Fixes: 5279fc402a ("clk: add clk accuracy retrieval support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
[sboyd@codeaurora.org: Added comment in function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The debugfs clk directory no longer expresses a clk tree. Update
the comments around that apporiately. Also drop comments about
prepare locks needing to be held as we have the proper
annotations with lockdep_assert_held().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the code around so that we don't need to declare function
prototypes at the start of the file. Simplify
clk_core_is_prepared() and clk_core_is_enabled() too to make the
diff easier to read.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This condition can't ever be true because this function is static
and it's always called with a non-NULL pointer.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We don't need to print error messages when allocations fail.
We'll get a nice backtrace in such situations anyway.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These functions are only used in one place. Let's squash them
into their respective callers to save some lines.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
[sboyd@codeaurora.org: Redo commit text, add NULL check in
clk_enable()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While introducing struct clk_core we tried to minimize the diff
by changing the type of 'clk' variables from struct clk to struct
clk_core without changing the names of the variables. Now that
the split is complete, the code is slightly confusing when it
mixes variables called 'clk' and variables called 'core' that are
of the same type struct clk_core. Let's be consistent and use
'core' everywhere we have a struct clk_core pointer and 'clk'
when we have a struct clk pointer.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
->determine_rate() and ->round_rate() can return the closest rate to the
requested one or an error code.
clk_calc_new_rates is assuming these functions can't return a negative
value, which leads to a undefined behavior when the clk implementation
returns such an error code.
Fix this by returning NULL in case ->determine_rate() or ->round_rate()
returned an error code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
of_clk_get_by_clkspec() has the same function signature as
of_clk_get_from_provider()
struct clk *of_clk_get_by_clkspec(struct of_phandle_args
*clkspec)
struct clk *of_clk_get_from_provider(struct of_phandle_args
*clkspec)
except of_clk_get_by_clkspec() checks to make sure clkspec is not
NULL. Let's remove of_clk_get_by_clkspec() and replace the
callers of it (clkconf.c) with of_clk_get_from_provider().
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The child_node member of struct clk is named the same as the
child_node member of struct clk_core. Let's rename the struct
clk's member to clks_node to avoid getting confused with the
child_node member of struct clk_core and to match the name of the
list head, clks.
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Alban Browaeys <alban.browaeys@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If a driver calls clk_set_parent(clk, parent) and parent is the
current parent of clk we shouldn't fail in any case.
Unfortunately if clk is a read-only mux we return -ENOSYS
because we think we can't change the parent, except for in this
special case where we don't actually need to change the parent at
all. Return 0 in such a situation.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
It's useful to have tracepoints around operations that change the
hardware state so that we can debug clock hardware performance
and operations. Four basic types of events are supported: on/off
events for enable, disable, prepare, unprepare that only record
an event and a clock name, rate changing events for
clk_set_{min_,max_}rate{_range}(), phase changing events for
clk_set_phase() and parent changing events for clk_set_parent().
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
If a clock's clk_ops doesn't have the set_phase op set we should
return an error from clk_set_phase(). This way clock consumers
know that when they tried to set a phase it didn't work, as
opposed to the current behavior where the return value is 0
meaning success.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add lockdep asserts for holding the prepare_lock to all functions
marking this as a requirement in description. Add this to private and
exported functions so all locking misuse could be detected during
debugging.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some drivers compare struct clk pointers as a means of knowing
if the two pointers reference the same clock hardware. This behavior is
dubious (drivers must not dereference struct clk), but did not cause any
regressions until the per-user struct clk patch was merged. Now the test
for matching clk's will always fail with per-user struct clk's.
clk_is_match is introduced to fix the regression and prevent drivers
from comparing the pointers manually.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[arnd@arndb.de: Fix COMMON_CLK=N && HAS_CLK=Y config]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[sboyd@codeaurora.org: const arguments to clk_is_match() and
remove unnecessary ternary operation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
We don't really need to recalculate the effective rate of a clock when a
per-user clock is removed, if the constraints of the later aren't
limiting the requested rate.
This was causing problems with clocks that never had a rate set before,
as rate_req would be zero. Though this could be considered a bug in the
implementation of those clocks, this should be checked somewhere else.
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clock passed as an argument to clk_mux_determine_rate_flags()
has the CLK_SET_RATE_PARENT flag set but it has no parent, then a
NULL pointer will tried to be dereferenced.
This shouldn't happen since setting that flag for a clock with no
parent is a bug but the core should be robust to handle that case.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Clock subsystem frequently performs duplication of strings located in
read-only memory section. Replacing kstrdup by kstrdup_const allows to
avoid such operations.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_clk_get_by_clkspec() returns a struct clk pointer but it
doesn't create a new handle for the consumers when we're using
the common clock framework. Instead it just returns whatever the
clk provider hands out. When the consumers go to call clk_put()
we get an Oops.
Unable to handle kernel paging request at virtual address 00200200
pgd = c0004000
[00200200] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc1-00104-ga251361a-dirty #992
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: ee00b000 ti: ee088000 task.ti: ee088000
PC is at __clk_put+0x24/0xd0
LR is at clk_prepare_lock+0xc/0xec
pc : [<c03eef38>] lr : [<c03ec1f4>] psr: 20000153
sp : ee089de8 ip : 00000000 fp : 00000000
r10: ee02f480 r9 : 00000001 r8 : 00000000
r7 : ee031cc0 r6 : ee089e08 r5 : 00000000 r4 : ee02f480
r3 : 00100100 r2 : 00200200 r1 : 0000091e r0 : 00000001
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 4000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee088238)
Stack: (0xee089de8 to 0xee08a000)
9de0: ee7c8f14 c03f0ec8 ee089e08 00000000 c0718dc8 00000001
9e00: 00000000 c04ee0f0 ee7e0844 00000001 00000181 c04edb58 ee2bd320 00000000
9e20: 00000000 c011dc5c ee16a1e0 00000000 00000000 c0718dc8 ee16a1e0 ee2bd1e0
9e40: c0641740 ee16a1e0 00000000 ee2bd320 c0718dc8 ee1d3e10 ee1d3e10 00000000
9e60: c0769a88 00000000 c0718dc8 00000000 00000000 c02c3124 c02c310c ee1d3e10
9e80: c07b4eec 00000000 c0769a88 c02c1d0c ee1d3e10 c0769a88 ee1d3e44 00000000
9ea0: c07091dc c02c1eb8 00000000 c0769a88 c02c1e2c c02c0544 ee005478 ee1676c0
9ec0: c0769a88 ee3a4e80 c0760ce8 c02c150c c0669b90 c0769a88 c0746cd8 c0769a88
9ee0: c0746cd8 ee2bc4c0 c0778c00 c02c24e0 00000000 c0746cd8 c0746cd8 c07091f0
9f00: 00000000 c0008944 c04f405c 00000025 ee00b000 60000153 c074ab00 00000000
9f20: 00000000 c074ab90 60000153 00000000 ef7fca5d c050860c 000000b6 c0036b88
9f40: c065ecc4 c06bc728 00000006 00000006 c074ab30 ef7fca40 c0739bdc 00000006
9f60: c0718dbc c0778c00 000000b6 c0718dc8 c06ed598 c06edd64 00000006 00000006
9f80: c06ed598 c003b438 00000000 c04e64f4 00000000 00000000 00000000 00000000
9fa0: 00000000 c04e64fc 00000000 c000e838 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 c0c0c0c0 c0c0c0c0
[<c03eef38>] (__clk_put) from [<c03f0ec8>] (of_clk_set_defaults+0xe0/0x2c0)
[<c03f0ec8>] (of_clk_set_defaults) from [<c02c3124>] (platform_drv_probe+0x18/0xa4)
[<c02c3124>] (platform_drv_probe) from [<c02c1d0c>] (driver_probe_device+0x10c/0x22c)
[<c02c1d0c>] (driver_probe_device) from [<c02c1eb8>] (__driver_attach+0x8c/0x90)
[<c02c1eb8>] (__driver_attach) from [<c02c0544>] (bus_for_each_dev+0x54/0x88)
[<c02c0544>] (bus_for_each_dev) from [<c02c150c>] (bus_add_driver+0xd4/0x1d0)
[<c02c150c>] (bus_add_driver) from [<c02c24e0>] (driver_register+0x78/0xf4)
[<c02c24e0>] (driver_register) from [<c07091f0>] (fimc_md_init+0x14/0x30)
[<c07091f0>] (fimc_md_init) from [<c0008944>] (do_one_initcall+0x80/0x1d0)
[<c0008944>] (do_one_initcall) from [<c06edd64>] (kernel_init_freeable+0x108/0x1d4)
[<c06edd64>] (kernel_init_freeable) from [<c04e64fc>] (kernel_init+0x8/0xec)
[<c04e64fc>] (kernel_init) from [<c000e838>] (ret_from_fork+0x14/0x3c)
Code: ebfff4ae e5943014 e5942018 e3530000 (e5823000)
Let's create a per-user handle here so that clk_put() can
properly unlink it and free the handle. Now that we allocate a
clk structure here we need to free it if __clk_get() fails so
bury the __clk_get() call in __of_clk_get_from_provider(). We
need to handle the same problem in clk_get_sys() so export
__clk_free_clk() to clkdev.c and do the same thing, except let's
use a union to make this code #ifdef free.
This fixes the above crash, properly calls __clk_get() when
of_clk_get_from_provider() is called, and cleans up the clk
structure on the error path of clk_get_sys().
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Alban Browaeys <prahal@yahoo.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Private clock framework data structures should be private, surprisingly.
Now that all platforms and drivers have been updated to remove static
initializations of struct clk and struct clk_core objects and all
references to clk-private.h have been removed we can move the
definitions of these structures into drivers/clk/clk.c and delete the
header.
Additionally the ugly DEFINE_CLK macros have been removed. Those were
used for static definitions of struct clk objects. That practice is no
longer allowed.
Finally __clk_init is staticized as it is no longer declared in any
header.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Moves clock state to struct clk_core, but takes care to change as little API as
possible.
struct clk_hw still has a pointer to a struct clk, which is the
implementation's per-user clk instance, for backwards compatibility.
The struct clk that clk_get_parent() returns isn't owned by the caller, but by
the clock implementation, so the former shouldn't call clk_put() on it.
Because some boards in mach-omap2 still register clocks statically, their clock
registration had to be updated to take into account that the clock information
is stored in struct clk_core now.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: adapted clk_has_parent to struct clk_core
applied OMAP3+ DPLL fix from Tero & Tony]
As it has never been used.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As clk_unprepare_unused_subtree and clk_disable_unused_subtree are
always called with a valid struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The phase setter and getter were not exported until now, which was causing
build breakages when callers were compiled as module. Export these two
functions.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some clock drivers want to find the closest rate on the input of
a mux instead of a rate that's less than or equal to the desired
rate. Add a generic mux function to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some of the clks can be registered & unregistered before the clk related debugfs
entries are initialized at late_initcall. In the unregister path checking for only
dentry before clk_debug_init() would lead dangling pointers in the debug clk list,
because the list is already populated in register path and the clk pointer freed in
unregister path.
The side effect of not removing it from the list is either a null pointer
dereference or if lucky to boot the system, the number of clk entries in
debugfs disappear.
We could add more checks like if (inited && !clk->dentry) but just removing
the check for dentry made more sense as debugfs_remove_recursive() seems to be
safe with null pointers. This will ensure that the unregistering clk would be
removed from the debug list in all the code paths.
Without this patch kernel would crash with log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G B 3.19.0-rc3-00007-g412f9ba-dirty #840
Hardware name: Qualcomm (Flattened Device Tree)
task: ed948000 ti: ed944000 task.ti: ed944000
PC is at strlen+0xc/0x40
LR is at __create_file+0x64/0x1dc
pc : [<c04ee604>] lr : [<c049f1c4>] psr: 60000013
sp : ed945e40 ip : ed945e50 fp : ed945e4c
r10: 00000000 r9 : c1006094 r8 : 00000000
r7 : 000041ed r6 : 00000000 r5 : ed4af998 r4 : c11b5e28
r3 : 00000000 r2 : ed945e38 r1 : a0000013 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 8020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xed944248)
Stack: (0xed945e40 to 0xed946000)
5e40: ed945e7c ed945e50 c049f1c4 c04ee604 c0fc2fa4 00000000 ecb748c0 c11c2b80
5e60: c0beec04 0000011c c0fc2fa4 00000000 ed945e94 ed945e80 c049f3e0 c049f16c
5e80: 00000000 00000000 ed945eac ed945e98 c08cbc50 c049f3c0 ecb748c0 c11c2b80
5ea0: ed945ed4 ed945eb0 c0fc3080 c08cbc30 c0beec04 c107e1d8 ecdf0600 c107e1d8
5ec0: c107e1d8 ecdf0600 ed945f54 ed945ed8 c0208ed4 c0fc2fb0 c026a784 c04ee628
5ee0: ed945f0c ed945ef0 c0f5d600 c04ee604 c0f5d5ec ef7fcc7d c0b40ecc 0000011c
5f00: ed945f54 ed945f10 c026a994 c0f5d5f8 c04ecc00 00000007 ef7fcc95 00000007
5f20: c0e90744 c0dd0884 ed945f54 c106cde0 00000007 c117f8c0 0000011c c0f5d5ec
5f40: c1006094 c100609c ed945f94 ed945f58 c0f5de34 c0208e50 00000007 00000007
5f60: c0f5d5ec be9b5ae0 00000000 c117f8c0 c0af1680 00000000 00000000 00000000
5f80: 00000000 00000000 ed945fac ed945f98 c0af169c c0f5dd2c ed944000 00000000
5fa0: 00000000 ed945fb0 c020f298 c0af168c 00000000 00000000 00000000 00000000
5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ebcc6d33 bfffca73
[<c04ee604>] (strlen) from [<c049f1c4>] (__create_file+0x64/0x1dc)
[<c049f1c4>] (__create_file) from [<c049f3e0>] (debugfs_create_dir+0x2c/0x34)
[<c049f3e0>] (debugfs_create_dir) from [<c08cbc50>] (clk_debug_create_one+0x2c/0x16c)
[<c08cbc50>] (clk_debug_create_one) from [<c0fc3080>] (clk_debug_init+0xdc/0x144)
[<c0fc3080>] (clk_debug_init) from [<c0208ed4>] (do_one_initcall+0x90/0x1e0)
[<c0208ed4>] (do_one_initcall) from [<c0f5de34>] (kernel_init_freeable+0x114/0x1e0)
[<c0f5de34>] (kernel_init_freeable) from [<c0af169c>] (kernel_init+0x1c/0xfc)
[<c0af169c>] (kernel_init) from [<c020f298>] (ret_from_fork+0x14/0x3c)
Code: c0b40ecc e1a0c00d e92dd800 e24cb004 (e5d02000)
---[ end trace b940e45b5e25c1e7 ]---
Fixes: 6314b6796e "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This new function is similar to clk_set_parent(), except that it doesn't
actually change the parent. It merely checks that the given parent clock
can be a parent for the given clock.
A situation where this is useful is to check that a particular setup is
valid before switching to it. One specific use-case for this is atomic
modesetting in the DRM framework where setting a mode is divided into a
check phase where a given configuration is validated before applying
changes to the hardware.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We don't need to fetch the parent index for clocks if they only
have one parent. Doing this also avoid an unnecessary allocation
for the parent cache.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The commit 646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 6314b6796e (clk: Don't hold prepare_lock across debugfs
creation, 2014-09-04) forgot to update one place where we hold
the prepare_lock while creating debugfs directories. This means
we still have the chance of a deadlock that the commit was trying
to fix. Actually fix it by moving the debugfs creation outside
the prepare_lock.
Cc: <stable@vger.kernel.org> # 3.18
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: 6314b6796e "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed lockdep_assert]
This is in preparation for clock providers to not have to deal with struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Instead of struct clk, as this should be only used by providers.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
